General information on paint

Topcoats

~24min read
2special tools

2K HS topcoat

Designation:

  • 2K HS solid colour topcoat -L2K 073.....-
  • 2K HS mixing colour -L2K 074.....-

Product description

The 2K HS topcoat series is a high-solids solid colour topcoat system. It is intended for passenger car refinishing.

The colour range is comprehensively covered by a matching range of mixing colours.

Features:

  • easy application
  • fast drying
  • excellent topcoat sag resistance
  • VOC-compliant, below 420 g/l

Application information

Substrate

Suitable substrates:

  • cured, solvent-resistant, well-preserved and sanded original or old paint finishes
  • primed or surfaced areas

Suitable base materials:

  • depending on object and substrate, as per the build-up recommendation

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with a random orbital sander and dust extraction, P400-500.

VW UP. Allgemeine Informationen Lack

- Or sand "wet" with sanding paper P800-1000.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Mixing ratio:

- 3:1 by volume with:

  • 2K VHS hardener, short -LHA 009 050 A2- (for small areas, spot repair)
  • 2K VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5- (for small to medium areas, at medium temperatures)
  • 2K VHS hardener, long -LHA 009 052 A2-/-LHA 009 052 A3- (for larger areas at medium temperatures)
  • 2K VHS hardener, extra long -LHA 009 053 A2- (for large areas and high temperatures)
  • see application information 2K VHS hardener


Note

The mixing ratio for satin black -L2K 073 3FZ A2- and satin grey -L2K 073 7DL A2- is 4:1 with 2K VHS hardener -LHA 009 051 A2-/-LVM 009 051 A5-.

VW UP. Allgemeine Informationen Lack

Processing/pot life:

- Ready-to-spray after 60-90 minutes at +20 °C

Can be thinned with 2K thinner, special -LVM 009 200 A2-, or with HS spot thinner -LVM 006 000 A2-, or with 2K thinner, long -LVM 009 300 A2-


Note

When using HS spot thinner -LVM 006 000 A2-, observe the ATI (application technical information).

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 °C material temperature

Application viscosity "Compliant" and "HVLP":

18-20 seconds

18-25 seconds for satin black -L2K 073 3FZ A2- and satin grey -L2K 073 7DL A2-

VW UP. Allgemeine Informationen Lack

- 12.5 % thinner addition at +20 °C material temperature

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's data): "Compliant" 1.2-1.4 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" 1.3–1.4 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- To achieve the recommended dry film thickness of 50-60 µm, 1.5 spray passes are required.


Note

  • When used for small damage repair (Clever Repair process), the 12.5 % 2K thinner, special -LVM 009 200 A2- can be replaced by 12.5 % HS spot thinner -LVM 006 000 A2-.
  • Do not use on horizontal surfaces.
  • During application, the first half pass should form a closed thin film, which is then followed directly by a full closed spray pass.
  • With weak-hiding shades, it may be necessary to apply another spray pass after the appropriate flash-off time. Recoating 2K HS topcoat over itself is possible within 24 hours without intermediate sanding.
  • The mixing colours of this mixing colour series can only be used within the scope of colour formulas. When processing individual mixing colours on their own, considerable deviations from the information given in the application technical information are possible.
VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 ºC room temperature:

  • dust-dry after 20-30 minutes
  • ready for assembly after 5-6 hours
  • dry overnight
VW UP. Allgemeine Informationen Lack

The final flash-off time with forced drying is at least 5-10 minutes.

VW UP. Allgemeine Informationen Lack

Forced drying at +60 °C object temperature for 15-20 minutes

VW UP. Allgemeine Informationen Lack

The final flash-off time for infrared drying is at least 5 minutes.

