Body centre, roof, frame. Roof

In this manual: Body centre, roof, frame. Roof
Technical data. Panel gaps - front — 1Body front. Lock carrier — 1Body front. Wings — 1Body front. Bulkhead — 1Bonnet, flaps, cab, central locking. Bonnet — 1Bonnet, flaps, cab, central locking. Rear lid — 1Bonnet, flaps, cab, central locking. Charging flap unit — 1Front door, central locking. Door — 1Front door, central locking. Door components — 1Front door, central locking. Central locking — 1Rear door,sliding door,wing doors,central locking. Door — 1Rear door,sliding door,wing doors,central locking. Door components — 1Sliding roof. Sliding sunroof — 1Bumper. Bumper, front — 1Bumper. Bumper, rear — 1Glazing & window mechanism. Repair notes — 1Glazing & window mechanism. Windscreen — 1Glazing & window mechanism. Rear windscreen — 1Glazing & window mechanism. Side windows — 1Glazing & window mechanism. Door windows — 1Exterior equipment. Spoiler — 1Exterior equipment. Mouldings, trims, extensions — 1Exterior equipment. Underbody cladding — 1Exterior equipment. Roof moulding and roof railing — 1Exterior equipment. Exterior mirror — 1Exterior equipment. Wheel housing liner — 1Exterior equipment. Lettering and emblems — 1Exterior equipment. Bicycle carrier — 1Exterior equipment. Trim film and protective film — 1Interior equipment. Compartments & covers — 1Interior equipment. Equipment — 1Interior equipment. Centre console — 1Interior equipment. Front centre armrest — 1Interior equipment. Interior mirror — 1Passenger protection. Seat belts — 1Passenger protection. Child seat anchors — 1Passenger protection. Airbag system — 1Passenger protection. Airbag control unit — 1Passenger protection. Front airbag, driver side — 1Passenger protection. Front passenger airbag — 1Passenger protection. Side airbags — 1Passenger protection. Curtain airbags — 1Passenger protection. Airbag crash sensors — 1Passenger protection. Seat occupied recognition — 1Trim, noise insulation. Front door trims — 1Trim, noise insulation. Rear door trims — 1Trim, noise insulation. Dash panel — 1Trim, noise insulation. Central tube for dash panel — 1Trim, noise insulation. Interior trims — 1Trim, noise insulation. Roof trims — 1Trim, noise insulation. Luggage compartment trims — 1Seat frames. Overview of seat variants — 1Seat frames. Front seats — 1Seat frames. Rear seats — 1Seat padding, covers. Front seat covers and padding — 1Seat padding, covers. Rear seat covers and padding — 1Vehicle-specific paintwork information. Explanation of symbols — 1Vehicle-specific paintwork information. Paintwork structure — 1Vehicle-specific paintwork information. Areas exposed to stone chipping — 1Vehicle-specific paintwork information. Masked sectors — 1Vehicle-specific paintwork information. Seam sealing — 1Vehicle-specific paintwork information. Underseal — 1Vehicle-specific paintwork information. Cavity sealing — 1Vehicle-specific paintwork information. Contrasting colours — 1Vehicle-specific paintwork information. Paintwork repair — 1Technical data. Acoustic considerations during vehicle development — 1Technical data. General procedure for identifying noises — 1Technical data. Volkswagen equipment for localising noises — 1Technical data. Borescope VAS 6748A — 1Technical data. Causes — 1Technical data. Locating water ingress — 1Technical data. Attachments — 1Technical data. Vehicle identification data — 1Technical data. Safety information — 1Technical data. Body parts and materials — 1Technical data. Alignment jig — 1Body front. Longitudinal member cross panel — 1Body front. Longitudinal member — 1Body front. Front wheel housing — 1Body centre, roof, frame. Roof — 1Body centre, roof, frame. A-pillar — 1Body centre, roof, frame. B-pillar — 1Body centre, roof, frame. Side member — 1Body, rear. Rear cross member — 1Body, rear. Rear cross panel — 1Body, rear. Luggage compartment floor — 1Body, rear. Rear longitudinal member — 1Body, rear. Side panel — 1Body, rear. Rear wheel housing — 1General information, Body. Basic information on body repairs — 1General information, Body. Explanation of symbols — 1General information, Body. Overview of materials used — 1General information, Body. Joining and separating techniques — 1General information, Body. Surface repair — 1General information, Body. Corrosion protection — 1General information, Body. Noise insulation — 1General information, Body. Plastic repair — 1General information, Body. Welding plastic attachments — 1General information, Body. General notes – windows — 1General information, Body. Glass repair — 1General information, Body. Use of adhesives — 1General information, Body. Self-adhesive components — 1General information, Body. Noises — 1General information, Body. Preparing for disposal — 1General information, Body. Leaks — 1General information, paint. Safety information — 1General information, paint. General information — 1Genuine products. Filler — 1Genuine products. Priming metal — 1Genuine products. Priming plastic materials — 1Genuine products. Surfacer — 1Genuine products. 2-pack top coats — 1Repair painting work. Paint finish – decorative strips and films — 1Repair painting work. Tips and tricks — 1Air conditioner. Overview of fitting locations — 1Air conditioner. Refrigerant circuit — 1Air conditioner. Valve unit of heat pump — 1Air conditioner. Air conditioner compressor — 1Air conditioner. Control motors — 1Air conditioner. Front heater and air conditioning unit — 1Air conditioner. Air duct — 1Air conditioner. Coolant circuit — 1Air conditioner. Other controlling and regulating components — 1Air conditioner. Air quality improvement system — 11-speed gearbox 0MH, rear, EQ310. Technical data — 11-speed gearbox 0MH, rear, EQ310. Gearbox mechanics,operation, construction,diff — 11-speed gearbox 0MH, rear, EQ310. Final drive, differential, differential lock — 1General information. High voltage — 1Electric drive EIP220, EIA200, EIA210. Technical data — 1Electric drive EIP220, EIA200, EIA210. Engine assy,cylinder block,crankcase — 1Electric drive EIP220, EIA200, EIA210. Engine cooling — 1Electric drive. High-voltage components, charging unit and voltage converter — 1Electric drive. Warning stickers — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing without wax — 1Electric drive. High-voltage battery unit, edge of upper part of battery housing with wax — 1Electric drive. Power and control electronics for electric drive — 1Electric drive. Electric drive motor — 1Electric drive. Motor control unit — 1Electric drive. De-energising high-voltage system — 1Electric drive. Re-energise high-voltage system — 1Electric drive. Potential equalisation lines — 1Electric drive. Charging socket, with charging cable — 1Electric drive. Charging socket, with separate charging cable — 1Electric drive. Charging unit for high-voltage battery — 1Electric drive. Charging unit for high-voltage battery, with integrated voltage converter — 1Electric drive. Vehicle noise & engine sound — 1Electric drive. Accelerator pedal — 1Electric drive. Voltage converter — 1Electric drive. High-voltage cables, all-wheel drive — 1Electric drive. High-voltage cables, rear-wheel drive — 1Front suspension, drive shafts. Front axle — 1Front suspension, drive shafts. Subframe — 1Front suspension, drive shafts. Suspension strut, upper suspension link — 1Front suspension, drive shafts. Lower suspension