Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / (desired system) / Data List.
(e) Read the Data List by following the instructions on the Techstream.
Body Electrical > Master Switch > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
D Door P/W Auto SW |
Driver door power window auto switch signal |
OFF or ON |
OFF: Driver door power window auto close or open switch not operated ON: Driver door power window auto close or open switch operated. |
- |
P Door P/W Auto SW |
Front passenger side power window auto switch signal |
OFF or ON |
OFF: Front passenger door power window auto close or open switch not operated ON: Front passenger door power window auto close or open switch operated |
- |
RR Door P/W Auto SW |
Rear right door power window auto switch signal |
OFF or ON |
OFF: Rear right door power window auto close or open switch not operated ON: Rear right door power window auto close or open switch operated |
- |
RL Door P/W Auto SW |
Rear left door power window auto switch signal |
OFF or ON |
OFF: Rear left door power window auto close or open switch not operated ON: Rear left door power window auto close or open switch operated |
- |
P Door P/W Up SW |
Front passenger door power window manual close switch signal |
OFF or ON |
OFF: Front passenger door power window manual close switch not operated ON: Front passenger door power window manual close switch operated |
- |
RR Door P/W up switch |
Rear right door power window manual close switch signal |
OFF or ON |
OFF: Rear right door power window manual close switch not operated ON: Rear right door power window manual close switch operated |
- |
RL Door P/W up switch |
Rear left door power window manual close switch signal |
OFF or ON |
OFF: Rear left door power window manual close switch not operated ON: Rear left door power window manual close switch operated |
- |
P Door P/W Down SW |
Front passenger door power window manual open switch signal |
OFF or ON |
OFF: Front passenger door power window manual open switch not operated ON: Front passenger door power window manual open switch operated |
- |
RR Door P/W Down SW |
Rear right door power window manual open switch signal |
OFF or ON |
OFF: Rear right door power window manual open switch not operated ON: Rear right door power window manual open switch operated |
- |
RL Door P/W Down SW |
Rear left door power window manual open switch signal |
OFF or ON |
OFF: Rear left door power window manual open switch not operated ON: Rear left door power window manual open switch operated |
- |
Window Lock Switch Status |
Window lock switch signal |
OFF or ON |
OFF: Window lock switch in OFF position (not pressed) ON: Window lock switch in ON position (pressed) |
- |
Number of Trouble Codes |
Number of DTCs |
Min.: 0 or Max.: 255 |
The number of stored DTCs is displayed |
- |
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
D Door P/W Auto SW |
Driver door power window auto switch signal |
OFF or ON |
OFF: Driver door power window auto close or open switch not operated ON: Driver door power window auto close or open switch operated. |
- |
D Door P/W Up SW |
Driver door power window manual UP switch signal |
OFF or ON |
OFF: Driver door power window manual close switch not operated ON: Driver's side door power window manual close switch is operated |
- |
D Door P/W Down SW |
Driver's side door power window manual DOWN switch signal |
OFF or ON |
OFF: Driver's side door power window manual open switch is not operated ON: Driver's side door power window manual open switch is operated |
- |
Glass Position (Close-1/4) |
Margin for power window anti-pinch trigger force within the range from fully closed to 1/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (1/4-2/4) |
Margin for power window anti-pinch trigger force within the range from 1/4 to 1/2 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (2/4-3/4) |
Margin for power window anti-pinch trigger force within the range from 1/2 to 3/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (3/4-Open) |
Margin for power window anti-pinch trigger force within the range from 3/4 open to fully open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
D Window Auto Up |
Auto close operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
D Window Auto Down |
Auto open operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
Number of Trouble Codes |
Number of DTCs |
Min.: 0 or Max.: 255 |
The number of stored DTCs is displayed |
- |
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
P Door P/W Auto SW |
Front passenger side power window auto switch signal |
OFF or ON |
OFF: Front passenger door power window auto close or open switch not operated ON: Front passenger door power window auto close or open switch operated |