VW UP. Allgemeine Informationen Lack

Infrared drying of light shades with short-wave emitter: 5 minutes at 50 % power, then 10 minutes at 100 % power

Infrared drying of light shades with medium-wave emitter: 15 minutes

Infrared drying of dark shades with medium-wave emitter: 12 minutes

Infrared drying of dark shades with short-wave emitter: 12 minutes at 50 % power


Note

When using a short-wave emitter at 100 % power, dark shades carry a risk of blistering or bubbling during rework.

VW UP. Allgemeine Informationen Lack

Special notes:

Flexibilizing:

  • The base material must first be mixed with 15 % elasticizer -ALZ 011 001-.
  • Mixing ratio with 2K VHS hardeners, 3:1 with 15 % thinner.

Matting/texturing:

VW UP. Allgemeine Informationen Lack

  • The base material must first be mixed with 100 % matting component -ALN 775 106- / fine texturing component -ALN 775 108-.


Note

  • For the 2K universal topcoats Matt Black -L2K 073 3FZ A2- and Matt Grey -L2K 073 7DL A2-, no further addition of matting component -ALN 775 106- is required, as these are already matted.
  • Mixing ratio with 2K VHS hardener -LHA 009 051 A2- / -LVM 009 051 A5- is 4:1 with 15 % thinner.
  • For an even paint film surface, 2 spray passes (with 5-10 minutes flash-off time between them) are required.
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of the 2K HS universal topcoats -L2K 073.....- is 24 months from the production date.

The guaranteed storage stability of the 2K HS mixing paints -L2K 074.....- is 36 months from the production date. Both products must be used no later than the date stated on the label when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

Aquaplus system (solid and metallic)

Designation:

  • Solid waterborne mixing paint -LWM 075...-
  • Metallic waterborne mixing paint -LWM 076...-
  • Solid waterborne primer -LUW/LWG 038...-
  • Metallic waterborne primer -LMW/LWG 039...-

Product description

The Aquaplus system is a high-quality, water-thinnable basecoat system. It is based on a special PU dispersion technology for high-quality solid and metallic two-coat finishes.

Features:

  • easy application
  • good sag resistance
  • high hiding power
  • can be overcoated with 2K HS clearcoat
  • VOC-compliant


Note

Overcoating with 2K HS clearcoat produces a high-gloss, weather-resistant topcoat finish.

Application information

Substrate

Suitable substrates:

  • intact existing finishes
  • primed or filled surfaces (2K HS filler)
  • substrates isolated with 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-
  • plastic surfaces: substrates isolated with 2K plastic adhesion primer -LKF 696 009 A2- / -LKF 696 040 A2-
  • see special notes

Pretreatment of substrates:

- Thoroughly clean the factory or existing paint, or 2K HS filler, with Silicone Remover -LVM 020 000 A5- or Silicone Remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with a random orbital sander and dust extraction, P400-500.

VW UP. Allgemeine Informationen Lack

- Or sand "wet" with sanding paper P800-1000.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.

Special Notes

  • Sanded-through areas must be isolated with 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-. Sanded-through areas must not be larger than Ø 5.0 cm.
  • When using 2K HS filler, bare spots must be isolated with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-.

Processing

Mixing containers:

  • Plastic containers or internally coated tinplate containers

Strainers:

  • Filter waterborne basecoats through waterproof 125 µm quick strainers before application with cup gun systems.

Thinner:

  • Demineralized water Aquaplus -LVW 010 000 A5- (according to ISO 3696)
  • Use Aquaplus measuring stick.
  • At higher temperatures (>+25 ºC) and high relative humidity (>60 %), adding 0-5 % demineralized water -LVW 010 000 A5- is sufficient.


Note

  • For safety reasons, mixtures that simultaneously contain micro silver, extra -LWM 076 817 A2/A4- and laser oxide -LWM 075 831 A1- must not be stored. There is a risk of pressure build-up in the sealed container!
  • Dispose of any leftover material immediately and in accordance with regulations.
VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

VW UP. Allgemeine Informationen Lack

- Add 10 % thinner at +20 ºC material temperature.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- One work step consists of: applying a thin first spray pass, followed by a normal second spray pass. For effect shades, a "finish spray pass" is recommended.


