Adjustment
ADJUSTMENT
PRECAUTION / NOTICE / HINT
PROCEDURE
1. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT
(a) Prepare the vehicle:
- Make sure the vehicle body is not damaged or deformed around the headlights.
- Fill the fuel tank.
- Make sure that the oil is at the specified level.
- Make sure that the engine coolant is at the specified level.
- Inflate the tires to the specified pressure.
- Unload the luggage compartment and the vehicle, and check that the spare tire, tools and jack are in their original positions.
- Bounce the vehicle at each corner to stabilize the suspension.
- Seat an average-weight person (75 kg, 165 lb.) in the driver's seat. (for US and Canada)
- Seat an average-weight person (75 kg, 165 lb.) in the driver's seat. (except US and Canada)
2. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT (using headlight aim tester)
(a) Adjust the headlight aim according to the headlight aim tester instructions.
3. PREPARE VEHICLE FOR HEADLIGHT AIM ADJUSTMENT (using screen)
HINT:
- for US and Canada: perform steps (a), (b), (c), (d) and (e).
- except US and Canada: perform (f), (g), (h), (i) and (j).
(a) Prepare the vehicle:
*a |
Center mark |
- Park the vehicle in a location dark enough to clearly see the cutoff line. The cutoff line is a distinct line below which the headlight light is perceived and above which it is not.
- Position the vehicle at a 90° angle to the wall.
- Keep a distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall.
- Make sure that the vehicle is parked on a level surface.
- Align the front wheels with the vehicle's centerline.
- Shake the vehicle to stabilize the suspension.
NOTICE:
A distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall is required to correctly adjust the headlight aim. If this distance cannot be obtained, use a distance of exactly 3 m (9.84 ft) for checking and adjusting the headlight aim. (the target area size will change depending on the distance, so follow the illustration).
(b) Prepare a thick sheet of white paper (approximately 2 m (6.56 ft) (height) x 4 m (13.1 ft) (width)) to use as a screen.
(c) Draw a vertical line from top to bottom at the center of the screen (V line).
(d) Position the screen as shown in the illustration:
HINT:
- Position the screen perpendicular to the floor.
- Align the V line of the screen with the center of the vehicle.
(e) Draw the reference lines (H line, left V line and right V line) on the screen as shown in the illustration.
*a |
Left V line |
*b |
V line |
*c |
Right V line |
*d |
H line |
*e |
Ground |
HINT:
Mark the headlight bulb center points on the screen.
*a |
Center mark |
(1) H line (headlight height):
Draw a horizontal line across the screen passing through the center marks. The H line should be at the same height as the headlight center marks.
(2) Left V line, right V line (left and right headlight center mark positions):
Draw 2 vertical lines crossing the H line at each of the center marks (aligned with the headlight center marks).
(f) Prepare the vehicle
- Park the vehicle in a location dark enough to clearly see the cutoff line. The cutoff line is a distinct line below which the headlight light is perceived and above which it is not.
- Position the vehicle at a 90° angle to the wall.
- Keep a distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall.
- Make sure that the vehicle is parked on a level surface.
- Align the front wheels with the vehicle's centerline.
- Shake the vehicle to stabilize the suspension.
NOTICE:
A distance of 7.62 m (25 ft) between the vehicle (headlight center marks) and the wall is required to correctly adjust the headlight aim. If this distance cannot be obtained, use a distance of exactly 3 m (9.84 ft) for checking and adjusting the headlight aim. (the target area size will change depending on the distance, so follow the illustration).
*a |
Center mark |
(g) Prepare a thick sheet of white paper (approximately 2 m (6.56 ft) high x 4 m (13.1 ft) wide) to be used as a screen.
(h) Draw a vertical line from top to bottom at the center of the screen (V line).
(i) Position the screen as shown in the illustration.
HINT:
- Position the screen perpendicular to the floor.
- Align the V line of the screen with the center of the vehicle.
(j) Draw the reference lines (H line, left V line and right V line) on the screen as shown in the illustration.
*a |
Left V line |
*b |
V line |
*c |
Right V line |
*d |
H line |
*e |
Ground |
HINT:
Mark the headlight bulb center points on the screen.
*a |
Center mark |
(1) H line (headlight height):
Draw a horizontal line across the screen passing through the center marks. The H line should be at the same height as the headlight center marks.
(2) Left V line, right V line (headlight (right and left) center mark position):
Draw 2 vertical lines crossing the H line at each of the center marks (aligned with the headlight center marks).
