Theft Deterrent / Keyless Entry

Malfunction

~12min read

DESCRIPTION

If the anti-theft system activates on its own, this may be caused by, for example, a short circuit in the courtesy light switch of one of the doors or the hood, causing an erroneous signal to be sent.

HINT:

Preconditions for arming preparation:

  • The ignition switch is in the OFF position, all doors and the hood are closed, and all doors are locked using the remote control or by the door lock operation*1.
    • *1: with Smart Key System

WIRING DIAGRAM

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

  • Before replacing the main body ECU (multiplex network body ECU), refer to the REGISTRATION section*1.

    Click here

    *1: with Smart Key System

  • The theft deterrent system uses the CAN communication system. Check the communication function by following the procedure described in the HOW TO USE TROUBLESHOOTING section. Perform troubleshooting of the theft deterrent system only after confirming that the communication systems operate correctly.

    Click here

  • While using the Techstream with the vehicle engine switch OFF, connect the Techstream to the DLC3 and turn a welcome light switch ON and OFF at intervals of no more than 1.5 seconds until communication between the Techstream and the vehicle starts. Then select the vehicle type in manual mode and enter the following menus: Body Electrical / Smart Key. While using the Techstream, regularly switch a welcome light switch between ON and OFF at intervals of no more than 1.5 seconds to maintain communication between the Techstream and the vehicle.
  • If the vehicle or vehicle controls are operated (for example, during inspection when the vehicle is brought in for repairs) before the operation history is read and recorded, the operation history information may be lost.
  • The "Read Operation History" function uses the current system time setting in Techstream and the clock in the inspection ECU to calculate the times shown in the operation history. For this reason, before reading the operation history, first make sure the Techstream system clock is set accurately to the current time.

PROCEDURE

  1. ANALYZE THE PROBLEM DESCRIBED BY THE CUSTOMER AND CONFIRM THE SYMPTOMS

HINT:

  • When troubleshooting, make sure the symptoms of the problem have been correctly identified. Any preconceptions must be set aside in order to make an accurate judgment. To clearly understand the actual symptoms of the problem, it is essential to ask the customer about the nature of the problem and the conditions under which it occurred.
  • Gather as much information as possible for reference. Previous problems that do not appear related to the current problem may also be very useful in some cases.
  • The 5 items listed below are essential for performing an accurate analysis of the problem:

    What?

    Vehicle model, system name

    When?

    Date, time, frequency of occurrence, whether the problem appeared recently or has been occurring for a long time

    Where?

    If the problem occurs at a specific location

    What were the conditions?

    Whether the doors are locked or unlocked, whether the ignition switch is in the ON position, whether the engine is running

    How did it happen?

    Symptoms of the problem*

    • *: Be sure to ask the customer to describe the following points in very precise detail: the vehicle operating conditions, the environment, and the problem. Then check the DTCs.
NEXT
  1. CHECK THE THEFT DETERRENT SYSTEM OPERATION HISTORY

(a) Based on the customer interview, use the Techstream to check the theft deterrent system operation history around the time the malfunction occurred, as reported by the customer. Check whether the most recent operation history record of the theft deterrent system is close to the time the problem was reported to occur.

(1) On the Techstream screen, select the following menus: Body / Main Body / Utility / Operation History Analysis. Read the operation history according to the Techstream display.

Click here

(2) Confirm that there is a theft deterrent system operation history matching what the customer reported.

Click here

HINT:

Based on the operation history display, perform the vehicle-side inspection and carry out repairs if a problem is found. If the vehicle has no malfunction, ask the customer to describe the probable causes as "driver" or "environment / other than driver".

Result:

Result

Proceed to

There is an operation history close to the time of the malfunction reported by the customer, but the malfunction could not be identified even by following the instructions to check the corresponding components.

A

There is an operation history close to the time of the malfunction reported by the customer, and by following the instructions to check the corresponding components, the malfunction was identified.

B

There is no operation history around the time the malfunction supposedly occurred, according to the customer.

C

B

GO TO STEP 12

C

END

A
  1. INSPECT SECURITY INDICATOR OPERATION

(a) When the theft deterrent system is in the ready-to-arm state, make sure the security indicator light is on.

Click here

(b) When the theft deterrent system is in the armed state, make sure the security indicator light is flashing.

Click here

Anti-theft system status

Content

Security indicator light status

Disarmed status (1), (2)

The theft deterrent system is deactivated.

  • Off (immobilizer system deactivated)
  • Flashing (immobilizer system activated)

Arming preparation status

Waiting period after the theft deterrent system activation conditions are met but before the system is actually armed (approximately 30 seconds).

(theft detection not performed)

ON

Armed status

The theft deterrent system is deactivated.

(theft detection possible)

Flashing (immobilizer system activated)

Alarm sounding status

When a theft attempt is detected, the alarm sounds using the turn signal lights, the alarm buzzer assembly and the vehicle horn.