Note

For shades with weak hiding power, further spray passes may be necessary after adequate flash-off time.

VW UP. Allgemeine Informationen Lack

Drying

VW UP. Allgemeine Informationen Lack

The flash-off time before clearcoat application is 20 minutes at a room temperature of +20 ºC.

Options for shortening the flash-off time on smaller areas are:

  • Flash-off of the painted surface to a matt finish can be accelerated by blowing with air nozzles (hand-held or stand-mounted units).
  • Blowing with the spray gun is also possible after a waiting time of at least 5 minutes.

Options for shortening the flash-off time on larger areas are:

  • Flash-off of the painted surfaces to a matt finish can be accelerated by using stationary air systems (e.g. ceiling system), infrared emitters or oven drying.
  • Ceiling system 10-15 minutes
  • Infrared drying 3-5 minutes
  • Cooling time at least 5 minutes
VW UP. Allgemeine Informationen Lack

Oven drying at +60 ºC

  • Combi booth at least 10 minutes including heat-up time
  • Drying oven at least 5 minutes
  • Cooling time at least 5 minutes


Note

The specified flash-off/drying times depend on temperature, air humidity, air downdraft speed in the spray booth and number of spray passes. In every case, the painted surface must be allowed to flash off completely to a matt finish.

VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • 2K HS clearcoat from the Volkswagen original paint range

Special Notes

Blend-in spray system (to achieve a visually flawless colour transition to adjacent parts)

  • Preparation:

- Sand filled surfaces (dry with P 400-500 or wet with waterproof paper P 800-1000).

- Thoroughly sand the adjacent unfilled surface with a fine sanding pad.

- Thoroughly clean the entire area with Silicone Remover -LVM 020 000 A5- to remove dust, sanding residue and other contamination.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.

- Allow wet-sanded and cleaned surfaces to flash off thoroughly.

  • Blend-in spray system for metallic and solid shades:

- Spray the filled surface with waterborne basecoat adjusted ready to spray, to full hiding.

- Extend each spray pass slightly further; this overlap leaves only a fog zone.

- Make the run-out zone larger and blend in carefully with reduced pressure.

- After adequate final flash-off time, the surface can be overcoated with 2K HS clearcoat.

Processing the Products

  • Spray equipment must be suitable for waterborne products; observe manufacturer's specifications.
  • The mixing paints of this topcoat series can only be used within colour formulas. When processing individual mixing paints alone, considerable deviations from the information given in the application technical information are possible.

Cleaning the Equipment

  • Rinse with deionized water Aquaplus -LVW 010 000 A5- before and after use. Then rinse with Nitro Thinner -LVE 856 000 A3-.

Disposal

  • Collect liquid residues of water-reducible products separately from liquid residues of conventional products. If they are mixed, disposal may be impossible, and in any case it is more difficult and therefore more expensive.
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of the individual products is:

  • Solid waterborne mixing paints -LWM 075...- 24 months from the production date.
  • Solid waterborne primers -LUW/LWG 038...- 24 months from the production date.
  • Metallic waterborne mixing basecoat -LWM 076...- 24 months from production date.
  • Metallic waterborne basecoats -LMW/LWG 039...- 18/24 months from production date.

All products are usable until the date stated on the label at the latest, when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The optimum storage temperature is +20 °C (must not fall below +5 °C).

The preferred storage temperature is +15 °C to +25 °C.

Short-term storage (approx. 4 weeks) at +5 °C to +35 °C is possible.

VW UP. Allgemeine Informationen Lack

Aquaplus system (pearl effect and heliochrome)

Designation:

  • Pearl effect waterborne basecoat -LPW 040...-
  • Heliochrome waterborne basecoat -LHW 046...-
  • Pearl effect waterborne mixing basecoat -LWM 076...-

Product description

The Aquaplus system is a high-quality waterborne basecoat system based on special PU dispersions.

