Exterior Lighting

Initialization

6steps
~36min
2/5difficulty
Done 0 of 6

INITIALIZATION

NOTICE:

  • The procedures required (adjustment, calibration, initialization or registration) that must be performed after the parts have been removed and installed or replaced during removal/installation of the left headlight ECU subassembly are listed below.

    Work performed or system conditions

    Necessary Procedures

    Proceed to

    Replacement of left headlight ECU subassembly

    Synchronize Vehicle Information

    SYNCHRONIZE VEHICLE INFORMATION

    Perform initialization of the Left Headlight ECU Sub-assembly

    INITIALIZATION OF LEFT HEADLIGHT ECU SUB-ASSEMBLY

    Replacement of the left rear height control sensor sub-assembly, removal and installation of the left rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed.

    Perform initialization of the Left Headlight ECU Sub-assembly

    INITIALIZATION OF LEFT HEADLIGHT ECU SUB-ASSEMBLY

  • A new left headlight ECU sub-assembly cannot operate until vehicle information is synchronized.
  • After replacing the left headlight ECU sub-assembly, it is necessary to perform vehicle information synchronization and initialization.
  • Even if the left headlight ECU sub-assembly is replaced with a new part, vehicle information synchronization and initialization are not necessary.
  • Adjust the headlight aim after initializing the left headlight ECU sub-assembly.
  • If a malfunction is detected in the headlight automatic leveling system, initialization of the left rear height control sensor sub-assembly signal is not possible. Perform troubleshooting before initialization.

SYNCHRONIZE VEHICLE INFORMATION

(a) When using the Techstream:

(1) Turn the ignition switch OFF.

(2) Connect the Techstream to the DLC3.

(3) Turn the ignition switch ON and check that the warning message "Headlight System Uninitialized Visit Your Dealer" is displayed on the multi-information display.

(4) Select the following menu items: Body Electrical / HL AutoLeveling / Utility / ECU Information Sync.

Body Electrical > HL AutoLeveling > Utility

ECU Information Sync

(5) Check the display on the Techstream and press "Next".

(6) Check that the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster flashes 6 times at 2 Hz.

(7) Press "Exit" and turn the ignition switch OFF.

NOTICE:

After vehicle information synchronization, reset the left headlight ECU sub-assembly.

HINT:

  • If the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster does not start flashing after performing step (v), repeat the procedure once more.
  • If the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster stops flashing and stays on, the left rear height control sensor sub-assembly may be malfunctioning.

(b) Without using the Techstream:

(1) Turn the ignition switch ON and check that the warning message "Headlight System Uninitialized Visit Your Dealer" is displayed on the multi-information display.

(2) Using the high beam/low beam switch, turn the low beams ON and OFF 8 times within 20 seconds after turning the ignition switch ON.

NOTICE:

If the low beams come on while the ignition switch is ON, shine a light on the automatic light control sensor to turn the low beams OFF before operating the high beam/low beam switch. (Light control switch in OFF position)

HINT:

If this step cannot be completed within 20 seconds, turn the ignition switch OFF. Then turn the ignition switch ON and repeat the procedure.

(3) Check that the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster flashes 6 times at 2 Hz.

HINT:

  • If the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster does not start flashing after performing step (ii), repeat the procedure once more.
  • If the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster stops flashing and stays on, turn the ignition switch OFF and then ON. If the warning message "Headlight System Malfunction Visit Your Dealer" is displayed for at least 5 seconds after the ignition switch is turned ON, the left rear height control sensor sub-assembly may be malfunctioning.

(4) Turn the ignition switch to OFF.

NOTICE:

After vehicle information synchronization, reset the left headlight ECU sub-assembly.

INITIALIZATION OF LEFT HEADLIGHT ECU SUB-ASSEMBLY

(a) Prepare the vehicle for initialization

(1) Unload the vehicle and check that the spare tire*1 or tire repair kit*2, tools and jack are in their original locations.

  • *1: with conventional spare tire

    *2: with tire repair kit

(2) Make sure there are no passengers in the vehicle.

(3) Turn the light control switch OFF.

(4) Park the vehicle on a flat surface and maintain the vehicle height.

(b) Check the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster.

(1) Turn the ignition switch ON and check the status of the warning message "Headlight System Malfunction Visit Your Dealer" on the multi-information display.

OK:

Condition

Specified Condition

The left headlight ECU sub-assembly has been replaced with a new part.

"Headlight System Malfunction Visit Your Dealer" flashes 6 times at 2 Hz.

Replacement of the left rear height control sensor sub-assembly, removal and installation of the left rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed.

"Headlight System Malfunction Visit Your Dealer" is not displayed on the multi-information display.

(c) Initialization (when using the Techstream)

(1) Turn the ignition switch OFF.

(2) Connect the Techstream to the DLC3.

