Heater / Air Conditioning

ECU Terminals

~16min read

ECU TERMINALS

AIR CONDITIONING AMPLIFIER ASSEMBLY

HINT:

Check the rear of the connector while it is connected to the air conditioning amplifier assembly.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

F72-1 (B) - Body ground

V - Body ground

Power Source (Backup)

Always

11 à 14 V

F72-3 (LIN1) - F72-29 (GND)

L - W-B

LIN Communication Signal (Air Conditioning Control Assembly)

Ignition Switch in ON position

Pulse generation

(See waveform 1)

F72-5 (IG+) - Body ground

B - Body ground

Power supply (IG)

Ignition Switch in ON position

11 à 14 V

Ignition Switch in OFF position

Below 1 V

F72-9 (CANH) - F72-10 (CANL)

P - SB

CAN Communication

CAN Communication is Performed

Pulse generation

F72-15 (SOL-) - F72-29 (GND)

L - W-B

Compressor Solenoid Valve Operation

  • Engine is running
  • Blower Switch: Lo
  • A/C Switch: ON

Pulse generation

(see waveform 2)

F72-17 (NAIN) - F72-29 (GND)*1

W - W-B

Ion Generator Assembly Status Input

  • Ignition Switch in ON position
  • Blower Switch: OFF

3,5 à 5 V

  • Ignition Switch in ON position
  • Blower Switch: Lo

Below 2 V

F72-19 (PTC1) - F72-29 (GND)*2

L - W-B

Power for Line PTC1 Heater Relay

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: 25 °C maximum
  • Engine coolant temperature: 75 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: Lo

Below 1 V

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: 25 °C maximum
  • Engine coolant temperature: 75 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: OFF

11 à 14 V

F72-20 (PTC3) - F72-29 (GND)*2

BR - W-B

Power for Line PTC3 Heater Relay

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: -7°C (19°F) maximum
  • Engine coolant temperature: 65 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: Lo

Below 1 V

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: -7°C (19°F) maximum
  • Engine coolant temperature: 65 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: OFF

11 à 14 V

F72-29 (GND) - Body ground

W-B - Body ground

Ground for Main Power Supply

Always

Below 1 V

F72-30 (TR) - F72-31 (SG-1)

B - LG

Cooler Thermistor (Room Temperature Sensor)

  • Ignition Switch in ON position
  • Room Temperature: 25 °C

1,8 à 1,6 V

  • Ignition Switch in ON position
  • Room Temperature: 40 °C

1,0 à 0,8 V

F72-31 (SG-1) - Body Ground

LG - Body ground

Ground for Cooler Thermistor (Room Temperature Sensor)

Always

Below 1 V

F72-32 (SG-2) - Body Ground

G - Body ground

Ground for Air Conditioning Pressure Sensor

Always

Below 1 V

F72-33 (PRE) - F72-32 (SG-2)

V - G

Input from Refrigerant Gas Sensor

  • Ignition Switch in ON position
  • Air Conditioning System ON
  • Refrigerant Pressure: Abnormal Pressure (Higher than 3,025 kPa (30.8 kgf/cm2, 439 psi))

4.61 V Minimum

  • Ignition Switch in ON position
  • Air Conditioning System ON
  • Refrigerant Pressure: Abnormal Pressure (Lower than 176 kPa (1.8 kgf/cm2, 26 psi))

Below 0.74 V

  • Ignition Switch in ON position
  • Air Conditioning System ON
  • Refrigerant pressure: Normal pressure (less than 3,025 kPa (30.8 kgf/cm2, 439 psi) and more than 176 kPa (1.8 kgf/cm2, 26 psi))

0,74 à 4,61 V

F72-34 (S5-3) - F72-32 (SG-2)

GR - G

Power Source for Air Conditioning Pressure Sensor

Ignition Switch in ON position

4,75 à 5,25 V

Ignition Switch in OFF position

Below 1 V

F72-37 (NANO) - F72-29 (GND)*1

R - W-B

Output for Ion Generator Assembly

  • Ignition Switch in ON position
  • Blower Switch: Lo

3,5 à 5 V

  • Ignition Switch in ON position
  • Blower Switch: Lo

Below 2 V

F72-39 (PTC2) - F72-29 (GND)*2

V - W-B

Power for Line PTC2 Heater Relay

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: 16 °C maximum
  • Engine coolant temperature: 70 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: Lo

Below 1 V

  • Ignition Switch in ON position
  • ECO mode: OFF
  • Temperature setting: MAX HOT
  • Ambient temperature: 16 °C maximum
  • Engine coolant temperature: 70 °C maximum
  • Illumination control switch in OFF position
  • Blower Switch: OFF

11 à 14 V

F7A-2 (B2AI) - Body Ground

-

Output for motor drive to switch between B2 input/output

  • Ignition Switch in ON position
  • No. 1 Blower Damper Servo Assembly (outside air/recirculation air) operating

Pulse generation

(See waveform 3)