The basecoat can be used for pearl effect/heliochrome two-coat finishes or nacre effect three-coat finishes on passenger cars and commercial vehicles.

Features:

  • easy application
  • good sag resistance
  • high hiding power
  • can be overcoated with 2K HS clearcoat
  • VOC-compliant


Note

Overcoating with 2K HS clearcoat produces a high-gloss, weather-resistant topcoat finish.

Application information

Substrate

Suitable substrates:

  • intact existing finishes
  • primed or filled surfaces (2K HS filler)
  • substrates isolated with 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-
  • plastic surfaces: substrates isolated with 2K plastic adhesion primer -LKF 696 009 A2- / -LKF 696 040 A2-
  • see special notes

Pretreatment of substrates:

- Thoroughly clean the factory or existing paint, or 2K HS filler, with Silicone Remover -LVM 020 000 A5- or Silicone Remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with a random orbital sander and dust extraction, P400-500.

VW UP. Allgemeine Informationen Lack

- Or sand "wet" with sanding paper P800-1000.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.

Special Notes

  • Sand-through areas must be sealed with 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-. Sand-through areas must not be larger than Ø 5.0 cm.
  • When using 2K HS filler, bare spots must be isolated with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-.

Processing

Mixing containers:

  • Plastic containers or internally coated tinplate containers

Strainers:

  • Filter waterborne basecoats through water-resistant 125 µm quick-filters before application with cup gun systems.

Thinner:

  • Demineralized water Aquaplus -LVW 010 000 A5- (according to ISO 3696)
  • Use Aquaplus measuring stick.
  • At higher temperatures (>+25 ºC) and high relative humidity (>60 %), adding 0-5 % demineralized water -LVW 010 000 A5- is sufficient.

Pre-coating:

  • Three-coat nacre shades require a special base colour (application of solid waterborne basecoat). The respective shade must be determined from the formula information system.
  • For nacre finishes, pearl effect waterborne basecoat is applied.
VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

VW UP. Allgemeine Informationen Lack

- Add 10 % thinner at +20 ºC material temperature.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- One work step consists of: applying a thin first spray pass, followed by a normal second spray pass. For effect shades, a "finish spray pass" is recommended.


Note

  • For shades with weak hiding power, further spray passes may be necessary after adequate flash-off time.
  • The total film build (including special base colour solid waterborne basecoat) must not exceed 45 µm.
VW UP. Allgemeine Informationen Lack

Drying

VW UP. Allgemeine Informationen Lack

The flash-off time before clearcoat application is 20 minutes at a room temperature of +20 ºC.

Options for shortening the flash-off time on smaller areas are:

  • Flash-off of the painted surface to a matt finish can be accelerated by blowing with air nozzles (hand-held or stand-mounted units).
  • Blowing with the spray gun is also possible after a waiting time of at least 5 minutes.

Options for shortening the flash-off time on larger areas are:

  • Flash-off of the painted surfaces to a matt finish can be accelerated by using stationary air systems (e.g. ceiling system), infrared emitters or oven drying.
  • Ceiling system 10-15 minutes
  • Infrared drying 3-5 minutes
  • Cooling time at least 5 minutes
VW UP. Allgemeine Informationen Lack

Oven drying at +60 ºC

  • Combi booth at least 10 minutes including heat-up time
  • Drying oven at least 5 minutes
  • Cooling time at least 5 minutes


Note

The specified flash-off/drying times depend on temperature, air humidity, air downdraft speed in the spray booth and number of spray passes. In every case, the painted surface must be allowed to flash off completely to a matt finish.

VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • 2K HS clearcoat from the Volkswagen original paint range

Special Notes


Note

  • Whether finishes must be applied as two-coat or three-coat (with a special base colour) depends on the factory finish.
  • The respective base colour is specified in the formula information system.

