General information on paint

Silicone Remover -LLS MAX 007-

~6min read

Designation:

  • Silicone Remover -LLS MAX 007-

Product description

The Silicone Remover -LLS MAX 007- is a water-based, reduced-solvent, high-active-content cleaning agent. The raw material base is specific solvent combinations.

Features:

  • Aerosol formulation specific to the product and suited to the application
  • constant atomizing pressure
  • Aerosol distribution
  • highest yield
  • professional paint finish
  • high cleaning and degreasing effect
  • enhances adhesion
  • highest yield
  • even distribution

Application information

Application

Recommended for:

  • Auxiliary product for panel painting and spot repair
  • ideally suited for use before subsequent painting with Aqua Plus waterborne basecoats

Suitable substrates:

  • primed and filled surfaces, metal, plastic, glass, old and factory paint finishes, painted and unpainted substrates

Features:

  • Paint surfaces are not attacked
  • removes all types of silicone, ideal cleaner for dirt and soot
  • removes cavity preservative or wax
  • removes resinous, dried-on grease residues, e.g. door hinges
  • removes oil and grease residues
  • ideal solvent for tar contamination
  • removes adhesive residues, e.g. stickers

Processing


Note

  • Wear appropriate personal protective equipment for occupational safety:
  • Respirator type: A2/P2
  • Protective gloves, e.g. made of latex or nitrile

Application method "Spray pass"

- Immediately before applying the next paint layer, apply a light spray pass and wipe dry at once with a clean, dry cloth.

- Do not let the silicone remover evaporate on the surface. Only work on small areas at a time.

- If heavily soiled, repeat the cleaning.

- Change cloths frequently. Do not use soiled cloths.


Note

If spraying is interrupted, make sure to spray the valve empty while holding the can upside down.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

Silicone Remover, long -LLS MAX 008-

Designation:

  • Silicone Remover, long -LLS MAX 008-

Product description

The Silicone Remover, long -LLS MAX 008- is a high-active-content cleaning agent with easy application and residue-free evaporation. The raw material base is specific solvent combinations.

Features:

  • Aerosol formulation specific to the product and suited to the application
  • constant atomizing pressure
  • Aerosol distribution
  • highest yield
  • professional paint finish
  • easy application
  • residue-free evaporation
  • removes silicone, grease, oil, wax, dirt, tar, soot
  • contains mild, non-aggressive solvents

Application information

Application

Recommended for:

  • Auxiliary product for panel painting and spot repair

Suitable substrates:

  • primed and filled surfaces, metal, plastic, glass, old and factory paint finishes, painted and unpainted substrates

Features:

  • Paint surfaces are not attacked
  • removes all types of silicone, ideal cleaner for dirt and soot
  • removes cavity preservative or wax
  • removes resinous, dried-on grease residues, e.g. door hinges
  • removes oil and grease residues
  • ideal solvent for tar contamination
  • removes adhesive residues, e.g. stickers

Processing


Note

  • Wear appropriate personal protective equipment for occupational safety:
  • Respirator type: A2/P2
  • Protective gloves, e.g. made of latex or nitrile

Application method "Spray pass"

- Apply a light spray pass and wipe off with a clean, dry non-woven cloth.

- Allow the cleaned surface to flash off well.

- If heavily soiled, repeat the cleaning.

- Change cloths frequently. Do not use soiled cloths.


Note

If spraying is interrupted, make sure to spray the valve empty while holding the can upside down.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

Blender

Designation:

  • Blender -LLS MAX 009-

Product description

The Blender -LLS MAX 009- is used in automotive spot painting to blend the paint transitions and edge zones between existing and new paint. The raw material base is specific resin and solvent combinations.

