General information on paint

Stone chip protection

~4min read
1special tools

Stone chip protection -AKR 311 KD1 05-

Designation:

  • Stone chip protection -AKR 311 KD1 05-, color black

Product description

Stone chip protection -AKR 311 KD1 05- is a fine, sprayable coating compound based on synthetic resins.

The dried film adheres very well to cleaned substrates as well as to bare and painted sheet metal.

It is characterized by high hiding power, good corrosion protection, high abrasion resistance and therefore also good stone chip protection properties.

After approx. 7 minutes, this fast-drying stone chip protection spray can be overpainted with commercially available vehicle paint systems.

Oven drying at approx. 60 °C is possible without problems.

Avoid exceptional mechanical stress (e.g. car wash) during the first weeks.

For the mechanical load capacity of this overpainted area, the paint manufacturer's specifications must also always be observed.

Application information

Application

  • Stone chip protection -AKR 311 KD1 05- is used on visible components such as front apron, rear apron and door sill panels as protection against stone chips, road salt and moisture corrosion, and can be overpainted quickly.
  • The material is also used to supplement stone chip protection coatings, for spot repairs and for repairs after accident repair work.


Note

  • Before starting work, read the safety data sheet for precautions and safety advice.
  • Even for products that do not require labeling, observe the precautions usual for chemical products.

Processing

  • Clean the areas to be treated with stone chip protection thoroughly beforehand. Remove rust.
  • The surfaces must be dry, free of grease and dirt, and largely free of dust.
  • The material should be at room temperature when applied.
  • Shake the can vigorously. When the ball rattles, continue shaking for approx. 1 minute.
  • Hold the can upright while spraying and spray from a distance of approx. 20-30 cm.
  • If masking was applied before spraying, the masking must be removed before the material dries.
  • Abrasion and corrosion protection increase with film thickness. Therefore, after a short flash-off time, repeat the spraying process once or twice.
  • To avoid spray shadows, it is advisable to spray using the cross-pass method.
  • After use, hold the can with the valve facing down and spray the valve empty until only propellant gas escapes.


Caution!

Do not spray onto moving or heat-stressed parts such as joints, engine, transmission, driveshaft, exhaust, catalytic converter and brake systems.

Cleaning

  • Splashes and overspray can be removed immediately with gasoline while still fresh.
  • Material that has already dried can only be dissolved with thinner D or thinner R. Caution with fresh paint!

Technical Data


Stone chip protection -AKR 311 KD1 10-

Designation:

  • Stone chip protection -AKR 311 KD1 10-, color black

Product description

Stone chip protection -AKR 311 KD1 10-, color black, is a water-thinnable stone chip protection.

Features:

  • high flexibility
  • can be overpainted with all topcoats
  • is particularly suitable as protection for stone-chip-prone areas on passenger cars and commercial vehicles, such as front sections and door sills

Application information

Substrate

Suitable substrates:

  • properly sanded original or old paint finish (including thermoplastic coatings)
  • primed or surfaced areas


Caution!

Stone chip protection -AKR 311 KD1 10- must not be applied over PVB (acid-curing) adhesion primers.

Pretreatment of substrates:

- Clean thoroughly with silicone remover -LVM 020 000 A5- or long-acting silicone remover -LVM 020 100 A5-.

VW UP. Allgemeine Informationen Lack

- Then sand.

VW UP. Allgemeine Informationen Lack

- Use a suitable cleaner before overcoating to ensure a clean, residue-free surface.

VW UP. Allgemeine Informationen Lack

Processing

Spray equipment:

- Underbody spray gun with screw thread for disposable cans.

VW UP. Allgemeine Informationen Lack

- If a finer surface is desired, stone chip protection -AKR 311 KD1 10- can be applied with a cup gun after appropriate thinning.

Thinner:

- Thinnable with demineralized water -LVW 010 000 A5-

VW UP. Allgemeine Informationen Lack

Application method "High-pressure spraying"

VW UP. Allgemeine Informationen Lack

- Application viscosity 4 mm at +20 °C, DIN 53211

- Set spray pressure (see manufacturer's specifications), 3-4 bar.


Note

Do not thin for high-pressure spraying; supply viscosity equals application viscosity.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

VW UP. Allgemeine Informationen Lack

Application viscosity, 4 mm gravity-feed cup gun "Compliant":

  • Depending on the addition of demineralized water -LVW 010 000 A5-
VW UP. Allgemeine Informationen Lack

Thinner addition of 10 % at +20 °C material temperature

- When adding thinner, use a measuring stick during mixing.

VW UP. Allgemeine Informationen Lack

- Set spray nozzle (see manufacturer's specifications): "Compliant" 1.5-2.0 mm.

- Set spray pressure (see manufacturer's specifications): "Compliant" 2.0–2.5 bar.

VW UP. Allgemeine Informationen Lack

- Apply 2-3 spray passes.

- The recommended dry film thickness is 150-300 µm.

VW UP. Allgemeine Informationen Lack

Drying

Air drying at +20 °C room temperature: up to 150 µm in 2-2.5 hours, and up to 300 µm overnight.

VW UP. Allgemeine Informationen Lack

The final flash-off time with forced drying is at least 35-40 minutes.

VW UP. Allgemeine Informationen Lack

Forced drying at +60 °C object temperature, 150-300 µm: 30 minutes

VW UP. Allgemeine Informationen Lack

Overcoating

Can be overcoated with:

  • Waterborne basecoat and 2K HS clearcoat
  • 2K HS topcoat
VW UP. Allgemeine Informationen Lack

Personal protective equipment:

  • Observe the safety data sheet
  • Wear personal protective equipment during application

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

Guaranteed storage stability is 48 months from the date of production. Use no later than the date stated on the label when stored in sealed original containers at +20 °C.

VW UP. Allgemeine Informationen Lack

Storage conditions

The prescribed storage temperature is +20 ºC (must not fall below +5 ºC).

VW UP. Allgemeine Informationen Lack