Body Exterior, Doors, Roof & Vehicle Security

B2604 Pnp/clutch Sw

20steps
~120min
4/5difficulty
Done 0 of 20
DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen terms (Trouble diagnosis content)DTC Detection Condition
B2604

PNP/CLUTCH SW

(Park neutral position/clutch switch)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold

The following states are detected for 5 seconds while ignition switch is ON:

  • P/N position signal is sent from TCM but shift position signal input (CAN) from TCM is other than P (Park) and N (Neutral)

  • P/N position signal is not sent from TCM but shift position signal input (CAN) from TCM is P (Park) or N (Neutral)

Diagnosis delay time —

POSSIBLE CAUSE

  • Harness or connectors

    (CAN communication line is open or shorted.)

  • BCM

  • TCM

  • Harness or connector

    (TCM circuit is open or shorted.)

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Shift the selector lever to the P (Park) position.

  2. Ignition switch ON and wait 5 seconds or more.

  3. Shift the selector lever to the N (Neutral) position and wait 5 seconds or more.

  4. Shift the selector lever to any position other than P (Park) and N (Neutral) and wait 5 seconds or more.

  5. Select “Self Diagnostic Result” mode of “BCM”.

  6. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK TRANSMISSION RANGE FUNCTION

  1. Ignition switch ON.

  2. Select “SFT P -MET”, “SFT N -MET” and "SFT PN/N SW" in "Data Monitor" mode of "BCM(INTELLIGENT KEY)".

  3. Check “SFT P -MET”, “SFT N -MET” and “SFT PN/N SW” indication under the following conditions:

    Monitor itemConditionIndication
    SFT P -MET CVT Shift selector Selector lever is in any position except the P (Park) position OFF
    Selector lever is in the P (Park) position ON
    SFT N -MET CVT Shift selector Selector lever is in any position except the N (Neutral) position OFF
    Selector lever is in the N (Neutral) position ON
    SFT PN/N SW CVT Shift selector Selector lever is in and position except the P (Park) or N (Neutral) position OFF
    Selector lever is in the P (Park) or N (Neutral) position ON

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

If “SFT N -MET” or “SFT P -MET” is incorrect. GO TO 7.

NO>>

If “SFT PN/N SW” is incorrect. GO TO 2.

CHECK DTC OF TCM

CONSULT

Select “Self Diagnostic Result” mode of “TRANSMISSION”.

Is DTC detected?

YES>>

Perform the trouble diagnosis related to the detected DTC. Refer to DTC Index.

NO>>

GO TO 3.

CHECK BCM INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between BCM harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M18 39 Ground Selector lever P (Park) or N (Neutral) position Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

GO TO 5.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

CHECK BCM INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect transmission range switch connector, BCM connector and ECM connector F79.

  3. Check continuity between transmission range switch harness connector and BCM harness connector.

    Transmission range switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    F29 10 M18 39 Yes
  4. Check continuity between transmission range switch harness connector and ground.

    Transmission range switch Ground Continuity
    Connector Terminal
    F29 10 No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

CHECK TRANSMISSION RANGE SWITCH FUNCTION (METER)

CONSULT

  1. Ignition switch ON.

  2. Select “SHIFT IND” in “Data Monitor” mode of “METER_M&A”.

  3. Check “SHIFT IND” indication under the following conditions:

    Monitor itemConditionIndication
    SHIFT IND CVT Shift selector P (Park) position P
    N (Neutral) position N

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Refer to Inspection.