Meters / Gauges / Display

Vehicle speed signal circuit

~13min read

DESCRIPTION

The instrument cluster assembly receives the vehicle speed signal through this circuit. The wheel speed sensors generate a voltage that varies with vehicle speed. The output of the wheel speed sensors is received by the skid control ECU (brake actuator assembly), which uses this information to create the vehicle speed signal*a. The vehicle speed signal consists of pulses sent to the instrument cluster assembly by the skid control ECU (brake actuator assembly). To create this signal, a 12 V voltage is supplied from IG2 through a resistor in the instrument cluster assembly. This voltage is sent to the skid control ECU (brake actuator assembly). The pulse signal is created by switching the transistor in the skid control ECU (brake actuator assembly) ON and OFF, which pulls the wire voltage down to 0 V. An equivalent system is used to send this signal from the instrument cluster assembly through terminal +S. A 12 V or 5 V voltage is applied to terminal +S of each ECU or relay connected to this terminal. The transistor in the instrument cluster assembly is controlled by the signal from the skid control ECU (brake actuator assembly). When this transistor is turned on, it pulls the voltage from the various ECUs (through their respective internal resistors) down to 0 V. Each ECU connected to terminal +S of the instrument cluster assembly controls its respective system based on this pulse signal.

  • *a: This vehicle speed signal is created by the skid control ECU (brake actuator assembly). There is no component that can be considered a vehicle speed sensor. In addition, for some systems, vehicle speed information may be received via the CAN communication system.

HINT:

This circuit is used for systems connected to terminal +S. This signal is not used for the operation of the instrument cluster assembly. Components of the instrument cluster assembly, such as the speedometer, operate using data received via CAN communication.

WIRING DIAGRAM

without navigation system

with navigation system

PRECAUTION / NOTICE / HINT

NOTICE:

  • Before replacing the ECM, refer to the Registration section.
    • with Smart Key System:

      Click here

    • without Smart Key System:

      Click here

  • Before replacing the certification ECU (smart key ECU assembly), refer to the Registration section.*1

    Click here

  • When replacing the instrument cluster assembly, always use a new part. If an instrument cluster assembly that was installed in another vehicle is used, the stored information will not match the information transmitted by the vehicle, and a DTC may be stored.
    • *1: with Smart Key System

PROCEDURE

  1. INSPECT ECU TERMINAL VOLTAGE (INPUT VOLTAGE)

(a) Disconnect the connector from the instrument cluster assembly.

*a

Front view of wire harness side connector

(to instrument cluster assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If any of the ECUs specified in the wiring diagram supplies a signal to the instrument cluster assembly, the instrument cluster assembly will output a waveform.

NG

GO TO STEP 5

OK
  1. INSPECT INSTRUMENT CLUSTER ASSEMBLY (OUTPUT VOLTAGE)

(a) Reconnect connector F4 to the instrument cluster assembly.

(b) Disconnect the Skid Control ECU (Brake Actuator Assembly) connector.

*a

Front view of wire harness side connector

(to brake actuator assembly (skid control ECU))

(c) Measure the voltage according to the value(s) shown in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

A42-34 (SP1) - Body ground

Ignition Switch in ON position

11 à 14 V

NG

GO TO STEP 4

OK
  1. INSPECT SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY) (INPUT WAVEFORM)

(a) Check the input waveform.

(1) Disconnect connector A42 from the skid control ECU (brake actuator assembly).

(2) Remove the instrument cluster assembly while leaving the connector(s) connected.

(3) Connect an oscilloscope to terminal F4-5 (SI) and body ground.

(4) Turn the ignition switch ON.

(5) Slowly turn one wheel.

(6) Check the signal waveform according to the condition(s) shown in the table below.

Item

Condition

Oscilloscope Setting

5 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

Ignition switch ON, steering wheel turned

OK:

The waveform is the same as that shown in the diagram.

HINT:

When the system is operating normally, one wheel revolution generates 4 pulses. As vehicle speed increases, the width indicated by (A) in the diagram decreases.

*a

Component with Wire Harness Connected

(instrument cluster assembly)

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)

  1. INSPECT WIRE HARNESS AND CONNECTOR (INSTRUMENT CLUSTER ASSEMBLY - SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY))

(a) Disconnect the connector from the combination meter assembly F4.

(b) Disconnect the A42 connector from the Skid Control ECU (Brake Actuator Assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F4-5 (SI) - A42-34 (SP1)

Always

Below 1 Ω

F4-5 (SI) - Body ground

Always

10 kΩ minimum

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. INSPECT WIRE HARNESS AND CONNECTOR (INSTRUMENT CLUSTER ASSEMBLY - EACH ECU)

(a) Disconnect ECM connector A38.

(b) Disconnect connector F1 from the certification ECU (smart key ECU assembly).*1

(c) Disconnect connector F56 from the front wiper relay assembly.*2

(d) Disconnect connector F47 from the radio receiver assembly.*3

(e) Disconnect connector F129 from the audio and display system assembly.*4

(f) Disconnect connector F135 from the navigation ECU assembly.*5

(g) Measure the resistance according to the value(s) specified in the table below.

