Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.
HINT:
The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / Main Body / Data List.
(e) Read the Data List by following the instructions on the Techstream.
Body Electrical > Main Body > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Auto High Beam Main Switch |
Auto High Beam Switch Signal |
ON or OFF |
ON: Auto high beam switch pressed OFF: Auto high beam switch released |
- |
Dimmer SW |
High beam/low beam switch HIGH position signal |
ON or OFF |
ON: High beam/low beam switch in HIGH or HIGH FLASH position OFF: High beam/low beam switch in LOW position |
- |
Auto Light SW |
Light control switch AUTO position signal |
ON or OFF |
ON: Light control switch in AUTO position OFF: Light control switch is not in AUTO position |
- |
Head Light SW (Head) |
Light control switch HEAD position signal |
ON or OFF |
ON: Light control switch in HEAD position OFF: Light control switch is not in HEAD position |
- |
Light Sensor Illuminance |
Light control sensor illuminance |
0 to 8,191 lx |
The value is output according to ambient light levels |
- |
Auto H Beam STS0 |
Current Auto High Beam Sensor Status |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
Undetec: Not detected CAM NA: Camera detection malfunction*1 No sens: No sensing Hlight: Headlights of oncoming vehicles are on Taillgt: Tail lights of vehicles ahead are on Speed: Vehicle speed Daytime: Daytime condition Village: Urban area Malfunc: System delay |
Auto H Beam STS1 |
Auto high beam sensor status past 1 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS2 |
Auto high beam sensor status past 2 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS3 |
Auto high beam sensor status past 3 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS4 |
Auto high beam sensor status past 4 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS5 |
Auto high beam sensor status past 5 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS6 |
Auto high beam sensor status past 6 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
Auto H Beam STS7 |
Auto high beam sensor status past 7 |
Undetec, CAM NA, No sens, Hlight, Taillgt, Speed, Daytime, Village, Malfunc |
The status can be displayed. |
*2 |
The Number of DTC |
Number of DTCs |
0 à 255 |
The status can be displayed. |
- |
- *1: If CAM NA is displayed, the front camera sensor may no longer operate due to high temperature.
- *2: Although the item is displayed on the Techstream, it is not applicable to the vehicle.