Preventive Action

Precautions

~5min read

PRECAUTION

IGNITION SWITCH TERMS

(a) The type of ignition switch used varies depending on vehicle specifications. The terms listed in the table below are used in this section.

Term

Ignition Switch (Position)

Engine Switch (Condition)

Ignition Switch in OFF position

LOCK

OFF (Locked)

Ignition Switch in ACC position

ACC

ON (ACC)

Ignition Switch in ON position

ON

ON (IG)

Starting the engine

START

ON (Starting)

PRECAUTIONS FOR DISCONNECTING THE CABLE FROM THE NEGATIVE BATTERY TERMINAL

NOTICE:

  • When disconnecting the negative (-) battery terminal cable, some systems must be initialized after the cable is reconnected.

    Click here

  • If the battery is discharged and recharged, or if the cable has been disconnected and reconnected to the negative (-) battery terminal, perform zero point calibration of the steering angle sensor.

    Click here

PRECAUTIONS BEFORE SERVICING

(a) Be sure to turn the pre-collision system OFF under the following conditions, as it may activate unexpectedly or fail to function when needed.

  • When the vehicle is being towed
  • When towing another vehicle
  • When transporting the vehicle by truck, ship, train or other similar means
  • When the vehicle is lifted on a hoist with the engine running and the tires free to turn
  • When checking the vehicle using a roller-type test bench, such as a chassis dynamometer or speedometer tester, or when using a wheel balancer on the vehicle
  • When a severe impact is applied to the front bumper or front grille as a result of an accident or other causes
  • If the vehicle cannot be driven stably, for example if it has been involved in an accident or is not operating properly
  • When the vehicle is driven sportily or off-road
  • When the tires are not inflated properly
  • When the tires are severely worn
  • When tires of a size other than specified are installed
  • If snow chains are installed
  • When using a compact spare tire or a tire repair kit
  • If the suspension has been modified
  • If the front of the vehicle is raised or lowered, for example when carrying heavy luggage

PRECAUTIONS FOR TROUBLESHOOTING

(a) If a malfunction occurs due to a terminal contact problem or improper installation of a part, removing and correctly reinstalling the affected part may restore normal system operation. However, this return to normal may be temporary.

(b) Before disconnecting connectors or removing/installing parts, identify the malfunctioning area by checking the vehicle operating conditions and recording them at the time of the malfunction (DTC output, etc.).

(c) Be sure to also check the DTCs for other systems. The pre-collision system may be affected by malfunctions in other systems.

PRECAUTIONS FOR HANDLING

(a) When removing and installing ECUs, sensors, switches or other parts related to the pre-collision system, observe the following:

  • Make sure the ignition switch is in the OFF position, unless otherwise specified in the procedure.
  • After removal and installation, check for DTCs and confirm that a normal system code is output.

PRECAUTIONS FOR REPLACEMENT

(a) MILLIMETER WAVE RADAR SENSOR ASSEMBLY:

(1) When replacing the millimeter wave radar sensor assembly, replace it with a new one.

(2) If the millimeter wave radar sensor assembly has been replaced with a new one, be sure to perform beam axis adjustment for the front.

Click here

(b) FRONT MONITORING CAMERA:

(1) If the front monitoring camera has been replaced with a new one, or the windshield glass has been removed or installed, front area recognition axis adjustment is required. If the system is turned ON without performing front area recognition axis adjustment, DTC C1AA9 will be stored.

Click here

(c) WINDSHIELD GLASS:

(1) When replacing the windshield glass on a vehicle equipped with a front area recognition camera, be sure to use a genuine Toyota part. If a non-genuine part is used, the front area recognition camera may not be installed due to lack of support, or the pre-collision system may not function properly due to differences in transmittance or the black ceramic edge.

(2) Do not attach stickers, including transparent stickers, or other items to the outer surface of the windshield glass in the area in front of the forward recognition camera.