ECU Terminals
ECU TERMINALS
CHECK INSTRUMENT PANEL JUNCTION BLOCK ASSEMBLY AND MAIN BODY ECU (MULTIPLEX NETWORK BODY ECU)
*A |
Main Body ECU (Multiplex Network Body ECU) with 2 connectors |
- |
- |
*1 |
Main body ECU (multiplex network body ECU) |
- |
- |
*a |
2 connectors |
- |
- |
*A |
Main Body ECU (Multiplex Network Body ECU) with 1 connector |
- |
- |
*1 |
Main body ECU (multiplex network body ECU) |
- |
- |
*a |
1 connector |
- |
- |
(a) Disconnect the connectors from the instrument panel junction block assembly and the main body ECU (multiplex network body ECU).
(b) Measure the voltage of the connector on the wire harness side according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
3F-1 - Body Ground |
W - Body Ground |
Battery power supply |
Always |
11 à 14 V |
3K-1 - Body Ground |
B-R - Body Ground |
Battery power supply |
Always |
11 à 14 V |
If the result is not as specified, there may be a malfunction in the wire harness.
(c) Measure the resistance of the connector on the wire harness side according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
3D-3 - Body Ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
If the result is not as specified, there may be a malfunction in the wire harness.
(d) Reconnect the connectors to the instrument panel junction block assembly and the main body ECU (multiplex network body ECU).
(e) Measure the voltage and check the pulses according to the value(s) in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
3F-31 - Body Ground |
G - Body ground |
LH H-LP Relay Control Output |
Ignition Switch in OFF position |
11 à 14 V |
Ignition Switch in ON position |
Below 1 V |
|||
F15-1 (DIM) - Body Ground |
Y - Body Ground |
RH H-LP Relay Control Output |
Ignition Switch in OFF position |
11 à 14 V |
Ignition Switch in ON position |
Below 1 V |
|||
F15-8 (A) - Body Ground |
W - Body Ground |
Light Control Switch AUTO Position Signal Input |
Light Control Switch in AUTO position |
Below 1 V |
Light Control Switch is not in AUTO position |
Pulse generation |
|||
F15-12 (HEAD) - Body Ground |
L - Body ground |
Light Control Switch HEAD Position Input |
Light Control Switch in HEAD position |
Below 1 V |
Light Control Switch is not in HEAD position |
Pulse generation |
|||
F15-17 (AHBI) - Body Ground |
Y - Body Ground |
Auto High Beam Switch Signal Input Voltage |
Ignition switch ON, auto high beam switch OFF |
11 à 14 V |
Ignition switch ON, auto high beam switch ON |
Below 1 V |
|||
F15-19 (CLTB) - F15-21 (CLTE) |
G - V |
Auto Light Control Sensor Power Supply Output |
Ignition Switch in OFF position |
Below 1 V |
Ignition Switch in ON position |
11 à 14 V |
|||
F15-20 (CLTS) - Body Ground |
BE - Body ground |
Automatic Light Control Sensor Signal Input |
Ignition Switch in OFF position |
Below 1 V |
Automatic headlight control system |
Communication Waveform Generation (see waveform 1) |
|||
F15-20 (CLTS) - Body Ground |
BE - Body ground |
Automatic light control sensor signal input |
Ignition Switch in OFF position |
Below 1 V |
Automatic light control system operation |
Communication waveform generation (See waveform 1) |
|||
F15-24 (HU) - Body ground |
GR - Body ground |
High beam/low beam switch HIGH position signal input |
Dimmer switch in HIGH position |
Below 1 V |
High beam/low beam switch not in HIGH position |
Pulse generation |
- *1: If the light switch does not have an OFF position, set the light switch to "Auto" with the low beams off. If the low beams are on, direct a fluorescent light or another light source at the light sensor to switch to daytime mode.
If the result does not conform to the specifications, there may be a malfunction in the main body ECU (multiplex network body ECU) or the instrument panel junction block assembly.
(1) Waveform 1
Item | Content |
|---|---|
Oscilloscope Setting |
2 V/DIV., 10 ms/DIV. |
HINT:
The communication waveform changes depending on the ambient brightness.
CHECK LH HEADLIGHT ECU SUB-ASSEMBLY (for LED headlights)
Click here
![]()
CHECK RH HEADLIGHT ECU SUB-ASSEMBLY (for LED headlights)
Click here
![]()
CHECK FRONT CAMERA SENSOR
Click here![]()