Data List / Active Test
DATA LIST / ACTIVE TEST
DATA LIST
HINT:
The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.
NOTICE:
In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / Pre-Collision 2 / Data List.
(e) Read the Data List by following the instructions on the Techstream.
Body Electrical > Pre-Collision 2 > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Turn Light RH |
Turn signal switch position (RH) |
ON or OFF |
ON: Right turn signal switch in ON position OFF: Right turn signal switch in OFF position |
- |
Turn Light LH |
Turn signal switch position (LH) |
ON or OFF |
ON: Left turn signal switch in ON position OFF: Left turn signal switch in OFF position |
- |
PCS OFF Switch |
Pre-collision safety system on/off switch status |
ON or OFF |
ON: Pre-collision safety system switch in ON position OFF: Pre-collision safety system switch in OFF position |
- |
PCS Indicator |
Request signal for "Pre-Collision System Malfunction Visit Your Dealer" message display |
ON or OFF |
ON: "Pre-Collision System Malfunction Visit Your Dealer" message display requested OFF: "Pre-Collision System Malfunction Visit Your Dealer" message display not requested |
- |
PCS Disabled Indicator |
Request signal for "Pre-Collision System Unavailable" message display |
ON or OFF |
ON: "Pre-Collision System Unavailable" message display requested OFF: "Pre-Collision System Unavailable" message display not requested |
- |
Pre-Collision Safety Warning Buzzer |
Pre-collision safety system warning buzzer |
Valid or Inval |
Valid: Pre-collision safety system warning buzzer can operate Inval: Pre-collision safety system warning buzzer cannot operate |
- |
Pre-Collision Brake |
Pre-collision braking function |
Valid or Inval |
Valid: Pre-collision braking can operate Inval: Pre-collision braking cannot operate |
- |
PBA Start |
Pre-collision brake assist activation signal |
OFF, Standby, Assist Lv1 or Lv2 |
OFF: Pre-collision brake assist inoperative Standby: Brake pedal released while pre-collision brake assist is operating Assist Lv1: Brake pedal depressed while pre-collision brake assist is operating Assist Lv2: Brake pedal firmly depressed while pre-collision brake assist is operating |
The signal state changes when pre-collision brake assist is activated before a collision (pre-collision braking will only activate in situations where the driver depresses the brake pedal) |
Brake Assist Standby |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
Pre-Collision Brake Control |
Pre-collision braking operating status |
ON or OFF |
ON: Pre-collision braking operating OFF: Pre-collision braking not operating |
- |
AVS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
VGRS Start |
- |
- |
- |
This item is displayed on the Techstream but is not used. |
PBA Control |
Pre-collision brake assist operating status |
Valid or Invalid |
Valid: Pre-collision brake assist control operation is possible Invalid: Pre-collision brake assist control operation is not possible |
- |
Pre-Collision Safety Brake Indicator |
Pre-collision system alarm warning message status |
ON or OFF |
ON: Displayed OFF: Not displayed |
The "BRAKE!" message is displayed |
PCS Collision Alarm Buzzer |
Pre-collision urban safety buzzer status |
ON or OFF |
ON: Pre-collision urban safety buzzer sounds OFF: Pre-collision urban safety buzzer does not sound |
- |
Front Radar-Dirt History |
Millimeter wave radar sensor assembly dirt history |
ON or OFF |
ON: Excessive dirt history OFF: No excessive dirt history |
- |
Front Radar-Environment Hist |
Millimeter wave radar sensor assembly environment signal |
Good or Bad |
Good: Millimeter wave radar sensor assembly environment is good Bad: Millimeter wave radar sensor assembly environment is bad |
- |
Front Radar-Temperature Malfunction History |
Millimeter wave radar sensor assembly abnormal temperature history |
ON or OFF |
ON: Abnormal temperature history OFF: No abnormal temperature history |
- |
Front Radar-Low Voltage History |
Millimeter-wave radar sensor assembly low voltage history |
ON or OFF |
ON: Low voltage history present OFF: No low voltage history |
If the engine starts at least 1 second after the ignition switch has been turned to ON (IG), this item may switch to ON |
Front Recognition Camera-Blockage History |
Forward recognition camera blockage history |
ON or OFF |
ON: Blockage history OFF: No blockage history |
- |
Front Recognition Camera-Malfunction History |
The front recognition camera system malfunction history is not available |
ON or OFF |
ON: History not available OFF: History not available |
- |
Destination Variation No |
Destination country for millimeter wave radar sensor assembly |
0 or Not Available |
Not available: |
- |
Control Mode |
ECU control mode status |
Normal or Check Mode |
Normal: Normal operation Check Mode: Operating in check mode |
- |
PCS Operation State Retention Setting |
PCS operating status maintenance customization setting |
ON or OFF |
ON: Customization setting enabled OFF: Customization setting disabled |
- |
PCS Alarm Activation Distance Retention Setting 1 |
PCS alarm activation distance maintenance customization setting, parameter 1 |
ON or OFF |
ON: Customization setting enabled OFF: Customization setting disabled |
- |
PCS Alarm Activation Distance Retention Setting 2 |
PCS alarm activation distance maintenance customization setting, parameter 2 |
ON or OFF |
ON: Customization setting enabled OFF: Customization setting disabled |
- |
PCS Alarm Activation Distance Retention Setting 3 |
PCS alarm activation distance maintenance customization setting, parameter 3 |
ON or OFF |
ON: Customization setting enabled OFF: Customization setting disabled |
- |
The Number of DTCs |
Number of past diagnostic codes |
minimum: 0, maximum: 255 |
Display number of DTCs |
- |
(f) Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Data List.
(g) Read the Data List by following the Techstream instructions.
Chassis > ABS/VSC/TRAC/EPB > Data ListTester display | Item | Range | Normal Condition | Diagnostic Note |
|---|---|---|---|---|
Stop Light Relay Output |
Stop light switch assembly output |
ON or OFF |
ON: Stop light switch assembly output in ON position (stop lights ON) OFF: Stop light switch assembly output in OFF position (stop lights OFF) |
- |
ACTIVE TEST
HINT:
Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.
(a) Connect the Techstream to the DLC3.
(b) Turn the ignition switch to ON.
(c) Turn on the Techstream.
(d) Select the following menus: Body Electrical / Pre-Collision 2 / Active Test.
(e) Perform the Active Test by following the Techstream instructions.
Body Electrical > Pre-Collision 2 > Active TestTester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
PCS Collision Alarm Buzzer |
Pre-Collision System Urban Buzzer |
ON / OFF |
The test can be performed when the ignition switch is ON. Vehicle operating conditions: Vehicle stopped |
(f) Select the following menus: Chassis / ABS/VSC/TRAC/EPB / Active Test.
(g) Perform the Active Test by following the instructions on the Techstream.
Chassis > ABS/VSC/TRAC/EPB > Active TestTester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Stop Light Relay |
Stop light switch assembly |
Stop light switch assembly ON/OFF |
Stop lights illuminate Vehicle operating conditions: Vehicle stopped |
(h) Select the following menus: Body Electrical / Combination Meter / Active Test.
(i) Perform the Active Test by following the Techstream instructions.
Body Electrical > Combination Meter > Active TestTester display | Item | Control Range | Diagnostic Note |
|---|---|---|---|
Precrash Indicator |
PCS light |
ON / OFF |
- |