Volvo S80 Quiz
Care and Service

Bulb replacement - high beam and low beam cover. Bulb replacement - low beam. Bulb replacement - high beam. Bulb replacement - auxiliary high beam

In this manual: Care and Service
Introduction — 9Safety — 9Instruments and controls — 29Climate control — 12Loading and storage. Storage compartments. Center console. Glove compartment. Center console 12 V socket — 1Loading and storage. Loading. Loading - ski hatch. Roof load. Cargo tie-down eyes — 1Loading and storage. Loading - shopping bag holder*. 12 V socket in luggage compartment* — 1Locks and Alarm System — 14Driver assistance — 33Starting and driving — 29Wheels and tires — 15Care and Service — 24Technical data. Type designations. Weights. Towing weight and nose weight. Engine technical data — 1Technical data. Engine oil - severe operating conditions. Engine oil - quality and capacity. Coolant - quality and capacity. Transmission fluid - quality and capacity — 1Technical Data. Technical data for the air conditioning system. Fuel consumption and CO2 emissions. Tires - approved tire pressure — 1
15steps
~90min
4/5difficulty
Done 0 of 15

The high beam and low beam cover on the Volvo S80 (2nd generation, 2013–2016) must be released to access the bulbs. This section describes removing the cover and handling the clips, as well as the specific steps for replacing the bulbs. The information is supplemented by recommendations for correct reinstallation and notes on safe handling of the different bulb types. This keeps the lighting reliable and fully functional.

Bulb replacement - high beam and low beam cover

The high beam and low beam bulbs are accessed by removing the larger headlight cover.

Lampenwechsel - Abdeckung für Fern- und Abblendlicht

Before starting a bulb replacement, see Bulb replacement - headlight

1. Open the retaining bracket. Press it up/outward to do so. 2. Press down the clips on the cover and remove the cover.

Install the cover in the reverse order.

Related information

- Bulb Replacement - Headlamp

- Bulb replacement - low beam

- Bulb replacement - high beam

- Bulb replacement - auxiliary high beam

Bulb replacement - low beam

The low beam bulb is located inside the larger headlight cover.

CAUTION Applies to vehicles with halogen headlights.

Lampenwechsel - Abblendlicht
  1. Remove the headlight.
  2. Remove the cover.
  3. Disconnect the connector from the bulb.
  4. Release the bulb. To do so, press down the holder.
  5. Insert the new bulb into the socket and let it snap in place. The bulb can only be installed in one way.

Install the individual parts in the reverse order.

Related information

- Bulbs - Technical Data

Bulb replacement - high beam

The high beam bulb is located inside the larger headlight cover.

CAUTION Applies to vehicles with halogen headlights.

Lampenwechsel - Fernlicht
  1. Remove the headlight.
  2. Remove the cover.
  3. Release the bulb. To do so, turn it counterclockwise and then pull it straight out.
  4. Disconnect the connector from the bulb.
  5. Remove the old bulb, insert the new bulb into the socket, turn it clockwise to secure it.

    The bulb can only be installed in one way.

Install the individual parts in the reverse order.

Related information

- Bulbs - Technical Data

Bulb replacement - auxiliary high beam

The auxiliary high beam bulb is located inside the larger headlight cover.

CAUTION Applies to vehicles with xenon headlights*.

Lampenwechsel - extra Fernlicht
  1. Remove the headlight.
  2. Remove the cover.
  3. Release the bulb. To do so, press down the holder.
  4. Disconnect the connector from the bulb.
  5. Insert the new bulb into the socket and let it snap in place. The bulb can only be installed in one way.

Install the individual parts in the reverse order.

Related information

- Bulbs - Technical Data

Replacing the high beam and low beam bulbs on the Volvo S80 (2nd gen) requires removing the larger headlight cover. The bulbs are accessible there and can be replaced by turning or unlocking them. The bulb fits into the socket in only one position.

When handling halogen bulbs, do not touch the glass with bare fingers. Grease residue can shorten the bulb's service life. After replacement, reassemble in the reverse order.

FAQ

Why remove the cover?
This is the only way to access the high beam and low beam bulbs.

When to visit a workshop?
For xenon or LED systems, replacement must be performed by qualified personnel.

Test yourself

A quick Volvo S80 quiz: every answer comes with an explanation and a link to the manual page.