Body Exterior, Doors, Roof & Vehicle Security

B2605 Pnp/clutch Sw

23steps
~138min
4/5difficulty
Done 0 of 23
DTC Description

DTC DETECTION LOGIC

DTC No.CONSULT screen terms (Trouble diagnosis content)DTC Detection Condition
B2605

PNP/CLUTCH SW

(Park neutral position/clutch switch)
Diagnosis condition When ignition switch is ON.
Signal (terminal) —
Threshold When ignition switch is ON, P/N position signal input from TCM and P/N position signal (CAN) input from IPDM E/R do not match
Diagnosis delay time —

POSSIBLE CAUSE

  • IPDM E/R

  • BCM

  • Harness or connectors

    (TCM circuit is open or shorted.)

  • Harness or connector

    (The CAN communication line is open or shorted.)

FAIL-SAFE

—

DTC Confirmation Procedure

PERFORM DTC CONFIRMATION PROCEDURE

CONSULT

  1. Shift the selector lever to the P (Park) position.

  2. Ignition switch ON and wait 1 second or more.

  3. Shift the selector lever to the N (Neutral) position and wait 1 second or more.

  4. Shift the selector lever to any position other than P (Park) and N (Neutral) and wait 1 second or more.

  5. Select “Self Diagnostic Result” mode of “BCM”.

  6. Check DTC.

Is DTC detected?

YES>>

Refer to Diagnosis Procedure.

NO>>

Inspection End.

Diagnosis Procedure

CHECK TRANSMISSION RANGE SWITCH FUNCTION

CONSULT

  1. Ignition switch ON.

  2. Select “SFT PN-IPDM” and “SFT PN/N SW” in “Data Monitor” mode of “BCM(INTELLIGENT KEY)”.

  3. Check “SFT PN-IPDM” and “SFT PN/N SW” indication under the following conditions:

    Monitor itemConditionIndication
    SFT PN-IPDM CVT Shift selector Any position other than P (Park) or N (Neutral) position OFF
    P (Park) or N (Neutral) position ON
    SFT PN/N SW CVT Shift selector Any position other than P (Park) or N (Neutral) position OFF
    P (Park) or N (Neutral) position ON

Is the inspection result normal?

YES>>

Refer to Intermittent Incident.

NO>>

If “SFT PN-IPDM” is incorrect. GO TO 2.

NO>>

If “SFT PN/N SW” is incorrect. GO TO 5.

CHECK IPDM E/R INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between IPDM E/R harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    IPDM E/R
    ConnectorTerminal
    F24 66 Ground Selector lever P (Park) or N (Neutral) position Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

Replace IPDM E/R. Refer to Removal and Installation.

NO>>

GO TO 3.

CHECK IPDM E/R INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect transmission range switch connector and IPDM E/R connector.

  3. Check continuity between IPDM E/R harness connector and transmission range switch harness connector.

    IPDM E/RTransmission range switchContinuity
    ConnectorTerminalConnectorTerminal
    E119 37 F29 10 Yes
  4. Check continuity between IPDM E/R harness connector and ground.

    IPDM E/R Ground Continuity
    Connector Terminal
    E119 37 No

Is the inspection result normal?

YES>>

GO TO 4.

NO>>

Repair or replace harness.

REPLACE IPDM E/R

Replace IPDM E/R. Refer to Removal and Installation.

>>

Inspection End.

CHECK BCM INPUT SIGNAL

  1. Ignition switch ON.

  2. Check voltage between BCM harness connector and ground.

    (+)(–)Condition

    Voltage

    (Approx.)
    BCM
    ConnectorTerminal
    M18 39 Ground Selector lever P (Park) or N (Neutral) position Battery voltage
    Other than above 0 V

Is the inspection result normal?

YES>>

GO TO 6.

NO>>

GO TO 7.

REPLACE BCM

  1. Replace BCM. Refer to Removal and Installation.

  2. Perform initialization of BCM and registration of all Intelligent Keys. Refer to Work Procedure.

>>

Inspection End.

CHECK BCM INPUT SIGNAL CIRCUIT

  1. Ignition switch OFF.

  2. Disconnect transmission range switch connector, BCM connector and ECM connector F79.

  3. Check continuity between transmission range switch harness connector and BCM harness connector.

    Transmission range switchBCMContinuity
    ConnectorTerminalConnectorTerminal
    F29 10 M18 39 Yes
  4. Check continuity between transmission range switch harness connector and ground.

    Transmission range switch Ground Continuity
    Connector Terminal
    F29 10 No

Is the inspection result normal?

YES>>

GO TO 8.

NO>>

Repair or replace harness.

CHECK INTERMITTENT INCIDENT

Refer to Intermittent Incident.

>>

Inspection End.