(3) Turn the ignition switch to the ON position.

(4) Select the following menu items: Body Electrical / HL AutoLeveling / Utility / Height Sensor Initialization.

Body Electrical > HL AutoLeveling > Utility

Height Sensor Initialization

(5) Check the display on the Techstream and press "Next".

(6) Make sure the "Position ID" is correct for the fuel level according to the table below.

HINT:

The "Position ID" is determined by the remaining fuel level as shown below.

Fuel level

Position ID

Headlight aiming warning flashing frequency

In range A

EMPTY

1

In range B

1/4 to more than EMPTY

2

In range C

1/2 to more than 1/4

3

In range D

3/4 to more than 1/2

4

In range E

FULL to more than 3/4

5

(7) Select the appropriate "Position ID" option and press "Next".

(8) Press "Exit".

(9) Check the status of the warning message "Headlight System Malfunction Visit Your Dealer" on the instrument cluster.

Standard:

Condition

Specified Condition

The left headlight ECU sub-assembly has been replaced with a new part.

Flashes 6 times at 2 Hz → Flashes continuously N* times at 2 Hz.

Replacement of the left rear height control sensor sub-assembly, removal and installation of the left rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed.

Off → Flashes continuously N* times at 2 Hz.

HINT:

  • *: The number of flashes of the "Headlight System Malfunction Visit Your Dealer" warning message is determined by the selected "Position ID" option.
  • If initialization does not complete normally, repeat the initialization procedure from step (i).
  • If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the instrument cluster assembly, the left headlight ECU sub-assembly may be malfunctioning.

(10) Check that initialization completes normally, then turn the ignition switch OFF.

(d) Initialization (without using the Techstream)

(1) Turn the ignition switch to ON.

(2) Check the number of times the low beams are turned ON and OFF as specified.

HINT:

The number of times the low beams must be turned ON and then OFF is determined by the amount of fuel remaining, as shown below.

Fuel level

Number of times low beams must be turned ON then OFF

In range A

1

In range B

2

In range C

3

In range D

4

In range E

5

(3) Enter initialization mode. (with light control switch in OFF position)

  1. Turn the ignition switch and headlight beam switch to OFF.
  2. Cover the automatic light control sensor with an opaque object.
  3. Perform the following steps within 5 seconds.
    1. Turn the ignition switch ON.
    2. While pulling the headlight beam switch, move it from OFF to AUTO and back to OFF at least 3 times.

      HINT:

      Check that the parking lights turn on and off again.

    3. Set the headlight beam switch to OFF.

HINT:

  • Perform the above operation within 5 seconds.
  • When entering initialization mode, the "Headlight System Malfunction Visit Your Dealer" warning message on the instrument cluster starts flashing at 1 Hz.

(4) Enter initialization mode. (without light control switch in OFF position)

  1. Turn the ignition switch OFF.
  2. Shine a light onto the automatic light control sensor.
  3. Perform the following steps within 5 seconds.
    1. Turn the ignition switch ON.
    2. While pulling the headlight beam switch, move it from AUTO to TAIL and back to AUTO at least 3 times.

      HINT:

      Check that the parking lights turn on and off again.

    3. Set the headlight beam switch to AUTO.

HINT:

  • Perform the above operation within 5 seconds.
  • When entering initialization mode, the "Headlight System Malfunction Visit Your Dealer" warning message on the instrument cluster starts flashing at 1 Hz.

(5) Once in initialization mode, turn the low beams from OFF to ON, then back to OFF N* times.

HINT:

  • *: The number of times the headlight beam switch is changed from ON to OFF (N) is determined by the fuel level shown on the fuel gauge.
  • Turn the headlight beam switch ON and OFF within 20 seconds after entering initialization mode.
  • Turn the headlight beam switch ON and OFF at intervals of approx. 3 seconds.

(6) Check the status of the "Headlight System Malfunction Visit Your Dealer" warning message on the instrument cluster.

Standard:

Condition

Specified Condition

The left headlight ECU sub-assembly has been replaced with a new part.

Flashes 6 times at 2 Hz → Flashes continuously N* times at 2 Hz.

Replacement of the left rear height control sensor sub-assembly, removal and installation of the left rear height control sensor sub-assembly, replacement of the suspension, etc. have been performed.

Off → Flashes continuously N* times at 2 Hz.

HINT:

  • *: The flashing rate of the "Headlight System Malfunction Visit Your Dealer" warning message is determined by how often the low beams are turned ON and OFF.
  • If initialization does not complete normally, repeat the initialization procedure from step (i).
  • If the "Headlight System Malfunction Visit Your Dealer" warning message is displayed on the instrument cluster assembly, the left headlight ECU sub-assembly may be malfunctioning.

(7) Check that initialization completes normally, then turn the ignition switch OFF.