Blend-in spray system (to achieve a visually flawless colour transition to adjacent parts)

  • Preparation:

- Sand filled surfaces (dry with P 400-500 or wet with waterproof paper P 800-1000).

- Thoroughly sand the adjacent unfilled surface with a fine sanding pad.

- Thoroughly clean the entire area with Silicone Remover -LVM 020 000 A5- to remove dust, sanding residue and other contamination.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.

- Allow wet-sanded and cleaned surfaces to flash off thoroughly.

  • Two-coat pearl effect/heliochrome shades:

- Spray the filled area to full coverage with pearl effect/heliochrome waterborne basecoat, adjusted to sprayable viscosity.

- Extend each spray pass slightly further; this overlap leaves only a fog zone.

- Make the run-out zone larger and blend in carefully with reduced pressure.

- After adequate final flash-off time, the surface can be overcoated with 2K HS clearcoat.

  • Three-coat nacre shades:

- Lightly spray the filled area with solid waterborne basecoat adjusted to sprayable viscosity (see base colour processing), at reduced pressure (observe flash times).

- Spray the same area with nacre effect waterborne basecoat adjusted to sprayable viscosity, overlapping slightly (at reduced pressure), and blend into the original.

- After each spray pass, blow the gun dry.

Processing the Products

  • Spray equipment must be suitable for waterborne products; observe manufacturer's specifications.
  • The mixing paints of this topcoat series can only be used within colour formulas. When processing individual mixing paints alone, considerable deviations from the information given in the application technical information are possible.

Cleaning the Equipment

  • Rinse with deionized water Aquaplus -LVW 010 000 A5- before and after use. Then rinse with Nitro Thinner -LVE 856 000 A3-.

Disposal

  • Collect liquid residues of water-reducible products separately from liquid residues of conventional products. If they are mixed, disposal may be impossible, and in any case it is more difficult and therefore more expensive.
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of the individual products is:

  • Pearl effect waterborne mixing basecoat -LWM 076...- 24 months from production date.
  • Pearl effect waterborne basecoat -LPW 040...- 18/24 months from production date.
  • Heliochrome waterborne basecoat -LHW 046...- 18 months from production date.

All products are usable until the date stated on the label at the latest, when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The optimum storage temperature is +20 °C (must not fall below +5 °C).

The preferred storage temperature is +15 °C to +25 °C.

Short-term storage (approx. 4 weeks) at +5 °C to +35 °C is possible.

VW UP. Allgemeine Informationen Lack

Aquaplus spray-in system

Designation:

  • Spray-in additive for Aquaplus -LVM 030 000 A2-

Product description

The spray-in additive for Aquaplus is especially suited for blending Aquaplus waterborne basecoat. It simplifies the blending process.

Application information

Substrate

Suitable substrates:

  • Primed or filled areas with 2K HS filler
  • cured, solvent-resistant, well-preserved and sanded original or old paint finishes

Suitable base materials:

  • Depending on object and substrate, per our build-up recommendation

Pretreatment of substrates:

- Thoroughly clean the factory or existing paint, or 2K HS filler, with Silicone Remover -LVM 020 000 A5- or Silicone Remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with dual-action sander and dust extraction, P400-500, or wet sand with waterproof abrasive paper P800-1000.

VW UP. Allgemeine Informationen Lack

- Sand the blend area of the undamaged original finish with abrasive paper P1000-1200.

VW UP. Allgemeine Informationen Lack

- Clean again with a suitable cleaner before refinishing to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

- Allow wet-sanded and cleaned surfaces to flash off thoroughly.

VW UP. Allgemeine Informationen Lack

Processing

Thinning is not required.

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity 4 mm at +20 °C, DIN 53211

- The product is ready to spray at processing viscosity.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- Apply the adjusted Aquaplus waterborne basecoat to the damaged area with 3-5 light/dry spray passes, depending on shade and hiding power, at reduced pressure (0.8-1.5 bar).


