Windows

ECU Terminals

~36min read

ECU TERMINALS

INSPECT MULTIPLEX NETWORK MAIN SWITCH ASSY

(a) Disconnect the J6 connector from the multiplex network main switch assy.

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

J6-11 (B) - J6-12 (GND)

B - W-B

Power supply

Always

11 à 14 V

J6-12 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the J6 connector to the multiplex network main switch assy.

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

J6-15 (DOWN) - J6-12 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, driver door power window switch not pressed or pulled

11 à 14 V

J6-15 (DOWN) - J6-12 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, driver door power window switch operated, driver door power window switch pressed halfway down (manual operation)

Below 1 V

J6-20 (UP) - J6-12 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, driver door power window switch not pressed or pulled

11 à 14 V

J6-20 (UP) - J6-12 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, driver door power window switch operated, driver door power window switch pulled halfway up (manual operation)

Below 1 V

INSPECT POWER WINDOW SWITCH ASSY

(a) Disconnect the I10 connector from the power window switch assy.

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

I10-7 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the I10 connector to the power window switch assy.

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

I10-2 (LED) - I10-7 (GND)

R - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

I10-2 (LED) - I10-7 (GND)

R - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

I10-5 (UP) - I10-7 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, power window switch assembly not pressed or pulled

11 à 14 V

I10-5 (UP) - I10-7 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I10-5 (UP) - I10-7 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I10-5 (UP) - I10-7 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I10-5 (UP) - I10-7 (GND)

V - W-B

UP output from power window motor

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I10-4 (DOWN) - I10-7 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, power window switch assembly not pressed or pulled

11 à 14 V

I10-4 (DOWN) - I10-7 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I10-4 (DOWN) - I10-7 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I10-4 (DOWN) - I10-7 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I10-4 (DOWN) - I10-7 (GND)

Y - W-B

DOWN output from power window motor

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO UP output

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO UP output

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO UP output

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO DOWN output

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO DOWN output

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I10-8 (AUTO) - I10-7 (GND)

B - W-B

Power window motor AUTO DOWN output

Ignition switch ON, front passenger door power window fully open

11 à 14 V

CHECK REAR POWER WINDOW SWITCH ASSEMBLY (FOR LEFT DOOR)

(a) Disconnect the L3 connector from the rear power window switch assembly (for left door).

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

L3-7 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the L3 connector to the rear power window switch assembly (for left side).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

L3-2 (LED) - L3-7 (GND)

Y - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

L3-2 (LED) - L3-7 (GND)

Y - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

L3-5 (UP) - L3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear power window switch assembly (for left door) neither pressed nor pulled

11 à 14 V

L3-5 (UP) - L3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled halfway up (manual operation)

Below 1 V

L3-5 (UP) - L3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear left door power window fully open

11 à 14 V

L3-5 (UP) - L3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled fully up (manual operation)

Below 1 V

L3-5 (UP) - L3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L3-4 (DOWN) - L3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear power window switch assembly (for left door) neither pressed nor pulled

11 à 14 V

L3-4 (DOWN) - L3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed halfway down (manual operation)

Below 1 V

L3-4 (DOWN) - L3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L3-4 (DOWN) - L3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed fully down (manual operation)

Below 1 V

L3-4 (DOWN) - L3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear left door power window fully open

11 à 14 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear left door power window fully open

11 à 14 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled fully up (manual operation)

Below 1 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed fully down (manual operation)

Below 1 V

L3-8 (AUTO) - L3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear left door power window fully open

11 à 14 V

CHECK REAR POWER WINDOW SWITCH ASSEMBLY (FOR RIGHT DOOR)

(a) Disconnect the K3 connector from the rear power window switch assembly (for right door).

(b) Measure the resistance according to the value(s) in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

K3-7 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

(c) Reconnect the K3 connector to the rear power window switch assembly (for right door).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

K3-2 (LED) - K3-7 (GND)

Y - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

K3-2 (LED) - K3-7 (GND)

Y - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

K3-5 (UP) - K3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear power window switch assembly (for right door) neither pressed nor pulled

11 à 14 V

K3-5 (UP) - K3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled halfway up (manual operation)

Below 1 V

K3-5 (UP) - K3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear right door power window fully open

11 à 14 V

K3-5 (UP) - K3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled fully up (manual operation)

Below 1 V

K3-5 (UP) - K3-7 (GND)

W - W-B

UP output from power window motor

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K3-4 (DOWN) - K3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear power window switch assembly (for right door) neither pressed nor pulled

11 à 14 V

K3-4 (DOWN) - K3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed halfway down (manual operation)

Below 1 V

K3-4 (DOWN) - K3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K3-4 (DOWN) - K3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed fully down (manual operation)

Below 1 V

K3-4 (DOWN) - K3-7 (GND)

GR - W-B

DOWN output from power window motor

Ignition switch ON, rear right door power window fully open

11 à 14 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear right door power window fully open

11 à 14 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled fully up (manual operation)

Below 1 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO UP output

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed fully down (manual operation)