- |
P Door P/W Up SW |
Front passenger door power window manual close switch signal |
OFF or ON |
OFF: Front passenger door power window manual close switch not operated ON: Front passenger door power window manual close switch operated |
- |
P Door P/W Down SW |
Front passenger door power window manual open switch signal |
OFF or ON |
OFF: Front passenger door power window manual open switch not operated ON: Front passenger door power window manual open switch operated |
- |
Glass Position (Close-1/4) |
Margin for power window anti-pinch trigger force within the range from fully closed to 1/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (1/4-2/4) |
Margin for power window anti-pinch trigger force within the range from 1/4 to 1/2 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (2/4-3/4) |
Margin for power window anti-pinch trigger force within the range from 1/2 to 3/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (3/4-Open) |
Margin for power window anti-pinch trigger force within the range from 3/4 open to fully open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
P Window Auto Up |
Auto close function using the power window switch assembly |
OFF or ON |
Customised setting displayed |
- |
P Window Auto Up From Driver |
Remote auto close operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
P Window Auto Down |
Auto open function using the power window switch assembly |
OFF or ON |
Customised setting displayed |
- |
P Window Auto Down From Driver |
Remote auto open operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
Number of Trouble Codes |
Number of DTCs |
Min.: 0 or Max.: 255 |
The number of stored DTCs is displayed |
- |
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
RL Door P/W Auto SW |
Rear left door power window auto switch signal |
OFF or ON |
OFF: Rear left door power window auto close or open switch not operated ON: Rear left door power window auto close or open switch operated |
- |
RL Door P/W Up SW |
Rear left door power window manual close switch signal |
OFF or ON |
OFF: Rear left door power window manual close switch not operated ON: Rear left door power window manual close switch operated |
- |
RL Door P/W Down SW |
Rear left door power window manual open switch signal |
OFF or ON |
OFF: Rear left door power window manual open switch not operated ON: Rear left door power window manual open switch operated |
- |
Glass Position (Close-1/4) |
Margin for power window anti-pinch trigger force within the range from fully closed to 1/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (1/4-2/4) |
Margin for power window anti-pinch trigger force within the range from 1/4 to 1/2 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (2/4-3/4) |
Margin for power window anti-pinch trigger force within the range from 1/2 to 3/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (3/4-Open) |
Margin for power window anti-pinch trigger force within the range from 3/4 open to fully open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
RL Window Auto Up |
Auto close function using the rear power window switch assembly (for LH door) |
OFF or ON |
Customised setting displayed |
- |
RL Window Auto Up From Driver |
Remote auto close operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
RL Window Auto Down |
Auto open function using the rear power window switch assembly (for LH door) |
OFF or ON |
Customised setting displayed |
- |
RL Window Auto Down From Driver |
Remote auto open operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
Number of Trouble Codes |
Number of DTCs |
Min.: 0 or Max.: 255 |
The number of stored DTCs is displayed |
- |
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
RR Door P/W Auto SW |
Rear right door power window auto switch signal |
OFF or ON |
OFF: Rear right door power window auto close or open switch not operated ON: Rear right door power window auto close or open switch operated |
- |
RR Door P/W Up SW |
Rear right door power window manual close switch signal |
OFF or ON |
OFF: Rear right door power window manual close switch not operated ON: Rear right door power window manual close switch operated |
- |
RR Door P/W Down SW |
Rear right door power window manual open switch signal |
OFF or ON |
OFF: Rear right door power window manual open switch not operated ON: Rear right door power window manual open switch operated |
- |
Glass Position (Close-1/4) |
Margin for power window anti-pinch trigger force within the range from 1/4 to 1/2 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (1/4-2/4) |
Margin for power window anti-pinch trigger force within the range from 1/2 to 3/4 open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (2/4-3/4) |