Note

Regardless of the manufacturer's specifications, the inlet pressure should be reduced as specified for this spray-in system.

VW UP. Allgemeine Informationen Lack

Drying

VW UP. Allgemeine Informationen Lack

Flash-off time before clearcoat application

At room temperature of +20 °C, allow to flash off for 15-20 minutes.

Ways to shorten the flash-off time:

  • Flash-off of the painted surface can be accelerated by blowing with air nozzles or by forced drying (IR or oven drying) until the surface turns dull.
  • Blowing with the spray gun is also possible after a waiting time of at least 5 minutes.
  • Minimum drying time is 5 minutes.
VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • 2K HS clearcoat


Note

The product must not be used neat.

VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of the spray-in additive for Aquaplus -LVM 030 000 A2- is 24 months from production date. Usable until the date stated on the label at the latest, when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The optimum storage temperature is +5 °C to +35 °C.


Note

Temperatures above or below this range impair the product.

VW UP. Allgemeine Informationen Lack

Aqua Premium system

Designation:

  • Solid waterborne mixing basecoat -LWM 083...-
  • Metallic/pearl effect/special effect waterborne mixing basecoat -LWM 084/086...-
  • Solid waterborne basecoat -LWG 055...-
  • Metallic waterborne basecoat -LWG 056...-
  • Pearl effect waterborne basecoat -LWG 057...-
  • Flop Control -LWM 085 386 A2-
  • System component A -LWM 083 385 A3-
  • System component B -LWM 085 387 A3-

Product description

The Aqua Premium system is an innovative waterborne basecoat system. The mixing system contains all solid and effect shades for passenger car refinishing.

Features:

  • Easy and fast to apply
  • High process reliability thanks to uniform effect orientation
  • Short process times
  • Easy and reliable blending
  • Versatile applications (interior, multi-layer and multi-colour finishes)

Application information

Substrate

Suitable substrates:

  • primed or filled surfaces (2K HS filler)
  • intact existing finishes
  • For plastic surfaces: translucent adhesion promoter -ALO 822 000 10- + 2K HS filler (flexibilised)
  • plastic surfaces: substrates isolated with 2K plastic adhesion primer -LKF 696 009 A2- / -LKF 696 040 A2-
  • see special notes

Pretreatment of substrates:

- Thoroughly clean the factory or existing paint, or 2K HS filler, with Silicone Remover -LVM 020 000 A5- or Silicone Remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Dry sand with dual-action sander and dust extraction, P500-600.

VW UP. Allgemeine Informationen Lack

- Or sand "wet" with sanding paper P800-1000.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.

Special Notes

  • Sand-through areas must be sealed with 1K wash primer -LVM 044 007 A2-/-LVM 044 171 A2-. Sand-through areas must not be larger than Ø 5.0 cm.
  • When using 2K HS filler, bare spots must be isolated with 2K wash primer -LHV 043 000 A2- or 1K wash primer -LVM 044 007 A2- / -LVM 044 171 A2-.

Standard application procedure

Mixing containers:

  • Plastic containers or internally coated tinplate containers

Strainers:

  • Filter waterborne basecoats through waterproof 125 µm quick strainers before application with cup gun systems.

Additives:

(at normal/high temperature and low humidity, depending on object size)

  • Additive for Aqua Premium -LVM 035 200 A3-
  • Additive for Aqua Premium -LVM 035 301 A3-
  • Use the standard Aqua Premium measuring stick.


Note

After adding the additive, process the material within 24 hours.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

VW UP. Allgemeine Informationen Lack

- For solid shades, add 10% additive for Aqua Premium -LVM 035 200 A3/LVM 035 301 A3- at a material temperature of +20 °C.

- For metallic/pearl effect shades, add 20 % Additive for Aqua Premium -LVM 035 200 A3/LVM 035 301 A3- at +20 °C material temperature.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- One work step includes 1.5 spray passes. Apply one normal spray pass, then apply a "finish spray pass"/effect spray pass.


