Cleaning agents
Silicone remover
Designation:
- Silicone Remover -LSW 019 000 A5-, water-based
- Silicone Remover -LVM 020 000 A5-
- Silicone Remover, long -LVM 020 100 A5-
Product description Silicone Remover -LSW 019 000 A5-
Silicone Remover -LSW 019 000 A5- is a non-labelled, water-based cleaning agent with a low proportion of organic solvents and special cleaning additives.
Product description Silicone Remover -LVM 020 000 A5- and Silicone Remover, long -LVM 020 100 A5-
Silicone Remover -LVM 020 000 A5- is a fast-evaporating mixture. Silicone Remover, long -LVM 020 100 A5- is a mixture of slowly evaporating organic solvents. Both are mainly used to remove oil and grease residues.
Application information
Application
- The application area is the cleaning of sanded original or refinish paint, primed as well as filled and sanded surfaces before further refinishing.
Processing
- Apply silicone remover with a spray bottle or a clean fleece pad.
- Wipe the surface dry with a dry fleece pad before the silicone remover evaporates.
- Allow cleaned surfaces to flash off well or blow them dry before refinishing.
![]()
Note
- Allow the cleaned surface to dry completely before refinishing.
- Do not allow sprayed-on silicone remover to dry on the surface.
- The product is not suitable for cleaning spray guns and application equipment.
- Replace used or contaminated fleece pads in good time (always use a clean fleece pad).
- For heavy soiling, the cleaning process must be repeated.
- Silicone Remover -LSW 019 000 A5- is not suitable for removing release agent residues on UP-GF or other plastic surfaces.
Personal protective equipment:
- Observe the safety data sheet
- Wear personal protective equipment during application
Characteristics of Silicone Remover -LSW 019 000 A5-


Characteristics of Silicone Remover -LVM 020 000 A5-

Characteristics of Silicone Remover, long -LVM 020 100 A5-

Storage
The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

Plastic Cleaner
Designation:
- Plastic Cleaner -D 195 850 A1-
Product description
Plastic Cleaner -D 195 850 A1- is a liquid universal cleaner and thinner based on aromatic-free and low-n-hexane petroleum spirits. The product contains no chlorinated hydrocarbons; it does not attack the paint if the contact time is short.
Application information
Application
- Plastic Cleaner -D 195 850 A1- is mainly used for degreasing and cleaning substrates before applying adhesives and sealants.
- Careful cleaning of the bonding surfaces is essential for functional adhesion and mainly includes the removal of dust, oil and grease.
- Depending on the base of the above products, the cleaner can also be used to remove contamination, excess quantities of these materials and various underbody protection materials.
- For some applications, Plastic Cleaner -D 195 850 A1- is also suitable as a thinner for certain adhesives/sealants and coating compounds. Note that these products are normally applied undiluted; thinning only makes sense if a thinner consistency is required for special application processes or similar.
Processing
![]()
Note
- Before starting work, read the safety data sheet for precautions and safety advice.
- Even for products that do not require labeling, observe the precautions usual for chemical products.
- Depending on the degree of soiling, size and shape of the parts to be cleaned, Plastic Cleaner -D 195 850 A1- is applied either with a brush or a cleaning fleece or similar, and wiped off.
- To avoid contaminating the contents of the original container, the cleaner should either be poured onto the fleece (do not press firmly against the opening and do not turn the container upside down) or transferred into another container (sheet-metal can or similar).
- Only take out as much as is required for cleaning, and close the original container again immediately.
- The cleaned surface must dry completely (approx. 2 - 10 minutes depending on conditions) before the adhesive or sealant is applied.
- Blowing off with compressed air can shorten the drying time, but in unfavourable cases oil-contaminated compressed air can ruin the cleaning result.
- For open-pored substrates, wait at least 30 minutes after cleaning. When cleaning cut residual material (e.g. when refitting firmly bonded vehicle glass), the processing instructions of these products must be observed.
Characteristics

Plastic Cleaner, antistatic
Designation:
- Plastic Cleaner, antistatic -LVM 001 001 A2-
![]()
Note
The application and processing instructions for Plastic Cleaner, antistatic -LVM 001 001 A2- are described in the associated base components.
Possible base components are:
- "Adhesion promoter (transparent)"
- "2K plastic adhesion filler"
Industrial Dirt Remover
Designation:
- Industrial Dirt Remover -ABS 600 000 10-
Product description
Industrial Dirt Remover -ABS 600 000 10- is used to remove flash rust (metal dust) on vehicle bodies. The product is used undiluted.
![]()
Caution!
The product contains organic and inorganic acids.
When handling this product, always wear protective gloves and safety goggles!
Application information
![]()
Note
- Before starting work, read the safety data sheet for precautions and safety advice.
- Even for products that do not require labeling, observe the precautions usual for chemical products.
Application/Processing
The following must be observed during application:
- The temperature of the cleaner and the vehicle body must not exceed 25 ºC (do not expose the vehicle and product to direct sunlight).
- After washing the vehicle, apply the product to the bodywork with a brush or sponge. Allow the product to act for approx. 10 minutes (do not extend the exposure time, as this can attack the paint or plastic parts). Do not let the product dry on the surface.
- Rinse the bodywork/vehicle with plenty of water and wash it.
- If the vehicle is not clean after one application, repeat the cleaning process.
Characteristics

Storage
The guaranteed storage stability is 36 months from the production date. Use by the date shown on the label at the latest when stored in sealed original containers at +15 °C to +30 °C.
