Exterior Lighting

Data List / Active Test

~5min read

DATA LIST / ACTIVE TEST

DATA LIST

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / HL AutoLeveling / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > HL AutoLeveling > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Front Window Washer Switch

Front washer switch signal

ON or OFF

ON: Front washer switch is ON

OFF: Front washer switch is OFF

-

Headlight Low Beam State

Low beam headlight status

ON or OFF

ON: Low beam headlights on

OFF: Low beam headlights off

-

Headlight High Beam State

High beam headlight status

ON or OFF

ON: High beam headlights on

OFF: High beam headlights off

-

DRL Operating State

DRL Status

ON or OFF

ON: DRL is ON

OFF: DRL is OFF

-

Daylight Operating State

Daytime running light status

ON or OFF

ON: Daytime running lights on

OFF: Daytime running lights off

-

Clearance Light State

Clearance light status

ON or OFF

ON: Clearance lights on

OFF: Clearance lights off

-

+B

Left headlight ECU sub-assembly ignition power supply voltage value

0 à 19,75 V

11,00 à 14,00 V

-

Height Sens Pw Supply Val

Rear left height control sensor subassembly power supply voltage value

0 à 5,00 V

4,61 à 5,00 V

-

Rr Height Sens Signal Val

Rear left height control sensor subassembly signal value

0 à 5,00 V

0,50 à 4,50 V

Value changes depending on vehicle height

Front Right Wheel Speed Value

Front right wheel speed

0,00 à 260 km/h

Vehicle stopped: 0 km/h

-

Front Left Wheel Speed Value

Front left wheel speed

0,00 à 260 km/h

Vehicle stopped: 0 km/h

-

Vehicle Speed

Vehicle speed

0,00 à 260 km/h

Vehicle stopped: 0 km/h

-

Rear Height Adjust Value

Rear height adjustment offset value

0 à 1 023

The normal rear height adjustment value is displayed in this state (if a malfunction is detected, no value is displayed)

-

Rear Height Adjust Valid Flag

Rear height adjustment range

Valid or Invalid

Valid: Rear left height control sensor sub-assembly value is within normal range

Invalid: Rear left height control sensor sub-assembly value is outside normal range

-

Init Writing Count

Number of times initialization has been performed

0 à 255

Number of times initialization has been performed

-

Sensor Initialization Hist

Sensor initialization history

Non-compliant, 10%, 25%, 50%, 75%, 100% or Compliant

  • Not completed: Left headlight ECU subassembly not initialized after replacement.
  • 10%: Initialization completed with fuel tank filled to 10%
  • 25%: Initialization completed with fuel tank filled to 25%
  • 50%: Initialization completed with fuel tank filled to 50%
  • 75%: Initialization completed with fuel tank filled to 75%
  • 100%: Initialization completed with fuel tank filled to 100%
  • Compliant: ECU not replaced and ECU not initialized in the workshop.

-

+B Voltage Value

Left headlight ECU sub-assembly ignition power supply +B voltage value

0 à 19,75 V

11 à 14 V

-

Leveling Motor Target Position

Headlight Leveling Motor Target Position

0 à 102,3 %

10 à 90 %

-

Number Of Trouble Codes

Number of DTCs

0 à 255

Number of stored DTCs displayed

-

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / HL AutoLeveling / Active Test.

(e) Perform the Active Test by following the Techstream instructions.

Body Electrical > HL AutoLeveling > Active Test

Tester display

Item

Control Range

Diagnostic Note

Drive The Leveling Motor

Headlight levelling motor up or down operation

Stop/Down/Up

Perform the Active Test with the engine running and the vehicle stationary

Headlight Leveling Indicator

"Headlight System Malfunction Visit Your Dealer" displayed

ON or OFF

-