ECU Terminals
ECU TERMINALS
CHECK MILLIMETER WAVE RADAR SENSOR
(a) Measure the voltage and resistance according to the value(s) shown in the table below.
HINT:
If the result is not as specified, there may be a malfunction in the wire harness.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A2-8 (IGB) - A2-1 (SGND) |
B - W-B |
Power source |
Ignition Switch in ON position |
11 à 14 V |
A2-1 (SGND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(b) Check the pulses according to the value(s) shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
A2-3 (CA2H) - A2-1 (SGND) |
G - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (See waveform 1) |
A2-2 (CA2L) - A2-1 (SGND) |
GR - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (see waveform 2) |
A2-5 (CA1P) - A2-1 (SGND) |
G - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (See waveform 1) |
A2-6 (CA1N) - A2-1 (SGND) |
R - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (see waveform 2) |
(c) WAVEFORM 1
(1) CAN communication signal
Item | Content |
|---|---|
Terminal description |
Between A2-3 (CA2H) and A2-1 (SGND) Between A2-5 (CA1P) and A2-1 (SGND) |
Tester operating range |
1 V/DIV., 10 µs./DIV. |
Condition |
Ignition Switch in ON position |
HINT:
The waveform varies depending on the CAN communication signal.
(d) WAVEFORM 2
(1) CAN communication signal
Item | Content |
|---|---|
Terminal description |
Between A2-2 (CA2L) and A2-1 (SGND) Between A2-6 (CA1N) and A2-1 (SGND) |
Tester operating range |
1 V/DIV., 10 µs./DIV. |
Condition |
Ignition Switch in ON position |
HINT:
The waveform varies depending on the CAN communication signal.
CHECK FRONT CAMERA SENSOR
(a) Measure the voltage and resistance according to the value(s) shown in the table below.
HINT:
If the result is not as specified, there may be a malfunction in the wire harness.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
R5-8 (BZ) - R5-10 (GND) |
B - W-B |
Pre-Collision System Urban Buzzer |
Ignition switch ON, city Pre-Collision System buzzer does not operate |
11 à 14 V |
Ignition switch ON, city Pre-Collision System buzzer operates |
0 à 1,5 V |
|||
R5-3 (LKSW) - R5-10 (GND) |
R - W-B |
Pre-Collision System disable switch assembly |
Pre-Collision System disable switch assembly pressed |
Below 1 Ω |
Pre-Collision System disable switch assembly not pressed |
100 kΩ minimum |
|||
R5-7 (IGB) - R5-10 (GND) |
B - W-B |
Power source |
Ignition Switch in ON position |
11 à 14 V |
Ignition Switch in OFF position |
Below 1 V |
|||
R5-10 (GND) - Body ground |
W-B - Body ground |
Ground |
Always |
Below 1 Ω |
(b) Check the pulses according to the value(s) shown in the table below.
Terminal No. (Symbol) | Wire Color | Terminal Description | Condition | Specified Condition |
|---|---|---|---|---|
R5-5 (CA1P) - R5-10 (GND) |
R - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (See waveform 1) |
R5-6 (CANH) - R5-10 (GND) |
G - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (See waveform 1) |
R5-11 (CA1N) - R5-10 (GND) |
GR - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (see waveform 2) |
R5-12 (CANL) - R5-10 (GND) |
R - W-B |
CAN communication signal |
Ignition Switch in ON position |
Pulse generation (see waveform 2) |
(c) WAVEFORM 1
(1) CAN communication signal
Item | Content |
|---|---|
Terminal description |
Between R5-5 (CA1P) and R5-10 (GND) Between R5-6 (CANH) and R5-10 (GND) |
Tester operating range |
1 V/DIV., 10 µs./DIV. |
Condition |
Ignition Switch in ON position |
HINT:
The waveform varies depending on the CAN communication signal.
(d) WAVEFORM 2
(1) CAN communication signal
Item | Content |
|---|---|
Terminal description |
Between R5-11 (CA1N) and R5-10 (GND) Between R5-12 (CANL) and R5-10 (GND) |
Tester operating range |
1 V/DIV., 10 µs./DIV. |
Condition |
Ignition Switch in ON position |
HINT:
The waveform varies depending on the CAN communication signal.