F7A-3 (A2AI) - Body Ground

-

Output for motor drive to switch between A2 input/output

  • Ignition Switch in ON position
  • No. 1 Blower Damper Servo Assembly (outside air/recirculation air) operating

Pulse generation

(See waveform 3)

F7A-4 (A2AO) - Body Ground

-

Power to drive motor in A2 switching mode

  • Ignition Switch in ON position
  • No. 2 Air Conditioning Radiator Damper Servo Assembly (mode switching) operating

Pulse generation

(see waveform 4)

F7A-6 (B2AO) - Body Ground

-

Power to drive motor in B2 switching mode

  • Ignition Switch in ON position
  • No. 2 Air Conditioning Radiator Damper Servo Assembly (mode switching) operating

Pulse generation

(see waveform 4)

F7A-8 (B1AO) - Body Ground

-

Power to drive motor in B1 switching mode

  • Ignition Switch in ON position
  • No. 2 Air Conditioning Radiator Damper Servo Assembly (mode switching) operating

Pulse generation

(see waveform 4)

F7A-9 (A1AI) - Body Ground

-

Output for motor drive to switch between A1 input/output

  • Ignition Switch in ON position
  • No. 1 Blower Damper Servo Assembly (outside air/recirculation air) operating

Pulse generation

(See waveform 3)

F7A-10 (B1AI) - Body Ground

-

Output to drive motor to switch between IN/OUT B1

  • Ignition Switch in ON position
  • No. 1 Blower Damper Servo Assembly (outside air/recirculation air) operating

Pulse generation

(See waveform 3)

F7A-12 (BLU) - Body Ground

-

Power supply to air mix motor in upper left layer

Ignition Switch in ON position

11 à 14 V

F7A-13 (BAI) - Body Ground

-

Power supply to motor to switch between IN/OUT

Ignition Switch in ON position

11 à 14 V

F7A-14 (BLL) - Body Ground

-

Power supply to air mix motor in lower left layer

Ignition Switch in ON position

11 à 14 V

F7A-16 (A1AO) - Body Ground

-

Power to switch motor to A1 switching mode

  • Ignition Switch in ON position
  • No. 2 Air Conditioning Radiator Damper Servo Assembly (mode switching) operating

Pulse generation

(see waveform 4)

F7A-18 (B2LL) - Body Ground

-

Output to drive air mix motor in lower left layer B2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower driver side air mix)

Pulse generation

(see waveform 5)

F7A-19 (B1LU) - Body Ground

-

Output to drive air mix motor in upper left layer B1

  • Ignition Switch in ON position
  • No. 1 A/C Radiator Damper Servo Sub-assembly (upper driver side air mix) operation

Pulse generation

(see waveform 6)

F7A-20 (A1LL) - Body Ground

-

Output to drive air mix motor in lower left layer A1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower driver side air mix)

Pulse generation

(see waveform 5)

F7A-22 (B1RU) - Body Ground

-

Output to drive air mix motor in upper right layer B1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (upper front passenger side air mix)

Pulse generation

(see waveform 8)

F7A-23 (A2RL) - Body Ground

-

Output to drive air mix motor in lower right layer A2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower front passenger side air mix)

Pulse generation

(see waveform 7)

F7A-24 (A1RU) - Body Ground

-

Output to drive air mix motor in upper right layer A1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (upper front passenger side air mix)

Pulse generation

(see waveform 8)

F7A-25 (B2RL) - Body Ground

-

Output to drive air mix motor in lower right layer B2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower front passenger side air mix)

Pulse generation

(see waveform 7)

F7A-26 (B1RL) - Body Ground

-

Output to drive air mix motor in lower right layer B1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower front passenger side air mix)

Pulse generation

(see waveform 7)

F7A-27 (A2RU) - Body Ground

-

Output to drive air mix motor in upper right layer A2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (upper front passenger side air mix)

Pulse generation

(see waveform 8)

F7A-28 (A1RL) - Body Ground

-

Output to drive air mix motor in lower right layer A1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower front passenger side air mix)

Pulse generation

(see waveform 7)

F7A-29 (B2RU) - Body Ground

-

Output to drive air mix motor in upper right layer B2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (upper front passenger side air mix)

Pulse generation

(see waveform 8)

F7A-30 (A2LU) - Body Ground

-

Output to drive air mix motor in upper left layer A2

  • Ignition Switch in ON position
  • No. 1 A/C Radiator Damper Servo Sub-assembly (upper driver side air mix) operation

Pulse generation

(see waveform 6)

F7A-31 (B2LU) - Body Ground

-

Output to drive air mix motor in upper left layer B

  • Ignition Switch in ON position
  • No. 1 A/C Radiator Damper Servo Sub-assembly (upper driver side air mix) operation

Pulse generation

(see waveform 6)