Below 1 V

K3-8 (AUTO) - K3-7 (GND)

V - W-B

Power window motor AUTO DOWN output

Ignition switch ON, rear right door power window fully open

11 à 14 V

CHECK POWER WINDOW MOTOR ASSEMBLY (FOR DRIVER DOOR)

(a) Disconnect the J2 connector from the power window motor assembly (for driver door).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

J2-1 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

J2-2 (B) - Body ground

L - Body ground

Power supply

Always

11 à 14 V

(c) Reconnect the J2 connector to the power window motor assembly (for driver door).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

J2-7 (DOWN) - J2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, multiplex network main switch assembly (driver door power window switch) not pressed or pulled

11 à 14 V

J2-7 (DOWN) - J2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, driver door power window operated, multiplex network main switch assembly (driver door power window switch) pressed halfway down (manual operation)

Below 1 V

J2-7 (DOWN) - J2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, driver door power window fully closed

11 à 14 V

J2-7 (DOWN) - J2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, driver door power window operated, multiplex network main switch assembly (driver door power window switch) pressed fully down (automatic operation)

Below 1 V

J2-7 (DOWN) - J2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, driver door power window fully open

11 à 14 V

J2-10 (UP) - J2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, multiplex network main switch assembly (driver door power window switch) not pressed or pulled

11 à 14 V

J2-10 (UP) - J2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, driver door power window operated, multiplex network main switch assembly (driver door power window switch) pulled halfway up (manual operation)

Below 1 V

J2-10 (UP) - J2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch in ON position, multiplex network main switch assembly (driver door power window switch) fully open

11 à 14 V

J2-10 (UP) - J2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch in ON position, driver door power window operated, multiplex network main switch assembly (driver door power window switch) pulled fully up (automatic operation)

Below 1 V

J2-10 (UP) - J2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, driver door power window fully closed

11 à 14 V

INSPECT POWER WINDOW MOTOR ASSEMBLY (FOR FRONT PASSENGER DOOR)

(a) Disconnect the I2 connector from the power window motor assembly (for front passenger door).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

I2-1 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

I2-2 (B) - Body ground

L - Body ground

Power supply

Always

11 à 14 V

(c) Reconnect the I2 connector to the power window motor assembly (for front passenger door).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO UP

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO UP

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO UP

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO DOWN

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO DOWN

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I2-4 (AUTO) - I2-1 (GND)

B - W-B

Power window motor input AUTO DOWN

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I2-5 (LED) - I2-1 (GND)

R - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

I2-5 (LED) - I2-1 (GND)

R - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

I2-7 (DOWN) - I2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, power window switch assembly not pressed or pulled

11 à 14 V

I2-7 (DOWN) - I2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I2-7 (DOWN) - I2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

I2-7 (DOWN) - I2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, front passenger door power window operated, power window switch assembly pressed halfway down (manual operation)

Below 1 V

I2-7 (DOWN) - I2-1 (GND)

Y - W-B

Power window motor DOWN input

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I2-10 (UP) - I2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, power window switch assembly not pressed or pulled

11 à 14 V

I2-10 (UP) - I2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I2-10 (UP) - I2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, front passenger door power window fully open

11 à 14 V

I2-10 (UP) - I2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, front passenger door power window operated, power window switch assembly pulled halfway up (manual operation)

Below 1 V

I2-10 (UP) - I2-1 (GND)

V - W-B

Power window motor UP input

Ignition switch ON, front passenger door power window fully closed

11 à 14 V

INSPECT POWER WINDOW MOTOR ASSEMBLY (FOR REAR LEFT DOOR)

(a) Disconnect the L2 connector from the power window motor assembly (for rear left door).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

L2-1 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

L2-2 (B) - Body ground

R - Body ground

Power supply

Always

11 à 14 V

(c) Reconnect the L2 connector to the power window motor assembly (for rear left door).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear left door power window fully open

11 à 14 V

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled fully up (manual operation)

Below 1 V

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed fully down (manual operation)

Below 1 V

L2-4 (AUTO) - L2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear left door power window fully open

11 à 14 V

L2-5 (LED) - L2-1 (GND)

Y - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

L2-5 (LED) - L2-1 (GND)

Y - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

L2-7 (DOWN) - L2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear power window switch assembly (for left door) neither pressed nor pulled

11 à 14 V

L2-7 (DOWN) - L2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed halfway down (manual operation)

Below 1 V

L2-7 (DOWN) - L2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear left door power window fully closed

11 à 14 V

L2-7 (DOWN) - L2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pressed fully down (manual operation)

Below 1 V

L2-7 (DOWN) - L2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear left door power window fully open

11 à 14 V

L2-10 (UP) - L2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear power window switch assembly (for left door) neither pressed nor pulled

11 à 14 V

L2-10 (UP) - L2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled halfway up (manual operation)

Below 1 V

L2-10 (UP) - L2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear left door power window fully open

11 à 14 V

L2-10 (UP) - L2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear left door power window operated, rear power window switch assembly (for left door) pulled fully up (manual operation)

Below 1 V

L2-10 (UP) - L2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear left door power window fully closed

11 à 14 V

INSPECT POWER WINDOW MOTOR ASSEMBLY (FOR REAR RIGHT DOOR)

(a) Disconnect the K2 connector from the power window motor assembly (for rear right door).

