Engine Mechanical System

Components and Components Location

87steps
~522min
4/5difficulty
010203040503.22N·mlb·ft
Tightening torque found on this page
Done 0 of 87

Contents:

Components and Components Location

Component

Engine Mechanical System — Cooling System / Components and Components Location / Component illustration
1. Cooling Fan Assembly
2. Radiator
3. Radiator Upper Hose
4. Radiator Lower Hose
5. Filler Neck Assembly
6. Radiator Upper Mounting Bracket [RH]
7. Radiator Upper Mounting Bracket [LH]
8. Radiator Lower Mounting Insulator [RH]
9. Radiator Lower Mounting Insulator [LH]

Troubleshooting

Engine Overheat Troubleshooting

Inspection Repair
Visual Inspection Inspect for shortage of coolant in reservoir tank. Reinspect after refilling coolant.
Inspect for coolant pollution after removing radiator cap.
Caution
Be careful when removing pressure cap from overheated vehicle.
Reinspect after replacing coolant.
Inspect for leakage and loose coolant hoses (radiator hose, heater hose, oil cooler hose, etc.). Reinspect for leakage after reinstalling hoses and clamps.
Inspect for leakage on water temperature control assembly mounting part. Reinspect for leakage after replacing O-ring.
Inspect for leakage on water inlet fitting mounting part. Reinspect for leakage after replacing O-ring.
Inspect drive belt (for normal operation of water pump). Adjust or replace drive belt tension
Inspect for leakage on water pump gasket mounting part. Reinspect for leakage after replacing gasket.
Reinspect for leakage after tightening to the specified torque.
Inspect for loose coolant temperature sensor, cooling fan connector and pin. Reinstall loose connector.
Replace relevant part if connector pin is damaged.
Inspect operation status of cooling fan.
- Check operation status by switching ON/OFF the heater control A/C.
Information
Will not operate in cold ambient temperature.
Check mounting status of ground cable.
Diagnostic Device Inspect self-diagnostic code using KDS. Check coolant temperature sensor, wiring, connector, etc.
Component Inspection Inspect water pump impeller. Replace the water pump.

Coolant Replacement

Engine Coolant Refilling And Air Bleeding

Caution
When replenishing coolant, be careful not to spill on the belt, electrical devices.
  1. Make sure the engine and radiator are cool to the touch.
  2. Remove the pressure cap (A).
    Engine Mechanical System — Cooling System / Coolant / Replacement / Engine Coolant Refilling And Air Bleeding illustration
  3. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
  4. Remove the drain plug (A) and drain the coolant.
    Engine Mechanical System — Cooling System / Coolant / Replacement / Engine Coolant Refilling And Air Bleeding illustration
  5. After draining the coolant, re-tighten the drain plug.
  6. Drain coolant and inside the reservoir tank, and then clean it.
  7. Install the coolant refill tank on the radiator and then add the mixture of anti-freeze and water (55 - 60%).
    Caution
    Fill coolant as far as possible with engine and all power supplies shut off.

    Coolant capacity : Approx. 6.0 ℓ (1.58 US gal., 6.34 US qt., 5.27 lmp qt.)

    Note
    • Press the radiator upper/lower hoses to allow air to escape easily.
    • Use only genuine antifreeze.
    • Do not mix antifreeze/coolant from different brands.
    • Do not add any anti-rust.
    • Use only distilled water when mixing antifreeze with water.
    • For best corrosion protection, the coolant concentration must be maintained year-round at 55% minimum. Coolant concentrations less than 55% may not provide sufficient protection against corrosion or freezing.
    • Coolant concentrations greater than 60% will impair cooling efficiency and are not recommended.
  8. Start the engine and run until coolant circulates. When the cooling fan operates and coolant circulates, refill coolant through the reservoir tank.
  9. Repeat step 12 until the cooling fan operates 3 - 5 times and bleed air sufficiently out of the cooling system.
  10. Fill the reservoir tank to the "MAX" (or "FULL") line with coolant and tighten the pressure cap.
  11. Install the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")

