Body Exterior, Doors, Roof & Vehicle Security

B210f Interlock/pn on Circ

12steps
~72min
3/5difficulty
Done 0 of 12
DTC Description

IPDM E/R confirms the shift position with the following signals:

  • Transmission range switch

  • Shift position signal from BCM (CAN)

DTC DETECTION LOGIC

DTC No.CONSULT screen terms (Trouble diagnosis content)DTC Detection Condition
B210F

INTERLOCK/PN ON CIRC

(Interlock/park neutral switch on circuit)
Diagnosis condition When ignition switch ON.
Signal (terminal) —
Threshold

IPDM E/R detects a mismatch between the signals below for 1 second or more:

  • Transmission range switch input signal

  • Shift position signal from BCM (CAN)

Diagnosis delay time —

POSSIBLE CAUSE

  • Transmission range switch

  • Harness or connector

  • Transmission range switch circuit is open or shorted.

  • IPDM E/R

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Ignition switch ON under the following conditions and wait for at least 1 second:

    • CVT selector lever is in the P (Park) or N (Neutral) position.

    • Do not depress the brake pedal.

  2. Select “Self Diagnostic Result” mode of “IPDM E/R”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK DTC WITH BCM

Refer to DTC Index.

Is the inspection result normal?

YES>>

GO TO 2.

NO>>

Repair or replace malfunctioning parts.

CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between IPDM E/R harness connector and ground under following condition:

    IPDM E/R—Condition

    Voltage

    (Approx.)
    ConnectorTerminal
    E119 37 Ground CVT selector lever P (Park) or N (Neutral) Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK TRANSMISSION RANGE SWITCH CIRCUIT FOR CONTINUITY

  1. Ignition switch OFF.

  2. Check continuity between IPDM E/R harness connector.

    IPDM E/RConditionContinuity
    ConnectorTerminals
    F24 63 66 Transmission range switch P or N Yes
    Other No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 5.

CHECK TRANSMISSION RANGE SWITCH CIRCUIT FOR SHORT

  1. Disconnect IPDM E/R connector.

  2. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R—Continuity
    ConnectorTerminal
    F24 63 Ground No
    66

Is the inspection result normal?

YES>>

Replace the IPDM E/R. Refer to Removal and Installation.

NO>>

Repair or replace harness.

CHECK TRANSMISSION RANGE SWITCH INPUT SIGNAL CIRCUIT

  1. Disconnect transmission range switch harness connector and IPDM E/R harness connector.

  2. Check continuity between transmission range switch and IPDM E/R harness connectors.

    Transmission range switchIPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    F29 7 F24 63 Yes
    10 66
  3. Check continuity between transmission range switch harness connector and ground.

    Transmission range switch—Continuity
    ConnectorTerminal
    F29 7 Ground No
    10

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK TRANSMISSION RANGE SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Replace transmission range switch. Refer to Removal and Installation.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.