Features:

  • Aerosol formulation specific to the product and suited to the application
  • constant atomizing pressure
  • Aerosol distribution
  • professional paint finish
  • ideal for spot repair
  • simple, time-saving application
  • particularly suitable for blend-in work on 2-coat systems and 2K single-stage paints
  • very good softening ability
  • good polishability
  • produces seamless edge zones in the blend area

Application information

Application

Recommended for:

  • Spot repair and blend-in refinishing

Suitable substrates:

  • Apply immediately after spraying 2K Clear Coat -LLS MAX 210- or 2K topcoat onto the transition areas of the blend area.
  • The substrate in the overspray transition zone should be thoroughly scuffed with a sanding pad (P2000-P4000).

Preparation:

  • No special work is required immediately before applying the blender.

Processing


Note

  • Wear appropriate personal protective equipment for occupational safety:
  • Respirator type: A2/P2
  • Protective gloves, e.g. made of latex or nitrile

Application method "Spray pass"

- Spray in several light passes onto the overspray edge zone of the 2K clear coat or 2K topcoat until a uniform transition is achieved.

- No flash-off time is required for the 2K clear coat or 2K topcoat.


Note

If spraying is interrupted, make sure to spray the valve empty while holding the can upside down.


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 36 months from production date. Use by the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

Adhesion Promoter

Designation:

  • Adhesion Promoter -LLS MAX 015-, plastic

Product description

The Adhesion Promoter -LLS MAX 015- is a universal one-component adhesion promoter for all common exterior plastic vehicle parts.

Features:

  • easy application
  • good adhesion properties
  • high flexibility

Application information

Substrate

Suitable substrates:

  • All common exterior plastic vehicle parts (PP, EPDM, ABS, PC, PPO, PA, R-TPU, PBTP, PVC, PUR, flexible PUR foam, UP-GF).

Pretreatment of substrates:

The substrate must be free of release agents.

Before cleaning, temper plastic parts for 60 minutes at +60 °C so that the release agents "sweat out".

- Clean with plastic cleaner, antistatic -LVM 001 001 A2- or with the milder silicone remover, long -LVM 020 100 A5-.


Note

  • The effort required for cleaning depends on the type and amount of release agent used. To support cleaning, we recommend using a sanding pad.
  • Allow the thinner to flash off thoroughly (e.g. by air drying overnight at room temperature or 30-40 minutes at +60 °C).
VW UP. Allgemeine Informationen Lack

- Before priming, clean again lightly with plastic cleaner, antistatic -LVM 001 001 A2- or silicone remover, long -LVM 020 100 A5- (antistatic effect).

VW UP. Allgemeine Informationen Lack

Processing

Application:

- Shake the can thoroughly for at least 2 minutes.

VW UP. Allgemeine Informationen Lack

Application method "Spray pass"

- Apply 1 full spray pass (1-2 µm).

Spray distance:

- Maintain a spray distance of 20-25 cm.

VW UP. Allgemeine Informationen Lack

Flash-off time: 10-15 minutes at +20 °C room temperature


Note

  • If spraying is interrupted, spray the valve empty upside down to prevent the nozzle from clogging.
  • Sanded-through spots no larger than Ø 5.0 cm can be refinished directly with topcoat using Adhesion Promoter -LLS MAX 015-.

Further processing

Use with fillers:

  • elasticized 2K HS filler (for elasticizing, see the technical application information of the respective filler)

Can be overcoated with:

  • 2K HS topcoat
  • Waterborne basecoat and 2K HS clearcoat


Caution!

Wear suitable personal protective equipment in accordance with occupational safety regulations.

Observe the safety data sheets and the warnings on the spray can label.

Shake again briefly before each spray pass.

Dispose of empty spray cans as recyclable material.

Characteristics

VW UP. Allgemeine Informationen Lack


Storage

The guaranteed storage stability is 60 months from the date of production. Usable until the date stated on the label at the latest when stored in sealed original containers at +20 ºC.

VW UP. Allgemeine Informationen Lack

Storage conditions

Required storage temperature is +20 to +25 ºC (must not fall below +5 ºC).

VW UP. Allgemeine Informationen Lack