link, swivel joint — 1Front suspension, drive shafts. Wheel bearing — 1Front suspension, drive shafts. Anti-roll bar — 1Rear suspension, drive shaft. Rear axle — 1Rear suspension, drive shaft. Subframe — 1Rear suspension, drive shaft. Anti-roll bar — 1Rear suspension, drive shaft. Suspension link, track rod — 1Rear suspension, drive shaft. Suspension strut, shock absorber, spring — 1Rear suspension, drive shaft. Wheel bearing assembly, trailing arm — 1Rear suspension, drive shaft. Drive shaft — 1Self-levelling air spring system. Electronically controlled damping — 1Self-levelling air spring system. Vehicle level sender — 1Wheels, tyres. axle align. Wheel alignment — 1Wheels, tyres. axle align. Wheels, tyres — 1Steering. Steering wheel — 1Steering. Steering column — 1Steering. Steering rack — 1Brake system. Technical data — 1ABS, ADR, TCS, EDL, ESP. Overview of fitting locations — 1ABS, ADR, TCS, EDL, ESP. Control unit and hydraulic unit — 1ABS, ADR, TCS, EDL, ESP. Sensors — 1Brake, brake mechanics. Front brake — 1Brake, brake mechanics. Rear brake — 1Brake, brake mechanics. Parking brake — 1Brake, brake mechanics. Brake pedal — 1Brakes, hydraulics, regulator, servo. Brake servo and brake master cylinder — 1Brakes, hydraulics, regulator, servo. Hydraulic system — 1Wheels and Tyres Guide. Wheels, tyres. axle align — 1Wheels, tyres. axle align. Instructions on using the guide — 1Wheels, tyres. axle align. Legislative and technical conditions — 1Wheels, tyres. axle align. Wheel change — 1Wheels, tyres. axle align. Fitting tyre — 1Wheels, tyres. axle align. Wheel bolts — 1Wheels, tyres. axle align. Information on tyres — 1Wheels, tyres. axle align. Handling problems — 1Wheels, tyres. axle align. Evaluating tyres — 1Wheels, tyres. axle align. Tyre wear — 1Starter-current supply-CC. Battery — 1Instruments, GCI. Dash panel insert — 1Instruments, GCI. Horn — 1Windscreen wipewash system. Windscreen wiper system — 1Windscreen wipewash system. Windscreen washer system — 1Windscreen wipewash system. Rear window wiper system — 1Windscreen wipewash system. Rear window washer system — 1Lights, lamps, switches outside. LED headlight — 1Lights, lamps, switches outside. LED matrix headlight — 1Lights, lamps, switches outside. Tail lights — 1Lights, lamps, switches outside. Lights in exterior mirror — 1Lights, lamps, switches outside. Number plate light — 1Lights, lamps, switches outside. Entry and start authorisation system — 1Lights, lamps, switches outside. Steering column switch module — 1Lights, lamps, switches outside. Towing bracket — 1Lights, lamps, switches inside, anti-theft system. Lights — 1Lights, lamps, switches inside, anti-theft system. Controls — 1Lights, lamps, switches inside, anti-theft system. Anti-theft alarm system — 1Lights, lamps, switches inside, anti-theft system. Cigarette lighter, socket — 1Wiring. Relay carriers, fuse holders, electronics boxes — 1Wiring. Control units — 1Infotainment. Componentscontrol units — 1Infotainment. Multifunction steering wheel — 1Driver assist systems. Senders, sensors, control units — 1Driver assist systems. Adaptive cruise control — 1Driver assist systems. Reversing camera system — 1Driver assist systems. Front camera for driver assist systems — 1Driver assist systems. Overhead view camera — 1Electrical system. Starter-current supply-CC — 1Electrical system. Windscreen wipe and wash system — 1Wiring. Wires and lines — 1
~14min read
  • Assembly overview – vehicle without glass panel
  • Assembly overview – vehicle with glass panel
  • Assembly overview – roof side member
  • Renewing roof – vehicle without glass panel
  • Renewing roof - vehicle with glass panel
  • Renewing roof side member

