Engine Mechanical System

Troubleshooting

~4min read

Troubleshooting

Engine Misfire With Abnormal Internal Lower Engine Noises.
Suspected Cause Repair
Worn bearings due to shortage orexcessive oil. Replace the crankshaft and connecting rod bearings as required.
Worn piston rings.
(Oil consumption may or may not cause the engine to misfire.)
Compression Pressure Inspection
Repair or replace as required.
Worn crankshaft thrust bearings. Replace the crankshaft and bearings as required.

Engine Misfire With Abnormal Valve Train Noise.
Suspected Cause Repair
Stuck valves.
(Carbon buildup on the valve stem can cause the valve not to close properly.)
Repair or replace as required.
Excessive worn or miss-aligned timing chain. Replace the timing chain and sprocket as required.
Worn camshaft lobes. Replace the camshaft and swing arm.
Swing arm wear. Check and replace swing arm or HLA if necessary.

Engine Misfire With Coolant Consumption
Suspected Cause Repair
Faulty cylinder head gasket and/or cracking or other damage to the cylinder head and engine block cooling system. Inspect the cylinder head and engine block for damage to the coolant passages and/or a faulty head gasket.
Coolant consumption may or may not cause the engine to overheat. Check for coolant leaks and consumption and replace related parts if necessary.

Engine Misfire With Excessive Oil Consumption
Suspected Cause Repair
Wear of valves, valve guides and valve stem seals Repair or replace as required.
Worn piston ring
(Oil consumption may or may not cause the engine to misfire.)
Replace piston, piston ring and cylinder block after checking compression pressure or measuring oil consumption.

Engine Noise On Start-Up, But Only Iasting a Few Seconds.
Suspected Cause Repair
Incorrect oil viscosity. Refill with the correct viscosity oil.
Worn crankshaft thrust bearings. Inspect the crankshaft thrust bearings.
Repair or replace as required.

Upper Engine Noise, Regardless Of Engine Speed.
Suspected Cause Repair
Low oil pressure. Repair or replace as required.
Broken valve spring. Replace the valve spring.
Excessive wear of the outer ring and body of the swing arm bearing. Swing arm assy replace
Stretched or broken timing chain and/or damaged sprocket teeth. Replace the timing chain and sprockets.
Worn timing chain tensioner. Replace the timing chain tensioner as required.
Worn valve or faulty Hydraulic Lash Adjuster (HLA). Replace the valve or HLA.
Worn camshaft lobes. Inspect the camshaft lobes.
Replace camshaft and swing arm if necessary.
Worn valve guides or valve stems. Inspect the valves and valve guides, then repair or replace as required.
Stuck valves.
(Carbon on the valve stem or valve seat may cause the valve to stay open.)
Inspect the valves and valve guides, then repair as required.
Worn drive belt, idler, tensioner and bearings. Replace the drive belt and related parts as required.

Lower engine noise, regardless of engine speed
Suspected Cause Repair
Low oil pressure. Repair or replace as required.
Damaged oil pan, oil pump screen contacts. Inspect the oil pan.
Inspect the oil pump screen.
Repair or replace as required.
Oil pump screen loose, damaged or restricted. Inspect the oil pump screen.
Repair or replace as required.
Excessive piston-to-cylinder bore clearance. Inspect the piston and cylinder bore.
Repair or replace as required.
Excessive piston pin-to-piston clearance. Inspect the piston, piston pin and the connecting rod.
Repair or replace as required.
Excessive connecting rod bearing clearance. Inspect the following components and repair as required.
  • The connecting rod bearings.
  • The connecting rods.
  • Crankshaft
  • The crankshaft pin journal.
Excessive crankshaft bearing clearance. Inspect the following components and repair as required.
  • The crankshaft bearings.
  • The crankshaft journals.
Incorrect piston, piston pin and connecting rod installation. Verify the piston pins and connecting rods are installed correctly.
maintenance as required.

Engine Noise Under Load.
Suspected Cause Repair
Low oil pressure. Repair or replace as required.
Excessive connecting rod bearing clearance. Inspect the following components and repair as required.
  • The connecting rod bearings.
  • The connecting rods.
  • The crankshaft pin journal.
Excessive crankshaft bearing clearance. Inspect the following components and repair as required.
  • The crankshaft bearings.
  • The crankshaft journals.
  • Cylinder Block

Engine will not crank. (crankshaft will not rotate)
Suspected Cause Repair
Hydraulically locked cylinder.
  • Coolant inflow in cylinder.
  • Oil inflow.
  • Excessive fuel inflow.
Remove spark plugs and check for fluid.
  • Inspect cylinder head gasket, head and block for cracks or replace if necessary.
  • Engine oil check and maintenance
  • Check injector open sticking or replace if necessary.
Broken timing chain and/or timing chain sprocket. Inspect timing chain and sprocket.
Repair or replace as required.
Foreign material in cylinder.
  • Broken valve or piston.
  • Inflow of foreign material.
Check for damaged parts and foreign substances
Repair or replace as required.
Seized crankshaft or connecting rod bearings. Inspect crankshaft and connecting rod bearing.
Repair or replace as required.
Bent or broken connecting rod. Inspect connecting rod.
Repair or replace as required.
Broken crankshaft. Inspect crankshaft.
Repair or replace as required.