Theft Deterrent / Keyless Entry

System Description

~9min read

SYSTEM DESCRIPTION

THEFT DETERRENT SYSTEM GENERAL DESCRIPTION

  • The theft deterrent system can be armed by locking the doors by performing one of the following operations:
    • Locking operation upon door opening*1
    • Remote door locking operation
    • *1: with Smart Key System
  • In the armed state, the alarm function will be activated when one of the following conditions is met:
    • One of the doors is unlocked.
    • One of the doors or the hood is open.
  • While the alarm is sounding, the system flashes the hazard warning lights. At the same time, the system activates the vehicle horn and the audible alarm unit to signal the intrusion and warn people near the vehicle.
  • The theft deterrent system can be canceled by unlocking the doors using one of the following operations:
    • Locking operation upon door opening*1
    • Remote door locking operation
    • Key-linked locking function*2
    • *1: with Smart Key System
    • *2: This function is activated via the customization function.

      Click here

  • The theft deterrent system has an active arming mode. There are 4 states in this mode: disarmed state, arming preparation state, armed state and alarm sounding state.

(a) Disarmed state:

  • The alarm function is deactivated.
  • The theft deterrent system is deactivated.

(b) Arming preparation state:

  • Time required for the system to change to the armed state.
  • The theft deterrent system is deactivated.

(c) Armed state:

  • The theft deterrent system is activated.

(d) Alarm sounding state:

  • The alarm function is activated.

Alarm duration:

Approximately 27.5 seconds

Alarm methods

Alarm method

Turn signal lights

Flashes

Vehicle horns

Sounding

(Cycles of approximately 0.4 seconds)

Audible alarm unit

Sounding

(Cycles of approximately 0.4 seconds)

FUNCTION OF MAIN COMPONENTS

Component

Function

Immobilizer Indicator

Informs the driver of the theft deterrent system status.

Audible alarm unit

Sounds when an attempted break-in or theft is detected.

Turn signal lights

Flash when an attempted break-in or theft is detected.

Vehicle horns

Sounds when an attempted break-in or theft is detected.

  • Front left/right door sill light switch assembly
  • Rear door (left/right) courtesy light switch assembly
  • Luggage compartment door sill light switch

Detects the door status (open or closed)

Door unlock detection switch

Detects the door status (locked or unlocked).

Engine compartment sill light switch (hood lock assembly)

Detects the hood status (open or closed).

Certification ECU (smart key ECU assembly)*1

  • Receives the remote door lock/unlock signal.
  • Receives the remote door lock/unlock signal.

Main body ECU (multiplex network body ECU)*2

Receives the remote door lock/unlock signal.

  • *1: with Smart Key System
  • *2: Without smart key system

ACTIVE ARMING MODE

(a) Active arming mode:

This system is activated as shown in the diagram below when one of the items in each condition occurs.

HINT:

The term "all doors" used in this section refers to the driver's door, front passenger door, rear left door, rear right door and luggage compartment door.

with Smart Key System

Condition

Item

Condition [1]

In disarmed state 1, when the engine switch is in the OFF position, the system changes state if the following condition is met:

  • With all doors and the hood closed, all doors are locked by a remote operation, the smart key system.

Condition [2]

  • Approximately 30 seconds elapse.

Condition [3]

  • All doors are unlocked by a remote operation, the smart key system or the key-linked central door locking.
  • One of the doors is unlocked.
  • A door is opened.
  • The engine switch is pushed.
  • The engine switch is set to ON (ACC) or ON (IG).
  • The battery is reconnected.

Condition [4]

  • The hood is opened after it has been closed.
  • The battery is reconnected while one of the doors or the hood is open or a door is unlocked.
  • A door is opened while all doors are closed.
  • One of the doors is unlocked while all the others are locked.
  • When 5 seconds or more have elapsed after pressing the engine switch, the power mode changes from OFF or ON (IG) without pressing the engine switch.
  • The hood is opened.
  • A door is opened.
  • The power mode is ON (IG).