Note

For shades with low hiding power, it may be necessary to apply another spray pass (wet-on-wet) after the appropriate flash-off time.

VW UP. Allgemeine Informationen Lack

Drying

VW UP. Allgemeine Informationen Lack

The flash-off time before clearcoat application lasts until a completely matt surface is present.

Recommended film thicknesses:

  • for solid shades: 12-25 µm
  • for metallic shades: 10-15 µm
  • for pearl effect shades: 15-20 µm

Options for shortening the flash-off time on smaller areas are:

  • Flash-off of the painted surface to a matt finish can be accelerated by blowing with air nozzles (hand-held or stand-mounted units).
  • Blowing with the spray gun is also possible after a waiting time of at least 5 minutes.

Options for shortening the flash-off time on larger areas are:

VW UP. Allgemeine Informationen Lack

  • Flash-off of the painted surfaces to a matt finish can be accelerated by using stationary air systems (e.g. ceiling system), infrared emitters or oven drying.

Application of 3-stage shades and multi-tone paint finishes

Hardener:

  • Aqua Premium hardener -LVM 045 000 A1-

Additives:

(at high temperature and low humidity)

  • Additive for Aqua Premium -LVM 035 301 A3-
  • Use the Aqua Premium measuring stick for 3-stage shades.


Note

After adding the additive, process the material within 24 hours.

Pot life:

  • Solid shade: 90-120 minutes at +20 °C room temperature.
  • Effect shade: 45-60 minutes at +20 °C room temperature.
VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

- For 3-stage shades, add 5 % Aqua Premium hardener -LVM 045 000 A1- to the base shade only.

VW UP. Allgemeine Informationen Lack

- For solid shades, add 10 % Additive for Aqua Premium -LVM 035 301 A3- at +20 °C material temperature.

- For metallic/pearl effect shades, add 20 % Additive for Aqua Premium -LVM 035 301 A3- at +20 °C material temperature.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- One work step includes 1.5 spray passes. Apply one normal spray pass, then apply a "finish spray pass"/effect spray pass.


Note

For shades with low hiding power, it may be necessary to apply another spray pass (wet-on-wet) after the appropriate flash-off time.

VW UP. Allgemeine Informationen Lack

Drying

VW UP. Allgemeine Informationen Lack

The flash-off time before clearcoat application lasts until a completely matt surface is present (without air blowing).

  • Flashing off with air blowers takes 5-10 minutes at 20-40 °C, until a completely matt surface is present.
  • Final flash-off takes 10-15 minutes at 60-65 °C. Allow the base shade to cool before applying the effect coat.


Note

The recommended masking tape for multi-tone paint finishes is "Konturenband blau" (blue contour tape).

VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • Effect shade
  • 2K HS clearcoat up to max. 72 hours after basecoat application

Interior painting application without clearcoat

Application:

  • Areas of application are vehicle interiors, e.g. the inner sides of engine compartments and luggage compartments, where a satin-gloss and durable surface without an additional clearcoat is required.

Hardener:

  • Aqua Premium hardener -LVM 045 000 A1-

Additives:

(at normal/high temperature and low humidity, depending on object size)

  • Additive for Aqua Premium -LVM 035 200 A3-
  • Additive for Aqua Premium -LVM 035 301 A3-
  • Use the Aqua Premium measuring stick for interior painting.

Pot life:

  • Solid shade: 45-60 minutes at +20 °C room temperature
  • Effect shade: 30-60 minutes at +20 °C room temperature
VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

- Application viscosity at +20 ºC material temperature; for "Compliant" and "HVLP" this is the mixed viscosity.

- Add 10 % Aqua Premium hardener -LVM 045 000 A1- to the shade.

VW UP. Allgemeine Informationen Lack

- For solid shades, add 10% additive for Aqua Premium -LVM 035 200 A3/LVM 035 301 A3- at a material temperature of +20 °C.