Cooling Fan Components and Components Location

Component

Engine Mechanical System — Cooling System / Cooling Fan / Components and Components Location / Component illustration
1. Cooling Fan
1-a. 2.7 - 3,2 N·m (0.28 - 0.33 kgf·m, 2 - 2.4 lb·ft, 24.3 - 28.6 lb·in)
2. Cooling Fan motor
2-a. 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
3. Cooling Fan Shroud
3-a. 4.9 - 7,8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)
4. Cooling Fan Resistor
4-a. 0.2 - 2,5 N·m (0.018 - 0.25 kgf·m, 0.1 - 1.8 lb·ft, 1.6 - 21.7 lb·in)


Cooling Fan Specification

Specification

Item Specification
Fan type PULLER
Fan speed control Resisor
Air volume (m³/h) 1,950 (2,550) - 8% min.
Fan speed (rpm) 1,650 ± 8%
Current consumption (A) 11.7 + 10% max.

Cooling Fan Removal and Installation

Removal

Cooling Fan Assembly
  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the air duct. (Refer to Intake and Exhaust System – "Air Cleaner")
  3. Disconnect resistor connector (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  4. Separate the reservoir tank hose (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  5. Separate the filler neck assembly (A) after removing bolts.

    Tightening torque : 7.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  6. Remove the cooling fan bolts (A).
    Tightening torque : 4.9 - 7,8 N·m (0.5 - 0.8 kgf·m, 3.6 - 5.8 lb·ft, 43.4 - 69.4 lb·in)
    [LH]
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
    [RH]
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  7. Remove the cooling fan assembly (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration

Register

  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the air duct. (Refer to Intake and Exhaust System - "Air Cleaner")
  3. Disconnect resistor connector (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  4. Disconnect the cooling fan motor connector (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration
  5. Remove the resistor (A) after removing bolts.
    Tightening torque : 0.2 - 2,5 N·m (0.018 - 0.25 kgf·m, 0.1 - 1.8 lb·ft, 1.6 - 21.7 lb·in)
    Engine Mechanical System — Cooling System / Cooling Fan / Removal and Installation / Removal illustration

Reassembly

Cooling fan assembly

  1. Install in reverse order of removal.
    Note
    Install the cooling fan to the specified torque.

Register

  1. Install in reverse order of removal.
    Note
    Install the resistor to the specified torque.

Cooling Fan Inspection

Inspection

Fan motor
  1. After connecting the KDS, force the cooling fan motor.
    Information
    There are 2 modes of forced fan motor drive.
    [Fan motor low speed]
    1. Perform the "Fan motor low speed" on the KDS menu. (Forced operation → Engine → Fan motor low speed)
    [Fan motor high speed]
    1. Perform the "Fan motor high speed" on the KDS menu. (Forced operation → Engine → Fan motor high speed)

Cooling Fan Disassembly and Reassembly

Disassembly

  1. Disconnect the cooling fan motor connector (A).
    Engine Mechanical System — Cooling System / Cooling Fan / Disassembly and Reassembly / Disassembly illustration
  2. Remove the cooling fan (A) from the cooling fan shroud.
    Tightening torque : 2.2 - 2,7 N·m (0.22 - 0.28 kgf·m, 1.6 - 2 lb·ft, 19.1 - 24.3 lb·in)
    Engine Mechanical System — Cooling System / Cooling Fan / Disassembly and Reassembly / Disassembly illustration
  3. Remove the cooling fan motor from the cooling fan shroud after removing bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    Engine Mechanical System — Cooling System / Cooling Fan / Disassembly and Reassembly / Disassembly illustration

Reassembly

  1. Install in reverse order of removal.
    Note
    Install the cooling fan motor to the specified torque.

Radiator Removal and Installation

Removal and Installation

  1. Remove the cooling fan. (Refer to Cooling System - "Cooling Fan")
  2. Drain the coolant. (Refer to Cooling System - "Coolant")
  3. Separate the radiator upper hose (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  4. Separate the radiator lower hose (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  5. Separate the IVTF cooler hoses (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  6. Remove the front bumper assembly. (Refer to Body - "Front Bumper Assembly")
  7. Remove the LH radiator upper mounting bracket bolt (A).