F7A-32 (BAO) - Body Ground

-

Power supply to motor to switch mode

Ignition Switch in ON position

11 à 14 V

F7A-33 (BRU) - Body Ground

-

Power supply to air mix motor in upper right layer

Ignition Switch in ON position

11 à 14 V

F7A-34 (BRL) - Body Ground

-

Power supply to air mix motor in lower right layer

Ignition Switch in ON position

11 à 14 V

F7A-35 (B1LL) - Body Ground

-

Output to drive air mix motor in lower left layer B1

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower driver side air mix)

Pulse generation

(see waveform 5)

F7A-36 (A1LU) - Body Ground

-

Output to drive air mix motor in upper left layer A1

  • Ignition Switch in ON position
  • No. 1 A/C Radiator Damper Servo Sub-assembly (upper driver side air mix) operation

Pulse generation

(see waveform 6)

F7A-37 (A2LL) - Body Ground

-

Output to drive air mix motor in lower left layer A2

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower driver side air mix)

Pulse generation

(see waveform 5)

F7A-38 (TEA) - F7A-39 (SGA)

-

No. 1 cooler thermistor input

  • Ignition Switch in ON position
  • Evaporator Temperature: 0 °C

0,5 V

  • Ignition Switch in ON position
  • Evaporator Temperature: 25 °C

1,6 V

F7A-39 (SGA) - Body Ground

-

Ground for No. 1 cooler thermistor

Always

Below 1 V

F7A-40 (BLW) - F72-29 (GND)

-

Output to drive blower motor

  • Ignition Switch in ON position
  • Blower Switch: Lo

Pulse generation

(see waveform 9)

  • *1: With ion generator
  • *2: with PTC heater

(a) Waveform 1:

Item

Content

Terminal No.

F72-3 (LIN1) - F72-29 (GND)

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

Ignition Switch in ON position

(b) Waveform 2:

Item

Content

Terminal No.

F72-15 (SOL-) - F72-29 (GND)

Oscilloscope Setting

5 V/DIV., 1 ms/DIV.

Vehicle Operating Conditions

  • Engine is running
  • Blower Switch: Lo
  • A/C Switch: ON

(c) Waveform 3:

Item

Content

Terminal No.

F7A-2 (B2AI) - Body Ground

F7A-3 (A2AI) - Body Ground

F7A-9 (A1AI) - Body Ground

F7A-10 (B1AI) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • No. 1 Blower Damper Servo Assembly (outside air/recirculation air) operating

(d) Waveform 4:

Item

Content

Terminal No.

F7A-4 (A2AO) - Body Ground

F7A-6 (B2AO) - Body Ground

F7A-8 (B1AO) - Body Ground

F7A-16 (A1AO) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • No. 2 Air Conditioning Radiator Damper Servo Assembly (mode switching) operating

(e) Waveform 5:

Item

Content

Terminal No.

F7A-18 (B2LL) - Body Ground

F7A-20 (A1LL) - Body Ground

F7A-35 (B1LL) - Body Ground

F7A-37 (A2LL) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower driver side air mix)

(f) Waveform 6:

Item

Content

Terminal No.

F7A-19 (B1LU) - Body Ground

F7A-30 (A2LU) - Body Ground

F7A-31 (B2LU) - Body Ground

F7A-36 (A1LU) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • No. 1 A/C Radiator Damper Servo Sub-assembly (upper driver side air mix) operation

(g) Waveform 7:

Item

Content

Terminal No.

F7A-23 (A2RL) - Body Ground

F7A-25 (B2RL) - Body Ground

F7A-26 (B1RL) - Body Ground

F7A-28 (A1RL) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (lower front passenger side air mix)

(h) Waveform 8:

Item

Content

Terminal No.

F7A-22 (B1RU) - Body Ground

F7A-24 (A1RU) - Body Ground

F7A-27 (A2RU) - Body Ground

F7A-29 (B2RU) - Body Ground

Oscilloscope Setting

2 V/DIV., 10 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • Operation of No. 1 A/C Radiator Damper Servo Sub-assembly (upper front passenger side air mix)

(i) Waveform 9:

Item

Content

Terminal No.

F7A-40 (BLW) - F72-29 (GND)

Oscilloscope Setting

2 V/DIV., 1 ms/DIV.

Vehicle Operating Conditions

  • Ignition Switch in ON position
  • Blower Switch: Lo

AIR CONDITIONING CONTROL ASSEMBLY

HINT:

Check the rear of the connector while it is connected to the air conditioning control assembly.

Terminal No. (Symbol)

Wire Color

Terminal Description

Condition

Specified Condition

F61-2 (LIN1) - Body Ground

L - Body ground

LIN communication

Ignition Switch in ON position

Pulse generation (see waveform 1)

F61-10 (IG+) - Body ground

BE - Body ground

Power supply (IG)

Ignition Switch in OFF position

Below 1 V

Ignition Switch in ON position

11 à 14 V

F61-16 (GND) - Body Ground

W-B - Body ground

Ground for Air Conditioning Control Assembly

Always

Below 1 V

(a) Waveform 1:

Item

Content

Terminal No.

F61-2 (LIN1) - Body Ground

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

Ignition Switch in ON position