Windows

How to Use Troubleshooting

~4min read

PRECAUTION / NOTICE / HINT

HINT:

  • Follow the procedure below to troubleshoot the power window control system.
  • *: Use the Techstream.

PROCEDURE

  1. VEHICLE BROUGHT TO WORKSHOP

NEXT
  1. CUSTOMER PROBLEM ANALYSIS

HINT:

  • When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
  • Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
  • The following 5 elements are essential for analyzing the problem:

    What

    Vehicle model, system name

    When

    Date, time, frequency of occurrence

    Where

    Road conditions

    What were the conditions?

    Driving conditions, weather conditions

    How did it happen?

    Problem Symptoms

NEXT
  1. PRELIMINARY CHECKS

(a) Measure the battery voltage with the ignition switch OFF.

Standard voltage:

11 à 14 V

If the voltage is below 11 V, charge or replace the battery before proceeding to the next step.

(b) Check the fuses and relays.

(c) Check the connectors and terminals for any abnormality, such as loose connections, deformation, etc.

NEXT
  1. CHECK CAN COMMUNICATION SYSTEM FUNCTION*

(a) Using the Techstream, check for DTCs related to the CAN communication system.

Click here

Result:

Result

Proceed to

No CAN system DTCs are output

A

CAN-related DTCs are output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. CHECK LIN COMMUNICATION SYSTEM COMMUNICATION FUNCTION*

(a) Using the Techstream, check for DTCs related to the LIN communication system.

Click here

Result:

Result

Proceed to

LIN system DTCs are not output

A

LIN-related DTCs are output

B

B

GO TO LIN COMMUNICATION SYSTEM

A
  1. CHECK DTCs*

(a) Check the DTCs and record all codes output.

Click here

Body Electrical > Master Switch > Trouble Codes Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble Codes

(b) Clear the DTCs.

Body Electrical > Master Switch > Clear DTCs Body Electrical > D-Door Motor > Clear DTCs Body Electrical > P-Door Motor > Clear DTCs Body Electrical > RL-Door Motor > Clear DTCs Body Electrical > RR-Door Motor > Clear DTCs

(c) Check the DTCs again.

Body Electrical > Master Switch > Trouble Codes Body Electrical > D-Door Motor > Trouble Codes Body Electrical > P-Door Motor > Trouble Codes Body Electrical > RL-Door Motor > Trouble Codes Body Electrical > RR-Door Motor > Trouble Codes

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

B

GO TO DIAGNOSTIC TROUBLE CODE CHART

A
  1. SYMPTOM TROUBLESHOOTING TABLE

(a) Refer to the Symptom Troubleshooting Table.

Click here

Result:

Result

Proceed to

The malfunction is not listed in the Problem Symptoms Table

A

The malfunction is listed in the Problem Symptoms Table

B

B

GO TO STEP 9

A
  1. GENERAL ANALYSIS AND TROUBLESHOOTING*

(a) Operation Check

Click here

(b) ECU Terminals

Click here

(c) Data List/Active Test

Click here

(d) Diagnostic Mode Table

Click here

(e) Check

NEXT
  1. ADJUST, REPAIR OR REPLACE

(a) Check whether any of the door glass regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass run channels have been removed and installed.

Result:

Result

Proceed to

One of the door glass regulator sub-assemblies, power window regulator motor assemblies, door glass or door glass run channels has been removed and installed.

A

The door glass regulator sub-assemblies, power window regulator motor assemblies, door glass and door glass run channels have not been removed and installed.

B

B

GO TO STEP 11

A
  1. INITIALIZE POWER WINDOW CONTROL SYSTEM

(a) If any of the door power windows, power window regulator motor assemblies, door glass or door glass run channels have been removed and installed, perform the "Initialize Power Window Control System" procedure for the applicable door glass.

Click here

NEXT
  1. CONFIRMATION TEST

NEXT

END