    Tightening torque : 7.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  8. Remove the RH radiator upper mounting bracket (A) after removing RH radiator upper mounting bracket bolt.

    Tightening torque : 7.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  9. Disconnect the ambient temperature sensor connector (A).
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  10. Remove the upper air guard (A) after removing bolts.
    Tightening torque : 3.9 - 5,9 N·m (0.4 - 0.6 kgf·m, 2.9 - 4.3 lb·ft, 34.7 - 52.1 lb·in)
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  11. Remove the lower air guard (A), after removing the fastener. [LH]
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
    [RH]
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  12. Separate the conditioner (A).
    Note
    Be careful not to damage the air conditioner system when the condenser is separated.
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration
  13. Remove the radiator (A).
    Engine Mechanical System — Cooling System / Radiator / Removal and Installation illustration

Installation

  1. Install in reverse order of removal.
    Note
    Install the radiator to the specified torque.
  2. Fill the coolant. (Refer to Cooling System - "Coolant")
  3. Start engine and check for leaks.

Radiator Inspection

Inspection

Radiator Leakage
  1. Wait until engine is cool, then carefully remove the pressure cap and fill the radiator with engine coolant, then install it on the pressure tester.
    Engine Mechanical System — Cooling System / Radiator / Inspection illustration
  2. Pressurize the pressure of the pressure tester to about 93 - 122 kPa (0.95 - 1.25 kg/cm², 13 - 17 psi)
  3. Inspect for engine coolant leaks and a drop in pressure
  4. Remove the tester and reinstall the pressure cap.
    Note
    Check for engine oil in the coolant and/or coolant in the engine oil.

Water Temperature Control Assembly Components and Components Location

Component

Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Components and Components Location / Component illustration
1. Water Temperature Control Assembly
1-a. 9.8 - 11,8 N·m
2. Bypass Hose
3. Heater Pipe & Hose Assembly
3-a. 19.6 - 24 N·m

Water Temperature Control Assembly Removal and Installation

Removal

Water temperature control assembly
  1. Disconnect the battery negative ( - ) terminal.
  2. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
  3. Drain the engine coolant. (Refer to Cooling System - "Coolant")
  4. Remove the air cleaner assembly. (Refer to Intake and Exhaust System - "Air Cleaner")
  5. Separate the radiator upper hose (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  6. Release the clamp, and then disconnect the heater hose (A).
    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  7. Separate the bypass hose (A) releasing the clamp.
    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  8. Disconnect the Engine Coolant Temperature Sensor (ECTS) and Purge Control Solenoid Valve (PCSV).
    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  9. Remove the water temperature control assembly (A) after removing bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
    Note
    • Do not reuse the water temperature control assembly O-ring.
    • Clean the contact surfaces before assembling the water temperature control assembly.
  10. Drain the engine coolant. (Refer to Cooling System - "Coolant")
  11. Remove the air cleaner assembly. (Refer to Intake and Exhaust System - "Air Cleaner")
  12. Remove the intake manifold. (Refer to Intake and Exhaust System - "Intake Manifold")
  13. Remove the heater pipe bolt (B) and separate heater pipe hoses (A) after releasing the clamp.

    Tightening torque : 19.6 - 24 N·m

    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  14. Separate the heater hose (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
  15. Remove the heater pipe (A) after removing bolt.

    Tightening torque : 19.6 - 24 N·m

    Engine Mechanical System — Cooling System / Water Temperature Control Assembly / Removal and Installation / Removal illustration
Heating Pipe

Installation

Water temperature control assembly

  1. Install in reverse order of removal.
    Note
    Install the water temperature control assembly to the specified torque.
  2. Fill the engine coolant. (Refer to Cooling System - "Coolant")
  3. Start engine and check for leaks.
  4. Recheck engine coolant level.

Heating Pipe

  1. Install in reverse order of removal.
    Note
    Install the heater pipe to the specified torque.
  2. Fill the engine coolant. (Refer to Cooling System - "Coolant")
  3. Start engine and check for leaks.
  4. Recheck engine coolant level.