Assembly overview – vehicle without glass panel

Assembly overview – vehicle without glass panel

1 - Roof

❏ → Rep. gr.51; Renewing roof – vehicle without glass panel

2 - Laser-soldered seams

3 - Bonded areas

Assembly overview – vehicle with glass panel

Assembly overview – vehicle with glass panel

1 - Roof

❏ → Rep. gr.51; Renewing roof - vehicle with glass panel

2 - Laser-soldered seams

3 - Bonded areas

Assembly overview – roof side member

Assembly overview – roof side member

Overview is shown for left side of vehicle as an example.

1 - Roof side member

❏ → Rep. gr.51; Renewing roof side member

2 - Roof carrier reinforcements

3 - Separating cut

❏ Parting cut can be combined with others in cases where extent of damage requires multiple cuts.

4 - Gas strut reinforcement

5 - Moulded foam inserts

❏ → Rep. gr.00; Moulded foam inserts

6 - Bonded areas

❏ Parting cut can be combined with others in cases where extent of damage requires multiple cuts.

7 - Separating cut

❏ Parting cut can be combined with others in cases where extent of damage requires multiple cuts.

8 - Separating cut

❏ Parting cut can be combined with others in cases where extent of damage requires multiple cuts.

Renewing roof – vehicle without glass panel

Renewing roof – vehicle without glass panel

WARNING

Gases/ vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

– Do not weld, solder or cut closer than 15 mm to moulded foam inserts.

– Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

– Only make separating cuts with body saw.

– Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

– RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

– New part must be welded in within 90 minutes.

NOTICE

Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.

– After bonding, the vehicle must not be moved and left at room temperature (at least 15 °C) for 8 to 10 hours.

– During this time, the vehicle must be standing on a level surface.

Observe safety information → Rep. gr.00; Safety information

Only tools and workshop equipment authorised by Volkswagen AG may be used → Rep. gr.00; Tools.

Removing

– Apply duct tape to left and right roof members parallel to laser brazing seams.

– Roughly cut roof -1- out parallel to laser solder seams -2-.

– Separate original joint.

– Remove roof -1-.

– Remove remaining material -1-. Do not damage roof side member.

– Carefully remove remaining material of laser soldered seam from left and right roof side members.

– Completely remove adhesive residue.

– Sand bonding and welding surfaces down to bare metal, and clean them.

– Apply corrosion protection measures to left and right roof side members ⇒ Body, General paint information, Technical data, General information; Pre-treatment of bonded surfaces using 2-component epoxy filler when replacing laser-welded roofs.

– Grind bonding surface for 2-pack body adhesive -1- down to bare metal and clean.

– Implement corrosion protection measures on sand-through spots of bonding surface for 1-component assembly adhesive -2- General paint information – passenger vehicles; Repair group 00; General information; Pre-treatment of bonding surfaces when renewing laser-welded roofs.

– Apply glass/paint primer to bonding surface for 1-pack assembly adhesive -2-.

Installing

Replacement parts

♦ For allocation of 1-pack assembly adhesive, see → Electronic parts catalogue (ETKA)

♦ For allocation of 2-pack body adhesive, see → Electronic parts catalogue (ETKA)

♦ For allocation of adhesive sealant, see → Electronic parts catalogue (ETKA)

♦ For allocation of glass/paint primer, see → Electronic parts catalogue (ETKA)

♦ For allocation of felt strips, see → Electronic parts catalogue (ETKA)

Important

● Adhesive sealants must be applied quickly.

● It is essential to take account of the processing time (pot life) of adhesives.

Important

● New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.

– Grind welding surfaces and bonding surfaces on new part -1- and -2- down to bare metal and clean.

– Clean bonding surfaces -2- for 1-component assembly adhesive parallel to roof flange on left and right of new part -1-.

– Apply glass/paint primer to bonding surfaces -2- for 1-pack assembly adhesive.

– Cut approx. 2 mm off nozzle -B- to provide appropriate bead geometry.

– Apply 1-component assembly adhesive to roof cross member.

– Apply 1-component assembly adhesive to left and right roof side members according to dimensions -a-, -b- and -c-.

♦ Dimension -a- = 10 mm

♦ Dimension -b- = 14 mm

– Apply 1-component assembly adhesive to inside of new part -1- parallel to roof flange on left and right according to dimensions -a- and -b-.

♦ Dimension -a- = 14 mm

♦ Dimension -b- = 12 mm

– Cut off first step of static mixer -A- to achieve corresponding bead cross-section.

– Carefully operate double cartridge gun without static mixer until 2-component body adhesive is discharged uniformly from both chambers of connecting piece.

– Screw static mixer onto connecting piece.

– Discharge the first 100 mm of 2-component body adhesive onto a piece of cardboard and only then begin to apply the adhesive to the vehicle.

– Fill 2-component body adhesive in area of roof side members.

– Apply 2-component body adhesive to entire surface.

– Completely coat flanges of new part -1- with 2-component body adhesive.

– Adapt new part -1- to fit and fix in position.

NOTICE

Risk of damage from overtensioning

– Do not overtighten tensioning straps.