(b) Measure the voltage and resistance according to the value(s) specified in the table below.

HINT:

Measure the values at the wire harness side with the connector disconnected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

K2-1 (GND) - Body ground

W-B - Body ground

Ground

Always

Below 1 Ω

K2-2 (B) - Body ground

R - Body ground

Power supply

Always

11 à 14 V

(c) Reconnect the K2 connector to the power window motor assembly (for rear right door).

(d) Measure the voltage according to the value(s) specified in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear right door power window fully open

11 à 14 V

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled fully up (manual operation)

Below 1 V

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO UP

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed fully down (manual operation)

Below 1 V

K2-4 (AUTO) - K2-1 (GND)

V - W-B

Power window motor input AUTO DOWN

Ignition switch ON, rear right door power window fully open

11 à 14 V

K2-5 (LED) - K2-1 (GND)

Y - W-B

LED illumination signal

The headlight switch is in the TAIL position

11 à 14 V

K2-5 (LED) - K2-1 (GND)

Y - W-B

LED illumination signal

The headlight/dimmer switch is not in the TAIL position

Below 1 V

K2-7 (DOWN) - K2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear power window switch assembly (for right door) neither pressed nor pulled

11 à 14 V

K2-7 (DOWN) - K2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed halfway down (manual operation)

Below 1 V

K2-7 (DOWN) - K2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear right door power window fully closed

11 à 14 V

K2-7 (DOWN) - K2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pressed fully down (manual operation)

Below 1 V

K2-7 (DOWN) - K2-1 (GND)

GR - W-B

Power window motor DOWN input

Ignition switch ON, rear right door power window fully open

11 à 14 V

K2-10 (UP) - K2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear power window switch assembly (for right door) neither pressed nor pulled

11 à 14 V

K2-10 (UP) - K2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled halfway up (manual operation)

Below 1 V

K2-10 (UP) - K2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear right door power window fully open

11 à 14 V

K2-10 (UP) - K2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear right door power window operated, rear power window switch assembly (for right door) pulled fully up (manual operation)

Below 1 V

K2-10 (UP) - K2-1 (GND)

W - W-B

Power window motor UP input

Ignition switch ON, rear right door power window fully closed

11 à 14 V

CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

*A

Main Body ECU (Multiplex Network Body ECU) with 2 connectors

-

-

*1

Main body ECU (multiplex network body ECU)

-

-

*a

2 connectors

-

-

*A

Main Body ECU (Multiplex Network Body ECU) with 1 connector

-

-

*1

Main body ECU (multiplex network body ECU)

-

-

*a

1 connector

-

-

(a) Remove the main body ECU (multiplex network body ECU) from the instrument panel junction block assy.

Click here

(b) Reconnect the connectors to the instrument panel junction block assy.

(c) Measure the voltage and resistance according to the value(s) in the table below.

HINT:

Measure the values at the wire harness side with the connectors connected.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

MB-11 (GND1) - Body ground

-

Ground

Always

Below 1 Ω

MB-31 (BECU) - Body ground

-

Battery power supply

Always

11 à 14 V

MB-30 (ACC) - Body ground

-

ACC power supply

Ignition Switch in ACC position

11 à 14 V

MB-30 (ACC) - Body ground

-

ACC power supply

Ignition Switch in OFF position

Below 1 V

MB-32 (IG) - Body ground

-

IG power supply

Ignition Switch in ON position

11 à 14 V

MB-32 (IG) - Body ground

-

IG power supply

Ignition Switch in OFF position

Below 1 V

(d) Reinstall the main body ECU (multiplex network body ECU) onto the instrument panel junction block assy.

Click here

(e) Measure the voltage and check the pulses according to the value(s) in the table below.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

F15-6 (FLCY) - Body ground

R - Body ground

Front door (left) courtesy light switch input voltage

Front left door open

Below 1 V

F15-6 (FLCY) - Body ground

R - Body ground

Front door (left) courtesy light switch input voltage

Front left door closed

11 à 14 V

F15-27 (FRCY) - Body ground

BR - Body ground

Front door (right) courtesy light switch input voltage

Front right door open

Below 1 V

F15-27 (FRCY) - Body ground

BR - Body ground

Front door (right) courtesy light switch input voltage

Front right door closed

11 à 14 V

F15-29 (L2) - Body ground

G - Body ground

Key-linked driver side door lock input

Driver side door key cylinder set to lock position

Below 1 V

F15-29 (L2) - Body ground

G - Body ground

Key-linked driver side door lock input

Driver door lock cylinder not turned

Pulse generation

F15-2 (UL3) - Body ground

L - Body ground

Key-linked driver side door unlock input

Driver side door key cylinder set to unlock position

Below 1 V

F15-2 (UL3) - Body ground

L - Body ground

Key-linked driver side door unlock input

Driver door lock cylinder not turned

Pulse generation