Body Exterior, Doors, Roof & Vehicle Security

B2555 Stop Lamp

20steps
~120min
4/5difficulty
Done 0 of 20
DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen terms (Trouble diagnosis content)DTC Detection Condition
B2555

STOP LAMP

(Stop lamp)
Diagnosis condition When ignition switch ON.
Signal (terminal) —
Threshold BCM makes a comparison between the upper voltage and lower voltage of stop lamp switch. It judges from their values to detect the malfunctioning circuit
Diagnosis delay time —

POSSIBLE CAUSE

  • Stop lamp switch

  • Fuse

  • BCM

  • Harness or connector

    (Stop lamp switch circuit is open or shorted.)

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Depress the brake pedal and wait 1 second or more.

  2. Select “Self Diagnostic Result” mode of “BCM”.

  3. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK BRAKE SWITCH FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “BRAKE SW1” and “BRAKE SW2” in “Data Monitor” mode of “BCM(INTELLIGENT KEY)”.

  3. Check “BRAKE SW1” and “BRAKE SW2” indication under the following conditions:

    Monitor itemConditionIndication
    BRAKE SW1 Brake pedal Depressed OFF
    Released ON
    BRAKE SW2 Brake pedal Depressed ON
    Released OFF

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

If “BRAKE SW1” is incorrect. GO TO 2.

NO>>

If “BRAKE SW2” is incorrect. GO TO 3.

CHECK STOP LAMP SWITCH INPUT SIGNAL 1

  1. Ignition switch OFF.

  2. Disconnect BCM connector.

  3. Check voltage between BCM harness connector and ground.

    (+)(–)

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M18 25 Ground Battery voltage

Is the inspection normal?

YES>>

GO TO 7.

NO>>

Check 10 A fuse [No. 10, located in the fuse block (J/B)].

NO>>

Check harness for open or short between BCM and fuse.

CHECK STOP LAMP SWITCH INPUT SIGNAL 2

  1. Disconnect BCM connector.

  2. Check voltage between BCM harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M18 27 Ground Brake pedal Depressed Battery voltage
    Not depressed 0 V

Is the inspecting result normal?

YES>>

GO TO 7.

NO>>

GO TO 4.

CHECK STOP LAMP SWITCH POWER SUPPLY CIRCUIT

  1. Disconnect stop lamp switch connector.

  2. Check voltage between stop lamp switch harness connector and ground.

    (+)(–)

    Voltage

    (Approx.)
    Stop lamp switch
    ConnectorTerminal
    E38 1 Ground Battery voltage

Is the inspection result normal?

YES>>

GO TO 5.

NO>>

Check harness for open or short between stop lamp switch and fuse.

CHECK STOP LAMP SWITCH CIRCUIT

  1. Check continuity between stop lamp switch harness connector and BCM harness connector.

    Stop lamp switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    E38 2 M18 27 Yes
  2. Check continuity between stop lamp switch harness connector and ground.

    Stop lamp switch Ground Continuity
    Connector Terminal
    E38 2 No

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

Repair or replace harness.

CHECK STOP LAMP SWITCH

Refer to Component Inspection.

Is the inspection result normal?

YES>>

GO TO 9.

NO>>

Replace stop lamp switch. Refer to Exploded View.

CONNECTOR INSPECTION

Check BCM connectors and terminals for deformation, disconnection, looseness or damage.

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace as necessary.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.

Component Inspection

CHECK STOP LAMP SWITCH

  1. Ignition switch OFF.

  2. Disconnect stop lamp switch connector.

  3. Check continuity between stop lamp switch terminals.

    Stop lamp switchConditionContinuity
    Terminal
    1 2 Brake pedal Not depressed No
    Depressed Yes

Is the inspection result normal?

YES>>

Inspection End.

NO>>

Replace stop lamp switch. Refer to Exploded View.