Condition [5]

  • The engine switch is set to ON (IG) and the engine runs at 550 rpm for at least 2 seconds.
  • All doors are unlocked by a remote operation, the smart key system or the key-linked central door locking.

Condition [6]

  • After approximately 27.5 seconds, the alarm stops and the system returns to the armed state.

Condition [7]

  • The hood is closed after it has been opened.

Condition [8]

  • One of the doors is unlocked while all the others are locked.
  • A door is opened.
  • The engine switch is pushed.
  • The engine switch is set to ON (ACC) or ON (IG).
  • The battery is reconnected.
  • All doors are unlocked by a remote operation, the smart key system or the key-linked central door locking.

Condition [9]

In disarmed state 1, when the engine switch is in the OFF position, the system changes state if the following condition is met:

  • With all doors closed and the hood open, all doors are locked by a remote operation, the smart key system or a key-linked central door locking operation.

Condition [10]

  • The hood is opened.
without Smart Key System

Condition

Item

Condition [1]

In disarmed state 1, when the ignition switch is in the OFF position, the system changes state if the following condition is met while the key is not in the key cylinder:

  • With all doors and the hood closed, all doors are locked by remote operation.

Condition [2]

  • Approximately 30 seconds elapse.

Condition [3]

  • All doors are unlocked using the remote control or the key-linked central door locking operation.
  • One of the doors is unlocked.
  • A door is opened.
  • A key is inserted into the ignition key cylinder.
  • The ignition switch is set to ACC or ON.
  • The battery is reconnected.

Condition [4]

  • The hood is opened after it has been closed.
  • The battery is reconnected with the hood open or a door unlocked.
  • A door is opened while all doors are closed.
  • One of the doors is unlocked while all the others are locked.
  • The ignition switch is in the ON position while the key is not in the ignition key cylinder.
  • The hood is opened.
  • A door is opened.

Condition [5]

  • The engine switch is set to ON (IG) and the engine runs at 550 rpm for at least 2 seconds.
  • All doors are unlocked using the remote control or the key-linked central door locking operation.

Condition [6]

  • After approximately 27.5 seconds, the alarm stops, and 5 seconds later, the system rearms.

Condition [7]

  • The hood is closed after it has been opened.

Condition [8]

  • One of the doors is unlocked while all the others are locked.
  • A door is opened.
  • A key is inserted into the ignition key cylinder.
  • The ignition switch is set to ACC or ON.
  • The battery is reconnected.
  • All doors are unlocked using the remote control or the key-linked central door locking operation.

Condition [9]

In disarmed state 1, when the ignition switch is in the OFF position, the system changes state if the following condition is met while the key is not in the key cylinder:

  • With all doors closed and the hood open, all doors are locked remotely.

Condition [10]

  • The hood is opened.

DOOR FORCED LOCK CONTROL

(a) The door forced lock control is intended to prevent vehicle theft. Immediately after a door is unlocked (armed state), a door forced lock signal automatically locks all doors.

(1) The door forced lock control is operated if the following conditions are met:

  • The anti-theft system is in the armed state.
  • One of the doors is unlocked.

SECURITY INDICATOR SIGNAL OUTPUT

(a) Depending on the status of the anti-theft system, the main body ECU (multiplex network body ECU) outputs a signal to operate the security indicator. However, some actual security indicator illumination conditions differ from the signals output by the main body ECU (multiplex network body ECU).

Output

Anti-theft system status

Immobilizer Indicator

Output signal from main body ECU (multiplex network body ECU)

Actual illumination status

Disarmed status (1), (2)

OFF

  • Off (immobilizer system deactivated)
  • Flashing (immobilizer system activated)

Arming preparation status

ON

ON

Armed status

OFF

Flashes

Alarm sounding status

ON

ON

Flashing cycle

Time

Immobilizer Indicator

0,125 s

ON

1,875 s

OFF

HINT:

When the immobilizer system is activated, the security indicator flashes in the disarmed and armed states, due to the signals output by the immobilizer system.