(the alarm sounds for 27.5 seconds)

ON

NG

GO TO THE OTHER PROBLEM

OK
  1. CHECK VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ACC SW

Ignition Switch ACC Position Signal

ON or OFF

ON: Ignition switch in ACC position.

OFF: Ignition switch in OFF position

-

IG SW

Ignition Switch ON Position Signal

ON or OFF

ON: Ignition switch in ON position

OFF: Ignition switch in OFF or ACC position.

-

Body Electrical > Main Body > Data List

Tester display

ACC SW

IG SW

OK:

The normal conditions listed above are displayed.

NG

GO TO ILLUMINATION SYSTEM

OK
  1. CHECK VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

FR Door Lock Pos

Front Right Door Unlock Detection Switch

LOCK or UNLOCK

LOCK: Front right door locked.

UNLOCK: Front right door unlocked.

-

FL Door Lock Pos

Front Left Door Unlock Detection Switch

LOCK or UNLOCK

LOCK: Front left door locked.

UNLOCK: Front left door unlocked.

-

RR-Door Lock Pos SW

Rear Right and Left Door Unlock Detection Switch

ON or OFF

ON: Rear right or left door unlocked.

OFF: Rear right and left doors locked.

-

RL-Door Lock Pos SW

Rear Right and Left Door Unlock Detection Switch

ON or OFF

ON: Rear right or left door unlocked.

OFF: Rear right and left doors locked.

-

Body Electrical > Main Body > Data List

Tester display

FR Door Lock Pos

FL Door Lock Pos

RR-Door Lock Pos SW

RL-Door Lock Pos SW

NG

GO TO ILLUMINATION SYSTEM

OK
  1. CHECK VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

RR Door Courtesy SW

Right Rear Door Courtesy Light Switch Assembly

ON or OFF

ON: Right rear door open.

OFF: Right rear door closed.

-

RL Door Courtesy SW

Left Rear Door Courtesy Light Switch Assembly

ON or OFF

ON: Left rear door open.

OFF: Left rear door closed.

-

FR Door Courtesy SW

Front Right Door Courtesy Light Switch Assembly

ON or OFF

ON: Front RH door open

OFF: Front RH door closed

-

FL Door Courtesy SW

Front left door courtesy light switch assembly

ON or OFF

ON: Front left door open

OFF: Front left door closed

-

Body Electrical > Main Body > Data List

Tester display

RR Door Courtesy SW

RL Door Courtesy SW

FR Door Courtesy SW

FL Door Courtesy SW

OK:

The normal conditions listed above are displayed.

NG

GO TO ILLUMINATION SYSTEM

OK
  1. CHECK VALUE USING TECHSTREAM

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Back Door Courtesy SW

Luggage compartment door sill light switch

ON or OFF

ON: Back door open.

OFF: Back door closed.

-

Body Electrical > Main Body > Data List

Back Door Courtesy SW

OK:

The normal conditions listed above are displayed.

NG

GO TO ILLUMINATION SYSTEM

OK
  1. READ VALUE USING TECHSTREAM (HOOD COURTESY SW)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Main Body / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Main Body > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Hood Courtesy SW

Hood Courtesy Light Switch Assembly

ON or OFF

ON: Hood open.

OFF: Hood closed.

-

Body Electrical > Main Body > Data List

Hood Courtesy SW

OK:

The Techstream display changes correctly according to the state of the engine room courtesy light switch (Hood Lock Assembly).

NG

GO TO STEP 10

OK
  1. CUSTOMER INTERVIEW

(a) If the symptom cannot be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electronic key transmitter sub-assembly (electronic key) for the appropriate date/time in the operation history.

Click here

Standard:

The cause has been identified

OK

END

NG

CHECK FOR INTERMITTENT PROBLEMS

  1. INSPECT ENGINE ROOM COURTESY LIGHT SWITCH (HOOD LOCK ASSEMBLY)

(a) Remove the engine room courtesy light switch (Hood Lock Assembly).

Click here

(b) Inspect the engine room courtesy light switch (Hood Lock Assembly).

Click here

NG

REPLACE ENGINE ROOM COURTESY LIGHT SWITCH (HOOD LOCK ASSEMBLY)

OK
  1. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU) - ENGINE ROOM COURTESY LIGHT SWITCH (HOOD LOCK ASSEMBLY) - BODY GROUND)

(a) Disconnect the F15 connector from the main body ECU (multiplex network body ECU).

(b) Disconnect connector A8 from the engine room courtesy light switch (Hood Lock Assembly).

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F15-11 (HCTY) - A8-1 (+)

Always

Below 1 Ω

F15-11 (HCTY) or A8-1 (+) - Body ground

Always

10 kΩ minimum

A8-2 (E) - Body ground

Always

Below 1 Ω

OK

REPLACE MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CUSTOMER INTERVIEW

(a) If the symptom cannot be confirmed or reproduced, after explaining this to the customer, also explain the history of input signals from the electronic key transmitter sub-assembly (electronic key) for the appropriate date/time in the operation history.

Click here

Standard:

The cause has been identified

OK

END

NG

CHECK FOR INTERMITTENT PROBLEMS