4. CHECK HEADLIGHT AIM
(a) Cover the headlight on the opposite side to prevent light from the headlight not being inspected from affecting the headlight aim check.
NOTICE:
Do not leave the headlight covered for more than 3 minutes. The headlight lens is made of synthetic resin and can easily melt or be damaged by heat.
HINT:
When checking the aim of the high beams, cover the low beams.
(b) Start the engine.
(c) Turn on the headlights and check the aim of each beam. (for USA and Canada)
HINT:
- Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
- If the aiming distance is 7.62 m (25 ft):
The low beam cutoff line must be between 101 mm (3.97 in) above or below the H line, and 101 mm (3.97 in) to the left or right of the left or right V line (SAE J599).
- If the aiming distance is 3 m (9.84 ft):
The low beam cutoff line must be between 39 mm (1.56 in) above or below the H line, and 39 mm (1.56 in) to the left or right of the left or right V line (SAE J599).
- If the aiming distance is 7.62 m (25 ft):
The high beam center of intensity must be no more than 101 mm (3.97 in) above or below the H line, and no more than 101 mm (3.97 in) to the left and right of the left or right V line (SAE J599).
- If the aiming distance is 3 m (9.84 ft):
The high beam center of intensity must be no more than 39 mm (1.56 in) above or below the H line, and no more than 39 mm (1.56 in) to the left or right of the left or right V line (SAE J599).
(d) Turn on the headlights and check whether the cutoff line of each low beam matches the specified cutoff line, as shown in the illustration. (except USA and Canada)
HINT:
- Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
- If the aiming distance is 25 m (82 ft):
The low beam cutoff line must be between 48 mm (1.89 in) and 698 mm (2.29 ft) below the H line, and no more than 248 mm (9.79 in) to the left or right of the left or right V line.
- If the aiming distance is 3 m (9.84 ft):
The low beam cutoff line must be between 6 mm (0.227 in) and 83 mm (3.29 in) below the H line, and no more than 29 mm (1.17 in) to the left or right of the left or right V line.
- If the aiming distance is 25 m (82 ft):
The specified low beam target horizontal cutoff line must be 249 mm (9.79 in) below the H line, and point A of the specified low beam target cutoff line must be on the left or right V line.
- If the aiming distance is 3 m (9.84 ft):
The specified low beam target horizontal cutoff line must be 30 mm (1.18 in) below the H line, and point A of the specified low beam target cutoff line must be on the left or right V line.
(e) Turn on the high beams and check whether the center of intensity of each high beam matches the specified center of intensity shown in the illustration. (except USA and Canada)
HINT:
- Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
- If the aiming distance is 25 m (82 ft):
The high beam center of intensity must be no more than 174 mm (6.87 in) above and 248 mm (9.79 in) below the H line, and no more than 497 mm (1.63 ft) to the left or right of the left or right V line.
- If the aiming distance is 3 m (9.84 ft):
The high beam center of intensity must be no more than 20 mm (0.824 in) above and 29 mm (1.17 in) below the H line, and no more than 59 mm (2.35 in) to the left or right of the left or right V line.
5. ADJUST HEADLIGHT AIM
(a) Adjust the headlight aim vertically:
(1) Using a screwdriver, adjust the aim of each headlight within the specified range by turning the adjusting screw (A).
*A |
for US and Canada |
*B |
except USA and Canada |
*a |
Adjusting screw (A) |
- |
- |
NOTICE:
The final turn of the adjusting screw must be made clockwise. If the screw is overtightened, loosen it and then retighten it so that the final turn of the screw is clockwise.
HINT:
- Since the low beams and high beams form one unit, if the low beam aim is correct, the high beam aim is also correct. However, check both sides to be certain.
- When adjusting the vertical aim of the headlight, the horizontal aim also changes. First adjust the vertical position, then correct the horizontal position.
- If the headlight aim cannot be adjusted correctly, check the installation of the headlight unit and the headlight unit lens.
- Check the direction of rotation of the adjusting screw by observing it while tightening. Depending on the screwdriver position, the direction of rotation of the adjusting screw may differ from the direction of rotation of the screwdriver used to tighten it.
(b) Adjust the headlight aim horizontally (except USA and Canada):
(1) Using a screwdriver, adjust the aim of each headlight within the specified range by turning the adjusting screw (B). NOTICE: The final turn of the adjusting screw must be made clockwise. If the screw is overtightened, loosen it and then retighten it so that the final turn of the screw is clockwise. HINT:
|
|
