Meters / Gauges / Display

Inspection On Vehicle

~5min read

INSPECTION ON VEHICLE

PROCEDURE

1. CHECK INSTRUMENT CLUSTER ASSEMBLY

(a) Check speedometer operation

NOTICE:

  • The combination meter receives the vehicle speed signal transmitted by the skid control ECU (brake actuator assembly) via the CAN communication line. Therefore, perform the following check by referring to the values shown on the Data List of the skid control ECU (brake actuator assembly), as it is the source of the vehicle speed signal.
  • The values on the Data List of the skid control ECU (brake actuator assembly) are used for this check. Therefore, be sure to perform the check after confirming that no DTC is output.
  • If the tire size or tire inflation pressure is not within the specified range, or if the tires are excessively worn, the speedometer error indication will increase. Therefore, be sure to perform this check after confirming that the tire size, tire pressure and tire wear are within the specified ranges.

(1) Warm up the engine.

(2) Connect the Techstream to the DLC3.

(3) Turn the ignition switch to the ON position.

(4) Turn on the Techstream.

(5) Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.

(6) Read the Data List by following the Techstream instructions.

Chassis > ABS/VSC/TRAC/EPB > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed

Maximum value for wheel speed sensor

Min.: 0 km/h, Max.: 326 km/h

Vehicle stopped: 0 km/h

When vehicle is driving at constant speed: No large fluctuation

Chassis > ABS/VSC/TRAC/EPB > Data List

Vehicle Speed

Reference km/h (without occupant classification system)

Techstream indication (km/h)

Acceptable range (km/h)

20

21,0 à 25,0

40

41,7 à 46,2

60

62,7 à 67,2

80

83,4 à 88,4

100

104,3 à 109,3

120

125,1 à 130,6

140

145,8 à 151,8

160

166,2 à 173,2

180

186,9 à 194,5

200

207,7 à 215,7

220

228,4 à 236,8

Reference km/h (with occupant classification system and without daytime running lights off function)

Techstream indication (km/h)

Acceptable range (km/h)

20

18,5 à 22,5

40

38,7 à 43,2

60

59,2 à 63,7

80

79,3 à 84,3

100

99,8 à 104,8

120

120,3 à 125,3

140

140,7 à 145,7

160

161,2 à 166,2

180

181,6 à 186,6

200

202,1 à 207,1

220

222,6 à 227,6

Reference km/h (with occupant classification system and with daytime running lights deactivation function)

Techstream indication (MI/H)

Acceptable range (MI/H)

20

19,3 à 21,8

40

39,5 à 42,3

60

60 à 62,8

80

80,2 à 83,4

100

100,7 à 103,9

120

121,2 à 124,4

140

141,6 à 144,8

OK:

The speedometer value is within the acceptable speed range for each vehicle speed.

(b) Check tachometer

(1) Warm up the engine.

(2) Connect the Techstream to the DLC3.

(3) Turn the ignition switch to the ON position.

(4) Turn on the Techstream.

(5) Select the following menus: Powertrain / Engine and ECT / Data List.

(6) Read the Data List by following the Techstream instructions.

Powertrain > Engine and ECT > Data List

Tester display

Item

Range

Normal Condition

Reference value

Diagnostic Note

Engine Speed

Engine speed

Min.: 0 rpm, Max.: 16,383 rpm

710 to 810 rpm: At idle, engine warm

-

If the crankshaft position sensor malfunctions, "Engine Speed" is approximately 0 rpm or fluctuates significantly from the actual engine speed

Powertrain > Engine and ECT > Data List

Engine Speed

Reference

Techstream indication (rpm)

Acceptable range (rpm)

Data in parentheses is for reference only.

700

630 à 770

1 000

(900 à 1 100)

2 000

(1 850 à 2 150)

3 000

2 800 à 3 200

4 000

(3 800 à 4 200)

5 000

4 800 à 5 200

6 000

(5 750 à 6 250)

7 000

6 700 à 7 300

8 000

(7 700 à 8 300)

OK:

The tachometer value is within the acceptable speed range for each engine speed.

(c) Check LED illumination (LED check)

(1) Check the illumination function of the warning lights or indicators listed below when the ignition switch is turned ON.

OK:

Warning light or indicator

Control ECU

Specified Condition

Brake Warning Light

Skid control ECU (brake actuator assembly)

The warning light or indicator illuminates for approximately 3 seconds after the ignition switch is turned ON.

VSC OFF Warning Light

Skid control ECU (brake actuator assembly)

Skid Control Warning Light

Skid control ECU (brake actuator assembly)

ABS Warning Light

Skid control ECU (brake actuator assembly)

Low tire pressure warning light

Tire pressure warning ECU and receiver

EPB indicator

Skid control ECU (brake actuator assembly)

EPB indicator

Skid control ECU (brake actuator assembly)

AHB Indicator*1

Main body ECU (multiplex network body ECU)

BSM Indicator*2

Left blind spot monitor sensor

RCTA Indicator*2

Left blind spot monitor sensor

SRS warning light

Airbag sensor assembly

The indicator illuminates for approximately 6 seconds after the ignition switch is turned ON.

Charge warning light

ECM

The warning light illuminates when the ignition switch is turned ON.

MIL (malfunction indicator lamp)

ECM

EPS warning light

Power steering ECU assembly

  • *1: with Toyota Safety Sense P system
  • *2: With blind spot monitor system