– In areas shown, tension tensioning straps -2- transversely over roof to vary height of roof.

– Check dimension -a- on roof to roof side members.

♦ Dimension -a-= 6.0 mm ± 0.5 mm

– Fix position of new part -1- on front roof cross member and rear roof cross member using mole grips.

– If necessary, place felt strips underneath for compensation.

– Excessive 2-component body adhesive must be removed immediately.

– Weld in new part -1- (RP spot weld seam).

– Remove surplus 2-component body adhesive -4- immediately.

– Apply a thin coat of adhesive sealant onto seam between new part -1- and roof side member -5- to form a fine seam seal -2-.

– Adhesive bead -3- must seal off the interior.

Renewing roof - vehicle with glass panel

Renewing roof - vehicle with glass panel

WARNING

Gases/ vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

– Do not weld, solder or cut closer than 15 mm to moulded foam inserts.

– Use an extraction system during work.

NOTICE

If separating cuts are made too deep, underlying reinforcement could be damaged.

– Only make separating cuts with body saw.

– Rewelding of reinforcements is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

– RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

– New part must be welded in within 90 minutes.

NOTICE

Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.

– After bonding, the vehicle must not be moved and left at room temperature (at least 15 °C) for 8 to 10 hours.

– During this time, the vehicle must be standing on a level surface.

Observe safety information → Rep. gr.00; Safety information

Only tools and workshop equipment authorised by Volkswagen AG may be used → Rep. gr.00; Tools.

Removing

– Apply duct tape to left and right roof members parallel to laser brazing seams.

– Roughly cut roof -1- out parallel to laser solder seams -2-.

– Separate original joint.

– Remove roof -1-.

– Remove remaining material -1-. Do not damage roof side member.

– Carefully remove remaining material of laser soldered seam from left and right roof side members.

– Completely remove adhesive residue.

– Sand bonding and welding surfaces down to bare metal, and clean them.

– Apply corrosion protection measures to left and right roof side members ⇒ Body, General paint information, Technical data, General information; Pre-treatment of bonded surfaces using 2-component epoxy filler when replacing laser-welded roofs.

– Grind bonding surface for 2-pack body adhesive -1- down to bare metal and clean.

– Implement corrosion protection measures on sand-through spots of bonding surface for 1-component assembly adhesive -2- General paint information – passenger vehicles; Repair group 00; General information; Pre-treatment of bonding surfaces when renewing laser-welded roofs.

– Apply glass/paint primer to bonding surface for 1-pack assembly adhesive -2-.

Installing

Replacement parts

♦ For allocation of 1-pack assembly adhesive, see → Electronic parts catalogue (ETKA)

♦ For allocation of 2-pack body adhesive, see → Electronic parts catalogue (ETKA)

♦ For allocation of adhesive sealant, see → Electronic parts catalogue (ETKA)

♦ For allocation of glass/paint primer, see → Electronic parts catalogue (ETKA)

♦ For allocation of felt strips, see → Electronic parts catalogue (ETKA).

Important

● Adhesive sealants must be applied quickly.

● It is essential to take account of the processing time (pot life) of adhesives.

Important

● New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.

– Grind welding surfaces and bonding surfaces on new part -1- down to bare metal and clean.

– Clean bonding surfaces -2- for 1-component assembly adhesive parallel to roof flange on left and right of new part -1-.

– Apply glass/paint primer to bonding surfaces -2- for 1-pack assembly adhesive.

– Cut approx. 2 mm off nozzle -B- to provide appropriate bead geometry.

– Apply 1-component assembly adhesive to roof cross member.

– Apply 1-component assembly adhesive to left and right roof side members according to dimensions -a- and -b-.

♦ Dimension -a- = 10 mm

♦ Dimension -b- = 14 mm

– Apply 1-component assembly adhesive to inside of new part -1- parallel to roof flange on left and right according to dimensions -a- and -b-.

♦ Dimension -a- = 14 mm

♦ Dimension -b- = 12 mm

– Cut off first step of static mixer -A- to achieve corresponding bead cross-section.

