Precautions
PRECAUTION
FUEL GAUGE OPERATION
(a) Operation
The combination meter assembly uses the fuel injection volume signal sent from the ECM and the fuel level sensor assembly to detect the amount of fuel remaining in the fuel tank assembly. Each gauge assembly has a variable resistor whose resistance changes according to the amount of fuel remaining. The gauge assemblies receive voltage from the combination meter assembly and change the voltage according to this resistance, which varies with the amount of fuel remaining in the fuel tank assembly. The combination meter assembly receives the fuel injection volume signal from the ECM, detects the voltage between each resistor and each variable resistor in the combination meter assembly, and operates the fuel gauge.
(b) FUEL GAUGE READING
(1) During normal driving:
Because the fuel level in the fuel tank assembly changes when driving on inclines or when braking, the fuel gauge is updated based on the fuel injection volume value during normal driving. However, because the fuel injection volume has a margin of error, the value is displayed after correction using input values from the fuel level sensor assembly.
(2) When refueling:
The fuel level in the fuel tank rises quickly when fuel is added. If the averaging process used during normal driving were applied in this case, the fuel gauge value could not be updated quickly. Therefore, when it is determined that fuel has been added to the vehicle based on the shift lever position and changes in the fuel level, the output values of the fuel level sensor assembly are immediately reflected in the fuel gauge value. This control is called the refill limit.
(c) REFILL LIMIT CONDITIONS
NOTICE:
Refuel with the ignition switch in the OFF position for safety, and to establish the refill limit so that an appropriate fuel gauge value is obtained. If it is necessary to refuel with the ignition switch in the ON position, stop the vehicle.
(1) Normal state estimation result (when normal refilling is used for refueling)
With the ignition switch in the OFF position, the fuel level sensor assembly detects a change in fuel level of at least 5.0 liters (5.3 US qt, 4.4 Imp. qt).
(2) Other limit conditions (when using other means for refueling)
One of the following conditions is met
- With the vehicle and engine stopped and the ignition switch in the ON position, the fuel level sensor assembly detects a change in fuel level of at least 5.0 liters (5.3 US qt, 4.4 Imp. qt).
- With the vehicle stopped, the engine running, the ignition switch in the ON position and the shift lever in P or N, the fuel level sensor assembly detects a change in fuel level of at least 5.0 liters (5.3 US qt, 4.4 Imp. qt).
- With the vehicle stopped, the engine running, the ignition switch in the ON position and the shift lever in a driving position, the fuel level sensor assembly detects a change in fuel level of at least 15.0 liters (15.9 US qt, 13.2 Imp. qt).
(d) PRECAUTIONS FOR REFILLING
The fuel level sensor assembly cannot detect fuel level changes in certain areas (around points E and F). Therefore, even if at least 5.0 liters (5.3 US qt, 4.4 Imp. qt) of fuel is added, the refueling evaluation may not be completed, and the fuel gauge reading may not change when the fuel level is within such ranges.
(e) FORCED FUEL GAUGE RESET
When the vehicle is driven at or above 1.8 km/h, if the output values of the fuel level sensor assembly differ from the fuel gauge value by at least 15.0 liters (15.9 US qt, 13.2 Imp. qt) for approximately 2 minutes, the output values of both sensor assemblies are immediately reflected in the fuel gauge value to correct the reading when the refill evaluation cannot be completed.
CAUTION / NOTICE FOR REPLACING INSTRUMENT CLUSTER ASSEMBLY
(a) When replacing the instrument cluster assembly, replace it with a new part. If an instrument cluster assembly installed in another vehicle is used, the recorded information will not match the information transmitted by the vehicle, and a DTC may be stored.
IGNITION SWITCH TERMS
HINT:
The type of ignition switch used varies depending on vehicle specifications. The terms listed in the table below are used in this section.
Term | Ignition Switch (Position) | Engine Switch (Condition) |
|---|---|---|
Ignition Switch in OFF position |
LOCK |
OFF (Locked) |
Ignition Switch in ACC position |
ACC |
ON (ACC) |
Ignition Switch in ON position |
ON |
ON (IG) |
Starting the engine |
START |
ON (Starting) |
TIRE PRESSURE WARNING ECU AND RECEIVER TERMS
HINT:
The type of tire pressure detection ECU and receiver used on this model varies depending on vehicle specifications. The terms listed in the table below are used in this section.
Vehicle Specifications | Part Reference in Manual | Actual Part Reference |
|---|---|---|
without Smart Key System |
Tire pressure warning ECU and receiver |
Door control receiver and tire pressure warning system receiver assembly. |
with Smart Key System |
Electronic Key and TPMS Receiver Assembly |