- For metallic/pearl effect shades, add 20 % Additive for Aqua Premium -LVM 035 200 A3/LVM 035 301 A3- at +20 °C material temperature.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.2-1.3 mm.

- Set spray nozzle (see manufacturer's specifications): "HVLP" WSB/1.3 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0 bar.

- Set atomizing air pressure (see manufacturer's specifications): "HVLP" 0.7 bar.

VW UP. Allgemeine Informationen Lack

- One work step includes 1.5 spray passes. Apply one normal spray pass, then apply a "finish spray pass"/effect spray pass.


Note

For shades with low hiding power, it may be necessary to apply another spray pass (wet-on-wet) after the appropriate flash-off time.

VW UP. Allgemeine Informationen Lack

Drying

Air drying overnight at +20 °C room temperature

Alternatively, drying can be carried out for 15-20 minutes at 60-65 °C (oven drying).

Special Notes

Processing the Products

  • Spray equipment must be suitable for waterborne products; observe manufacturer's specifications.
  • The mixing paints of this topcoat series can only be used within colour formulas. When processing individual mixing paints alone, considerable deviations from the information given in the application technical information are possible.

Cleaning the Equipment

  • Rinse with deionized water Aquaplus -LVW 010 000 A5- before and after use. Then rinse with Nitro Thinner -LVE 856 000 A3-.

Disposal

  • Collect liquid residues of water-reducible products separately from liquid residues of conventional products. If they are mixed, disposal may be impossible, and in any case it is more difficult and therefore more expensive.
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability of the individual products is:

  • Solid waterborne paint -LWM 083...- 36 months from production date (exceptions: ocher -LWM 083 328-, lasur oxide -LWM 083 331- and maroon -LWM 083 332- 24/36 months from production date), (exception super deep black -LWM 083 388 A2- 48 months from production date).
  • Metallic/pearl effect/special effect waterborne paint -LWM 084...- 24 months from production date.
  • Aqua Premium solid/basecoat -LWG 055...- 24 months from production date.
  • Metallic waterborne basecoat -LWG 056...- 18/24 months from production date.
  • Pearl effect waterborne basecoat -LWG 057...- 18/24 months from production date.
  • Additive for Aqua Premium -LVM 035 200 A3/LVM 035 301 A3- 24 months from production date.
  • Flop Control -LWM 085 386 A2- 24 months from production date.
  • System component A -LWM 083 385 A3- 24 months from production date.
  • System component B -LWM 085 387 A3- 24 months from production date.

All products are usable until the date stated on the label at the latest, when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The optimum storage temperature is +20 °C.

The preferred storage temperature is +15 °C to +25 °C.

Short-term storage (a few days) at +5 °C to +35 °C is possible.

VW UP. Allgemeine Informationen Lack

Aqua Premium tinting system

Designation:

  • Tinting additive for Aqua Premium -LVM 035 100 A3-

Product description

To achieve a visually flawless colour transition in the blend area or adjacent parts, e.g. front fender or door.

Application information

Substrate

Suitable substrates:

  • Primed or filled areas with 2K HS filler
  • intact existing paint
  • plastic surfaces: substrates isolated with 2K plastic adhesion primer -LKF 696 009 A2- / -LKF 696 040 A2-
  • see special notes

Pretreatment of substrates:

- Thoroughly clean the factory or existing paint, or 2K HS filler, with Silicone Remover -LVM 020 000 A5- or Silicone Remover, long -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Sand dry with a dual-action sander and dust extraction, P500, or sand wet with waterproof abrasive paper P 800 - 1000.

VW UP. Allgemeine Informationen Lack

- The adjacent area/component around the repair area must be thoroughly sanded over a wide area with P1000 - 3000 or with a sanding pad (e.g. ultra-fine). If beads, edges or grip recesses are present, a sanding pad must also be used beforehand.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

- Wipe off excess silicone remover with a lint-free cloth, leaving no streaks.