Preventive Action

Yaw rate sensor (C1A46)

~5min read

DESCRIPTION

The millimeter wave radar sensor assembly receives yaw and acceleration sensor (airbag sensor assembly) signals from the airbag sensor assembly and the skid control ECU (brake actuator assembly) via CAN communication. If the millimeter wave radar sensor assembly receives yaw and acceleration sensor malfunction signals from the airbag sensor assembly or the skid control ECU (brake actuator assembly), DTC C1A46 is stored.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

C1A46

Yaw rate sensor

One of the following conditions is met

  • While the vehicle is driving at a speed of 5 km/h or more, the millimeter wave radar sensor assembly receives yaw and acceleration sensor (airbag sensor assembly) malfunction signals from the yaw and acceleration sensor (airbag sensor assembly) for approximately 10 seconds.
  • While the vehicle is driving at a speed of 5 km/h or more, the millimeter wave radar sensor assembly receives malfunction signals from the skid control ECU (brake actuator assembly) via the yaw and acceleration sensor (airbag sensor assembly) for approximately 1 second from the zero point.
  • Vehicle Stability Control System
  • Yaw rate and acceleration sensor (airbag sensor assembly)
  • Skid control ECU (brake actuator assembly)
  • Millimeter wave radar sensor assembly
DTC detection conditions:

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

When the vehicle is driving at a speed of 5 km/h or more.

○

○

Malfunction Status

The millimeter wave radar sensor assembly receives yaw and acceleration sensor malfunction signals from the yaw and acceleration sensor (airbag sensor assembly).

○

-

The millimeter wave radar sensor assembly receives malfunction signals from the skid control ECU (brake actuator assembly) via the yaw and acceleration sensor (airbag sensor assembly) from the zero point.

-

○

Detection Duration

10 seconds

1 second

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the millimeter wave radar sensor assembly, always replace it with a new one.
  • When the millimeter wave radar sensor assembly is replaced with a new one, the radar sensor beam axis must be adjusted.

    Click here

  • The Pre-Collision System uses the CAN communication system. First, make sure there are no malfunctions in the CAN communication system. Refer to How to Use Troubleshooting.

    Click here

PROCEDURE

  1. CHECK DTCs (VEHICLE STABILITY CONTROL SYSTEM)

HINT:

The Pre-Collision Safety System DTC C1A46 may be stored due to a malfunction in the VSC system. Therefore, check and perform troubleshooting of the VSC system DTCs first.

(a) Check the DTCs.

Click here

Chassis > ABS/VSC/TRAC/EPB > Trouble Codes

Result:

Result

Proceed to

VSC-related DTCs are not output

A

VSC-related DTCs are output

B

B

GO TO VEHICLE STABILITY CONTROL SYSTEM

A
  1. READ DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system is unable to detect malfunctions.

(c) Check the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Trouble Codes

Result:

Result

Proceed to

DTC C1A46 is not output

A

DTC C1A46 is output

B

A

USE SIMULATION METHOD TO CHECK

B
  1. REPLACE MILLIMETER WAVE RADAR SENSOR ASSEMBLY

(a) Replace the millimeter wave radar sensor assembly.

Click here

(b) Adjust the millimeter wave radar sensor assembly.

Click here

NEXT
  1. READ DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system is unable to detect malfunctions.

(c) Check the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Trouble Codes

Result:

Result

Proceed to

DTC C1A46 is not output

A

DTC C1A46 is output

B

A

END (MILLIMETER WAVE RADAR SENSOR ASSY WAS MALFUNCTIONING)

B
  1. REPLACE YAW AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY)

(a) Replace the yaw and acceleration sensor (airbag sensor assembly).

Click here

NEXT
  1. READ DTCs (PRE-COLLISION SYSTEM)

(a) Clear the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Clear DTCs

(b) Make sure the DTC detection conditions are met.

HINT:

If the detection conditions are not met, the system is unable to detect malfunctions.

(c) Check the DTCs.

Click here

Body Electrical > Pre-Collision 2 > Trouble Codes

Result:

Result

Proceed to

DTC C1A46 is not output

A

DTC C1A46 is output

B

A

END (YAW AND ACCELERATION SENSOR (AIRBAG SENSOR ASSEMBLY) WAS FAULTY)

B

REPLACE SKID CONTROL ECU (BRAKE ACTUATOR ASSEMBLY)