Windows

Fail-Safe Table

~7min read

FAIL-SAFE TABLE

PULSE FAULT

(a) If a pulse sensor built into the power window motor assembly malfunctions, the following power window operations will be disabled.

Multiplex network main switch assembly, power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Ignition Switch in ON position

Ignition Switch in OFF position

(keyless operation allowed)

Ignition Switch in OFF position

(keyless operation disabled)

Manual close (door switch)

▲

X

X

Manual open (door switch)

●

X

X

Automatic close (door switch)

X

X

X

Automatic open (door switch)

X

X

X

Manual close (remote switch operation)

X

X

X

Manual open (remote switch operation)

X

X

X

Automatic close (remote switch operation)

X

X

X

Automatic open (remote switch operation)

X

X

X

Key-linked open/close

X

X

X

Remote transmitter-linked open/close

X

X

X

HINT:

  • ●: Operates without pinch/trap protection function
  • ▲: Operates for approximately 0.4 seconds without pinch/trap protection function
  • X: Operation disabled
Safety mode cancellation conditions
  • When the pulse sensor is normal, to cancel safety mode, pull the power window switch to the automatic close position and hold it for at least 1 second to fully close the window from the fully open position. This restores the automatic close/open function.

NON-DETECTION ZONE SHIFT TOWARD OPEN DIRECTION

(a) If the window glass position or the learned position is abnormal, the following power window operations will be disabled.

Multiplex network main switch assembly, power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Ignition Switch in ON position

Ignition Switch in OFF position

(keyless operation allowed)

Ignition Switch in OFF position

(keyless operation disabled)

Manual close (door switch)

●

X

X

Manual open (door switch)

●

X

X

Automatic close (door switch)

X

X

X

Automatic open (door switch)

X

X

X

Manual close (remote switch operation)

X

X

X

Manual open (remote switch operation)

X

X

X

Automatic close (remote switch operation)

X

X

X

Automatic open (remote switch operation)

X

X

X

Key-linked open/close

X

X

X

Remote transmitter-linked open/close

X

X

X

HINT:

  • ●: Operates without pinch/trap protection function
  • X: Operation disabled
Safety mode cancellation conditions
  • When the pulse sensor is normal, to cancel safety mode, pull the power window switch to the automatic close position and hold it for at least 1 second to fully close the window from the fully open position. This restores the automatic close/open function.

INITIALIZATION FAULT

(a) During initialization, if the power window position or the complete initialization status cannot be correctly retrieved from non-volatile memory, the following power window operations will be disabled.

Multiplex network main switch assembly, power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Ignition Switch in ON position

Ignition Switch in OFF position

(keyless operation allowed)

Ignition Switch in OFF position

(keyless operation disabled)

Manual close (door switch)

●

X

X

Manual open (door switch)

●

X

X

Automatic close (door switch)

X

X

X

Automatic open (door switch)

X

X

X

Manual close (remote switch operation)

X

X

X

Manual open (remote switch operation)

X

X

X

Automatic close (remote switch operation)

X

X

X

Automatic open (remote switch operation)

X

X

X

Key-linked open/close

X

X

X

Remote transmitter-linked open/close

X

X

X

HINT:

  • ●: Operates without pinch/trap protection function
  • X: Operation disabled
Safety mode cancellation conditions
  • Initialize the power window motor assembly.

    Click here

LIN COMMUNICATION FAULT

(a) If the LIN communication system malfunctions (communication interruption), the following power window control operations will be disabled. (Operation is only possible using the power window switch on each seat.)

Multiplex Network Master Switch Assembly

Power window operation

Condition

Always

Manual close

●*

Manual open

●

Auto close

-

Auto open

-

Power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Always

Manual close

●*

Manual open

●

Auto close

●*

Auto open

●

HINT:

  • ●: Operates without pinch/trap protection function
  • *: The anti-pinch function may operate.
Safety mode cancellation conditions
  • Check the LIN communication system DTC

    Click here

PULSE SENSOR MALFUNCTION AND LIN COMMUNICATION MALFUNCTION

(a) If the LIN communication system malfunctions (communication stops) and the pulse sensor malfunctions, the following power window operations are disabled.

Multiplex network main switch assembly, power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Always

Manual close

X

Manual open

X

Auto close

X

Auto open

X

HINT:

  • X: Operation disabled
  • Door switch:

    If the anti-pinch function does not operate due to a LIN communication line malfunction, the manual and automatic close functions will not be activated, because the ignition signal status is unknown.

  • Remote switch operation:

    This operation is not possible when LIN communication fails.

NON-DETECTION ZONE MOVES TOWARD OPEN DIRECTION AND LIN COMMUNICATION MALFUNCTION / INITIAL MALFUNCTION AND LIN COMMUNICATION MALFUNCTION

(a) If the LIN communication system malfunctions and the window position and learned value are abnormal, or if the LIN communication system malfunctions and the window position or the initialization complete status cannot be correctly read from non-volatile memory during initialization, the following power window operations are disabled.

Multiplex Network Master Switch Assembly

Power window operation

Condition

Always

Manual close

●*

Manual open

●

Auto close

-

Auto open

-

Power window switch assembly, rear power window switch assembly (for right and left doors)

Power window operation

Condition

Always

Manual close

●*

Manual open

●

Auto close

X

Auto open

X

HINT:

  • ●: Operates without pinch/trap protection function
  • X: Operation disabled
  • *: Anti-pinch function operational and window direction reverses once it returns to the fully closed position.
  • Remote switch operation:

    This operation is not possible when LIN communication fails.