– Carefully operate double cartridge gun without static mixer until 2-component body adhesive is discharged uniformly from both chambers of connecting piece.

– Screw static mixer onto connecting piece.

– Discharge the first 100 mm of 2-component body adhesive onto a piece of cardboard and only then begin to apply the adhesive to the vehicle.

– Fill 2-component body adhesive in area of roof side members.

– Apply 2-component body adhesive to entire surface.

– Completely coat flanges -2- of new part -1- with 2-component body adhesive.

– Adapt new part -1- to fit, and fix it in position.

NOTICE

Risk of damage from overtensioning

– Do not overtighten tensioning straps.

– In areas shown, tension tensioning straps -2- transversely over roof to vary height of roof.

– Check dimension -a- on roof to roof side members.

♦ Dimension -a-= 6.0 mm ± 0.5 mm

– Fix position of new part -1- on front roof cross member and rear roof cross member using mole grips.

– If necessary, place felt strips underneath for compensation.

– Excessive 2-component body adhesive must be removed immediately.

– Excessive 2-component body adhesive must be removed immediately.

– Apply a thin coat of adhesive sealant onto seam between new part -1- and roof side member -5- to form a fine seam seal -2-.

– Adhesive bead -3- must seal off the interior.

Renewing roof side member

Renewing roof side member

WARNING

Gases/ vapours hazardous to health are generated when welding, soldering or cutting using tools which produce sparks in foam-treated areas.

– Do not weld, solder or cut closer than 15 mm to moulded foam inserts.

– Use an extraction system during work.

NOTICE

Do not damage underlying reinforcements.

Rewelding of reinforcement is not permitted due to safety reasons.

NOTICE

If welds are positioned too far on outside, strength could be impaired

– RP weld points must be placed as far as possible from outer edge of welding flange.

NOTICE

If adhesive is applied prematurely, bond could be impaired

– New part must be welded in within 90 minutes.

NOTICE

Bonding properties of adhesive may be impaired if adhesive components are not hardened sufficiently.

– After bonding, the vehicle must not be moved and left at room temperature (at least 15 °C) for 8 to 10 hours.

– During this time, the vehicle must be standing on a level surface.

Observe safety information → Rep. gr.00; Safety information

Only tools and workshop equipment authorised by Volkswagen AG may be used → Rep. gr.00; Tools.

Removal and installation are described for left side of vehicle as an example.

Removing

Roof removed (without glass panel) → Rep. gr.51; Renewing roof - vehicle without glass panel.

Roof removed (with glass panel) → Rep. gr.51; Renewing roof - vehicle with glass panel.

Permitted separating cuts on complete side panel → Rep. gr.53; Permitted separating cuts on side panel

– Make separating cuts -2- in a straight line, as shown.

– Separate original joint on roof side member -1-.

– Make separating cuts -2- in a straight line, as shown.

– Separate original joint.

– Remove roof side member -1-.

– Remove remaining material.

– Completely remove adhesive residue.

– Sand bonding and welding surfaces down to bare metal, and clean them.

Installing

Replacement parts

♦ For allocation of 2-pack body adhesive, see → Electronic parts catalogue (ETKA)

Important

● New parts must be adapted and attached with the vehicle standing on its wheels or straightening bracket set.

– Transfer separating cut -3- to new part -1-, and cut in a straight line.

– Sand bonding and welding surfaces down to bare metal, and clean them.

– Sand bonding surfaces on roof carrier reinforcements -2- down to bare metal.

– Apply 2-component body adhesive to entire surface.

– Adapt new part -1- to fit, and fix it in position.

– Check fit with attachments.

– Fix new part -1- in position in area of door apertures using mole grips.

– Weld in new part -1- (RP spot weld seam).

– Weld parting cuts (either MIG solder seam or SG stepped weld seam).

– Check fit with attachments.

– Weld in new part -1- (RP spot weld seam and SG plug weld seam).

– Weld parting cuts (either MIG solder seam or SG stepped weld seam).

– Install roof (without glass panel) → Rep. gr.51; Renewing roof - vehicle without glass panel.

– Install roof (with glass panel) → Rep. gr.51; Renewing roof - vehicle with glass panel.