  • *1: with Smart Key System
  • *2: With rain sensor
  • *3: for type with radio receiver
  • *4: for type with radio and display
  • *5: with navigation system

Standard resistance:

Tester Connection

Condition

Specified Condition

F4-6 (+S) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CONFIRM MODEL

(a) Select the model to be checked.

Result:

Result

Proceed to

with navigation system

A

without navigation system

B

B

GO TO STEP 11

A
  1. INSPECT NAVIGATION ECU (SHORT IN NAVIGATION ECU)

(a) Disconnect connector F135 from the navigation ECU assembly.

(b) Reconnect the A38 ECM connector.

(c) Reconnect the F1 connector to the certification ECU (smart key ECU assembly).

(d) Reconnect connector F56 to the front wiper relay assembly.

(e) Reconnect connector F129 to the radio receiver and display assembly.

(f) Measure the voltage according to the value(s) specified in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result meets the specification, there may be a short circuit in the navigation ECU.

(g) Reconnect connector F135 to the navigation ECU assembly.

OK

REPLACE NAVIGATION ECU ASSEMBLY

NG
  1. INSPECT AUDIO AND DISPLAY SYSTEM ASSEMBLY (SHORT IN AUDIO AND DISPLAY SYSTEM ASSEMBLY)

(a) Disconnect connector F129 from the radio receiver and display assembly.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the radio receiver and display assembly.

(c) Reconnect connector F129 of the radio receiver and display assembly.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG
  1. CHECK CERTIFICATION ECU (INTELLIGENT KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (INTELLIGENT KEY ECU ASSEMBLY))

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the certification ECU (intelligent key ECU assembly).

(c) Reconnect the F1 connector to the certification ECU (smart key ECU assembly).

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG
  1. CHECK FRONT WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN FRONT WIPER RELAY ASSEMBLY)

(a) Disconnect connector F56 from the front wiper relay assembly.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the front wiper relay assembly.

(c) Reconnect connector F56 to the front wiper relay assembly.

OK

REPLACE FRONT WIPER RELAY ASSEMBLY

NG

REPLACE ECM

  1. CONFIRM MODEL

(a) Select the model to be checked.

Result:

Result

Proceed to

with Smart Key System

A

without Smart Key System

B

B

GO TO STEP 13

A
  1. CHECK CERTIFICATION ECU (INTELLIGENT KEY ECU ASSEMBLY) (SHORT CIRCUIT IN CERTIFICATION ECU (INTELLIGENT KEY ECU ASSEMBLY))

(a) Disconnect the F1 connector from the certification ECU (smart key ECU assembly).

(b) Reconnect the A38 ECM connector.

(c) Reconnect connector F56 of the front wiper relay assembly.*1

(d) Reconnect connector F47 of the radio receiver assembly.*2

(e) Reconnect connector F129 of the audio and display system assembly.*3

(f) Measure the voltage according to the value(s) specified in the table below.

  • *1: With rain sensor
  • *2: for radio receiver type
  • *3: for radio and display type

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the certification ECU (intelligent key ECU assembly).

(g) Reconnect connector F1 of the certification ECU (intelligent key ECU assembly).

OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSY)

NG
  1. CONFIRM MODEL

(a) Select the model to be checked.

Result:

Result

Proceed to

With rain sensor

A

without rain sensor

B

B

GO TO STEP 15

A
  1. CHECK FRONT WIPER RELAY ASSEMBLY (SHORT CIRCUIT IN FRONT WIPER RELAY ASSEMBLY)

(a) Disconnect connector F56 from the front wiper relay assembly.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the front wiper relay assembly.

(c) Reconnect connector F56 to the front wiper relay assembly.

OK

REPLACE FRONT WIPER RELAY ASSEMBLY

NG
  1. CONFIRM MODEL

(a) Select the model to be checked.

Result:

Result

Proceed to

with audio and video system (for radio receiver type)

A

with audio and video system (for radio and display type)

B

without audio and video system

C

B

GO TO STEP 17

C

REPLACE ECM

A
  1. CHECK RADIO RECEIVER ASSEMBLY (SHORT CIRCUIT IN RADIO RECEIVER ASSEMBLY)

(a) Disconnect the F47 radio receiver assembly connector.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the radio receiver assembly.

(c) Reconnect connector F47 of the radio receiver assembly.

OK

REPLACE RADIO RECEIVER ASSEMBLY

NG

REPLACE ECM

  1. INSPECT AUDIO AND DISPLAY SYSTEM ASSEMBLY (SHORT IN AUDIO AND DISPLAY SYSTEM ASSEMBLY)

(a) Disconnect connector F129 from the radio receiver and display assembly.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F4-6 (+S) - Body ground

Ignition Switch in ON position

4,5 à 14 V

HINT:

If the result is within specifications, there may be a short circuit in the radio receiver and display assembly.

(c) Reconnect connector F129 of the radio receiver and display assembly.

OK

REPLACE RADIO AND DISPLAY RECEIVER ASSEMBLY

NG

REPLACE ECM