Exterior Lighting

Height control sensor malfunction (B2416,B241A)

~5min read

DESCRIPTION

This DTC is stored when the left headlamp ECU subassembly detects a malfunction in the power supply circuit of the rear left height control sensor subassembly or in the rear left height control sensor subassembly circuit. The left headlamp ECU subassembly stores DTC B2416 and B241A.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

B2416

Height control sensor malfunction

One of the following conditions is met

  • Malfunction in left rear height control sensor assembly
  • Open in left rear height control sensor assembly power supply circuit
  • Short in left rear height control sensor assembly power supply circuit
  • Rear LH Height Control Sensor Sub-assembly
  • Left Headlight ECU Subassembly
  • Wire harness or connector

-

B241A

Rear height control sensor

One of the following conditions is met

  • Malfunction in left rear height control sensor assembly
  • Open in left rear height control sensor assembly circuit
  • Short in left rear height control sensor assembly circuit
  • Rear LH Height Control Sensor Sub-assembly
  • Left Headlight ECU Subassembly
  • Wire harness or connector

-

DTC detection conditions (DTC B2416 and B241A):

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Diagnostic Condition

Ignition Switch in ON position

○

○

○

Malfunction Status

Malfunction in left rear height control sensor assembly

○

-

-

Open in left rear height control sensor assembly power supply circuit

-

○

-

Short in left rear height control sensor assembly power supply circuit

-

-

○

Detection Duration

-

-

-

Number of Trips

1 trip(s)

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Before performing this inspection, make sure the left rear height control sensor assembly is installed correctly.
  • If the left headlight ECU subassembly has been replaced, it is necessary to synchronize the vehicle information and reset the left headlight ECU subassembly.

    Click here

  • If any of the following operations is performed, the left headlamp ECU subassembly must be initialized.

    Click here

    • Replacement of rear left height control sensor subassembly
    • Removal/installation of rear left height control sensor subassembly
    • Work that changes vehicle height, such as replacement of suspension components

PROCEDURE

  1. CLEAR DTCs

(a) Clear the DTCs.

Click here

Body Electrical > HL AutoLeveling > Clear DTCs
NEXT
  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Check the DTCs.

Click here

Body Electrical > HL AutoLeveling > Trouble Codes

OK:

DTCs B2416 or B241A are not output.

OK

USE SIMULATION METHOD TO CHECK

NG
  1. CHECK VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / HL AutoLeveling / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > HL AutoLeveling > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Height Sens Pw Supply Val

Rear left height control sensor subassembly power supply voltage value

0 à 5,00 V

4,61 à 5,00 V

-

Rr Height Sens Signal Val

Rear left height control sensor subassembly signal value

0 à 5,00 V

0,50 à 4,50 V

Value changes depending on vehicle height

Body Electrical > HL AutoLeveling > Data List

Tester display

Height Sens Pw Supply Val

Rr Height Sens Signal Val

OK:

The normal condition shown above is displayed.

OK

REPLACE LEFT HEADLIGHT ECU SUBASSEMBLY

NG
  1. CHECK HARNESS AND CONNECTOR (LH HEADLIGHT ECU ASSEMBLY - LEFT REAR HEIGHT CONTROL SENSOR ASSEMBLY)

(a) Disconnect the A16 connector from the LH headlight ECU sub-assembly.

(b) Disconnect the O2 connector from the left rear height control sensor assembly.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

A16-16 (SBR) - O2-3 (SHB)

Always

Below 1 Ω

A16-17 (SHRL) - O2-2 (SHRR)

Always

Below 1 Ω

A16-15 (SGR) - O2-1 (SHG)

Always

Below 1 Ω

A16-16 (SBR) or O2-3 (SHB) - Body ground

Always

10 kΩ minimum

A16-17 (SHRL) or O2-2 (SHRR) - Body ground

Always

10 kΩ minimum

A16-15 (SGR) or O2-1 (SHG) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. INSPECT LEFT REAR HEIGHT CONTROL SENSOR ASSEMBLY

(a) Remove the left rear height control sensor assembly.

Click here

(b) Inspect the left rear height control sensor assembly.

Click here

OK:

The left rear height control sensor assembly is normal.

OK

REPLACE LEFT HEADLIGHT ECU SUBASSEMBLY

NG

REPLACE LEFT REAR HEIGHT CONTROL SENSOR ASSEMBLY