Margin for power window anti-pinch trigger force within the range from 3/4 open to fully open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
Glass Position (3/4-Open) |
Margin for power window anti-pinch trigger force within the range from 3/4 open to fully open |
OK or Caution |
OK: Normal manual close operation Caution: Pinching detected within the specified range |
The warning is displayed only when the power window ECU built into the power window regulator motor assembly detects pinching. |
RR Window Auto Up |
Auto close function using the rear power window switch assembly (for RH door) |
OFF or ON |
Customised setting displayed |
- |
RR Window Auto Up From Driver |
Remote auto close operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
RR Window Auto Down |
Auto open function using the rear power window switch assembly (for RH door) |
OFF or ON |
Customised setting displayed |
- |
RR Window Auto Down From Driver |
Remote auto open operation using the multiplex network master switch assembly |
OFF or ON |
Customised setting displayed |
- |
Number of Trouble Codes |
Number of DTCs |
Min.: 0 or Max.: 255 |
The number of stored DTCs is displayed |
- |
Tester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
IG SW |
IG Switch Position |
OFF or ON |
OFF: Ignition switch in OFF position ON: Ignition switch in ON position |
"OFF" is also displayed for this item when the ignition switch is in the ACC position. |
Door Key SW-Lock |
Driver's door lock/unlock switch lock signal (key-linked lock switch) |
OFF or ON |
OFF: Driver's door lock cylinder not turned ON: Driver's door lock cylinder set to lock position |
- |
D Door Key SW-UL |
Driver's door lock/unlock switch unlock signal (key-linked unlock switch) |
OFF or ON |
OFF: Driver's door lock cylinder not turned ON: Driver's door lock cylinder set to unlock position |
- |
FR Door Courtesy SW |
Front door (RH) courtesy light switch assembly signal |
OFF or ON |
OFF: Front RH door closed ON: Front RH door open |
- |
FL Door Courtesy SW |
Front door (LH) courtesy light switch assembly signal |
OFF or ON |
OFF: Front left door closed ON: Front left door open |
- |
Door Key P/W Up |
Power window close linked to door key |
OFF or ON |
Customised setting displayed |
- |
Door Key P/W Down |
Power window open linked to door key |
OFF or ON |
Customised setting displayed |
- |
P/W Down W/ Transmit |
Power window open linked to remote control transmitter |
OFF or ON |
Customised setting displayed |
- |
P/W Wireless Ope Buzz |
Power window buzzer automatic response for remote control function |
OFF or ON |
Customised setting displayed |
- |
Window Open Warning |
Power window open warning |
OFF or ON |
Customised setting displayed |
- |
D-Door Motor Communication |
Connection status between the driver's door power window regulator motor assembly and the main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Communication interrupted OK: Communication normal |
- |
P-Door Motor Communication |
Connection status between the front passenger door power window regulator motor assembly and the main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Communication interrupted OK: Communication normal |
- |
RR-Door Motor Communication |
Connection status between the rear RH door power window regulator motor assembly and the main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Communication interrupted OK: Communication normal |
- |
RL-Door Motor Communication |
Connection status between the rear LH door power window regulator motor assembly and the main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Communication interrupted OK: Communication normal |
- |
Master SW Communication |
Connection status between the multiplex network master switch assembly and the main body ECU (multiplex network body ECU) |
STOP or OK |
STOP: Communication interrupted OK: Communication normal |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menu items: Body Electrical / (desired system) / Active Test.
(e) Perform the Active Test by following the Techstream instructions.
CAUTION:
During this test, take care not to injure yourself on moving vehicle parts. During the Active Test, the anti-pinch function does not operate.
Body Electrical > D-Door Motor > Active TestTester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Power Window |
Power Window |
OFF / DOWN / UP |
- |
Tester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Power Window |
Power Window |
OFF / DOWN / UP |
- |
Tester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Power Window |
Power Window |
OFF / DOWN / UP |
- |
Tester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Power Window |
Power Window |
OFF / DOWN / UP |
- |