Water Inlet Fitting Components and Components Location

Component

Engine Mechanical System — Cooling System / Water Inlet Fitting / Components and Components Location / Component illustration
1. Water Inlet Fitting
1-a. 18.6 - 24 N·m
2. Thermostat

Water Inlet Fitting Removal and Installation

Removal

  1. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
  2. Drain the coolant. (Refer to Cooling System - "Coolant")
  3. Separate the radiator lower hose (A) after releasing the clamp.
    Engine Mechanical System — Cooling System / Water Inlet Fitting / Removal and Installation / Removal illustration
  4. Remove the water inlet fitting (A) after removing the nuts.

    Tightening torque : 18.6 - 24 N·m

    Engine Mechanical System — Cooling System / Water Inlet Fitting / Removal and Installation / Removal illustration
  5. Remove the thermostat (A).
    Engine Mechanical System — Cooling System / Water Inlet Fitting / Removal and Installation / Removal illustration
  6. Install in reverse order of removal.
    Note
    Install the water inlet fitting to the specified torque.
  7. Fill the coolant. (Refer to Cooling System - "Coolant")
  8. Start engine and check for leaks.
  9. Recheck engine coolant level.
Installation

Water Pump Components and Components Location

Component

Engine Mechanical System — Cooling System / Water Pump / Components and Components Location / Component illustration
1. Water Pump Pulley
1-a. 9.8 - 11,8 N·m
2. Water Pump
2-a. 9.8 - 11,8 N·m
3. Water Pump Gasket

Water Pump Troubleshooting

Troubleshooting

Coolant leakage
Symptom How to inspect Repair
Leak hole Visually check Check leaks after about ten-minute warming up.
  • Replace water pump in case of leak.
  • If there are no leaks, reuse the water pump. (Do not change the water pump)
    Information
    Evaporation deposits due to the evaporation of microscopic water vapor or traces of evaporation of traces of coolant occur even during normal operation of the water pump. - Remove the sediment from each pore and recheck for leaks.
Gasket or bolt part leak Check water pump mounting bolt tightness. Tighten the water pump mounting bolts to the specified torque.
Check for gasket damage or dust ingress Replace the gasket and clean dust off.
Water Pump External Surface Leakage Check the water pump for cracks. Replace water pump in case of cracks.

Noise
Symptom How to inspect Repair
  • Bearing noise
  • Mechanical seal high frequency
  • Impeller interference
Check the use of a stethoscope After starting the engine, check noise with a stethoscope.
  • If there is no noise, reuse the water pump (do not replace it).
  • If there is any noise from the water pump, remove the drive belt and recheck. (Replace the water pump if noise occurs even after removal)
Inspection after removing a drive belt After removing a drive belt, check noise again.
  • Drive Reuse of water pump in case of noise from drive
  • If there is no noise, replace the water pump with a new one.
Inspection after removing a water pump Check water pump body & impeller interference Replace water pump in case of interference

Overheat
Symptom How to inspect Repair
  • Impeller interference
  • Loosened impeller
Inspection after removing a water pump Corrosion of the impeller wing
  • Check engine coolant.
  • Poor coolant quality / Maintenance check
Remove the impeller from the shaft Replace the water pump.

Water Pump Removal and Installation

Removal

  1. Remove the engine room under cover. (Refer to Engine and Transaxle Assembly - "Engine Room Under Cover")
  2. Drain the coolant. (Refer to Cooling System - "Coolant")
  3. Remove the drive belt. (Refer to Drive Belt System - "Drive Belt")
  4. Remove the water pump pulley (A), after removing the bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Water Pump / Removal and Installation / Removal illustration
  5. Remove the water pump (A) with gasket after removing bolts.

    Tightening torque : 9.8 - 11,8 N·m

    Engine Mechanical System — Cooling System / Water Pump / Removal and Installation / Removal illustration
  6. Install in reverse order of removal.
    Note
    Install the water pump to the specified torque.
  7. Fill the coolant. (Refer to Cooling System - "Coolant")
  8. Start engine and check for leaks.
  9. Recheck engine coolant level.
Installation