Windows

System Description

~6min read

SYSTEM DESCRIPTION

DESCRIPTION OF POWER WINDOW CONTROL SYSTEM

(a) The power window control system controls the operation of the power windows using the power window regulator motor assemblies. The main components of this system are the multiplex network main switch assembly (mounted on the driver's door), the front passenger power window switch assembly (mounted on the front passenger's door), and the rear power window switch assemblies (mounted on the rear doors). Operating a power window switch sends electrical current to the corresponding power window regulator motor.

FUNCTION OF MAIN COMPONENTS

The power window control system consists of the following components:

Component

General Description

Multiplex Network Master Switch Assembly

  • Controls the operation of the power window for all windows.
  • Can be used to operate all power windows when the window lock switch is in the ON (pressed in) position.

Power window switch assembly

  • Located on the front passenger door.
  • Controls the operation of the front passenger power window.

Rear power window switch assembly

  • Left door
  • Right door
  • Located on the rear doors.
  • Controls the operation of the power window for the corresponding window.

Power Window Regulator Motor Assembly

  • Receives signals from the switch and converts them to activate the motor. As a result, the position of the power window changes.
  • Uses the Hall ICs built into the regulator motor and the power window ECUs to detect the position and pinching of the power window.

SYSTEM OPERATION

The power window control system has the following functions:

Function

General Description

Manual up and down function

Function that closes the power window when the power window switch is pulled up halfway, and opens it when pressed down halfway. The power window stops as soon as the switch is released.

Automatic Open and Close Function

Function that allows the power window of each door to be fully opened or closed by pulling or pushing the multiplex network main switch assembly, the power window switch assembly, or the rear power window switch assembly fully once.

Window lock function

  • Function that disables the power window switch assembly and the rear power window switch assembly operation when the window lock switch is in the ON (pressed in) position.
  • The power window switch assembly and the rear power window switch assembly can be operated when the window lock switch is in the OFF (not pressed in) position.

Anti-Pinch Function

Function that automatically stops and lowers the power window if a foreign object becomes caught between the door and the door glass during automatic or manual closing.

Anti-Pinch Function Operation

Function that automatically stops the power window if something becomes caught between the door and the door glass during automatic or manual opening.

Remote Control Function

Function that allows the multiplex network main switch assembly to control the automatic and manual up and down operations of the front passenger door power window and the rear door power windows.

Keyless Operation

  • Function that allows all power windows to be operated for approximately 45 seconds after the ignition switch is turned to OFF, as long as the driver's door or front passenger door has not been opened.
  • When 45 seconds have elapsed, or if the driver's or front passenger door is opened after the ignition switch is turned to OFF, the keyless operation is deactivated.

HINT:

  • If a power window is operated in automatic mode while keyless operation is in the ON position and the driver's or passenger door is open, the power window continues to operate.*4
  • If a power window is operated in automatic mode while keyless operation is in the ON position and the driver's or passenger door is open, the power window stops operating.*5

Function linked to the key*1

  • When the electronic key transmitter sub-assembly is not inside the vehicle*2, or when the door control transmitter assembly is not inserted into the key cylinder*3, the driver's door is locked, and the driver's door key cylinder is turned and held in the lock position for at least 1.5 seconds, the main body ECU (multiplex network body ECU) activates the power window regulator motor assemblies to close all power windows while the key cylinder is turned.
  • Similarly, when the driver's door is unlocked, turning and holding the driver's door key cylinder in the unlock position for at least 1.5 seconds opens all power windows.

Function linked to the remote control transmitter*1

  • When the main body ECU (multiplex network body ECU) receives an UNLOCK signal from the electronic key transmitter sub-assembly*2 or the door control transmitter assembly*3 for at least 3 seconds, the main body ECU (multiplex network body ECU) sends an operation request signal to the power window ECU of each power window regulator motor assembly. As a result, the power window regulator motor assembly opens all power windows.

Power Window Open Warning Function

When the ignition switch is turned from ON to OFF and the driver's door is opened with a power window open, the instrument cluster assembly buzzer sounds once and a warning message is displayed on the multi-information display.

Diagnosis

Function that diagnoses the power window control system if one of the power window ECUs (built into each power window regulator motor assembly) detects a malfunction in the system.

Safety

  • Function that disables some of the power window control system functions if the pulse sensor in the power window regulator motor assembly malfunctions.
  • The auto close and auto open function and the remote control function are disabled.
  • *1: This function is set via a customization setting because it is disabled by default.
  • *2: with Smart Key System
  • *3: without Smart Key System
  • *4: without Pre-Crash Safety System
  • *5: with Pre-Crash Safety System