Body Exterior, Doors, Roof & Vehicle Security

B2601 Shift Position

23steps
~138min
4/5difficulty
Done 0 of 23
DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen terms (Trouble diagnosis content)DTC Detection Condition
B2601

SHIFT POSITION

(Shift position)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold When there is a difference between P (Park) range signal from CVT shift selector (detent switch) and P (Park) position signal from IPDM E/R (CAN)
Diagnosis delay time —

POSSIBLE CAUSE

  • CVT shift selector (detent switch)

  • BCM

  • Harness or connector

    (The CAN communication line is open or shorted.)

  • Harness or connector

    [CVT shift selector (detent switch) circuit is open or shorted.]

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Shift the selector lever to the P (Park) position.

  2. Ignition switch ON and wait 2 seconds or more.

  3. Shift the selector lever to any position other than P (Park) and wait 2 seconds or more.

  4. Select “Self Diagnostic Result” mode of “BCM”.

  5. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK CVT SHIFT SELECTOR FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “DETE/CANCL SW” and “DETE SW - IPDM” in “Data Monitor” mode of “BCM(INTELLIGENT KEY)”.

  3. Check “DETE/CANCL SW” and “DETE SW - IPDM” indication under the following conditions:

    Monitor itemConditionIndication
    DETE/CANCL SW CVT Shift selector In any position other than P (Park) ON
    P (Park) OFF
    DETE SW - IPDM CVT Shift selector In any position other than P (Park) ON
    P (Park) OFF

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

If “DETE/CANCL SW” function is incorrect. GO TO 2.

NO>>

If “DETE SW - IPDM” function is incorrect. GO TO 5.

CHECK CVT SHIFT SELECTOR CIRCUIT (BCM)

  1. Disconnect CVT shift selector (detent switch) connector and IPDM E/R connector.

  2. Check continuity between CVT shift selector (detent switch) harness connector and BCM harness connector.

    CVT shift selector (detent switch)BCMContinuity
    ConnectorTerminalConnectorTerminal
    M78 6 M18 20 Yes
  3. Check continuity between CVT shift selector (detent switch) harness connector and ground.

    CVT shift selector (detent switch) Ground Continuity
    Connector Terminal
    M78 6 No

Is the inspection result normal?

YES>>

GO TO 3.

NO>>

Repair or replace harness.

CONNECTOR INSPECTION

  1. Disconnect BCM connector.

  2. Check connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace as necessary.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

CHECK CVT SHIFT SELECTOR CIRCUIT (IPDM E/R)

  1. Disconnect BCM connector M18, IPDM E/R connector and CVT shift selector (detent switch) connector.

  2. Check continuity between CVT shift selector (detent switch) harness connector and IPDM E/R harness connector.

    CVT shift selector (detent switch)IPDM E/RContinuity
    ConnectorTerminalConnectorTerminal
    M78 6 E119 31 Yes
  3. Check continuity between CVT shift selector (detent switch) harness connector and ground.

    CVT shift selector (detent switch)—Continuity
    ConnectorTerminal
    M78 6 Ground No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CONNECTOR INSPECTION

  1. Disconnect IPDM E/R connector.

  2. Check connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 7.

NO>>

Repair or replace as necessary.

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

>>

Inspection End.

Component Inspection

CHECK CVT SHIFT SELECTOR (DETENT SWITCH)

  1. Ignition switch OFF.

  2. Disconnect CVT shift selector (detent switch) connector.

  3. Check continuity between CVT shift selector (detent switch) terminals.

    CVT shift selector (detent switch)ConditionContinuity
    Terminal
    5 6 Selector lever P (Park) position No
    Other than above Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace CVT shift selector. Refer to Removal and Installation.