Heater / Air Conditioning

Cabin Temperature Sensor Circuit (B1411)

~4min read

DESCRIPTION

The cooler thermistor (cabin temperature sensor) is mounted on the instrument panel to detect the cabin temperature, which is used to control the air conditioning system. The resistance of the cooler thermistor (cabin temperature sensor) changes according to the cabin temperature. Resistance increases as temperature decreases. Resistance decreases as temperature increases.

The air conditioning amplifier assembly applies a voltage (5 V) to the cooler thermistor (cabin temperature sensor) and detects the voltage change caused by the change in resistance of the cooler thermistor (cabin temperature sensor).

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

B1411

Cabin Temperature Sensor Circuit

One of the following conditions is met

  • Open in Cooler Thermistor (Room Temperature Sensor) Circuit
  • Short circuit in cooler thermistor (cabin temperature sensor)
  • Cooler Thermistor (Room Temperature Sensor)
  • Wire harness or connector between the cooler thermistor (room temperature sensor) and the air conditioning amplifier assembly
  • Air Conditioning Amplifier Assembly

Stored

(4 seconds minimum)*

  • *: The A/C amplifier assembly stores this DTC if the malfunction occurs within the time period shown in parentheses.

HINT:

If the cabin temperature is approximately -56.0 °C or lower, DTC B1411 may be output even if the system is normal.

DTC Detection Conditions

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

Ignition Switch in ON position

○

○

Malfunction Status

Open in Cooler Thermistor (Room Temperature Sensor) Circuit

○

-

Short circuit in cooler thermistor (cabin temperature sensor)

-

○

Detection Duration

4 seconds minimum

4 seconds minimum

Number of Trips

1 trip(s)

1 trip(s)

HINT:

The DTC is output when the conditions for any one of the sequences in the table above are met.

WIRING DIAGRAM

PROCEDURE

  1. READ VALUE USING TECHSTREAM (ROOM TEMPERATURE SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menu items: Body Electrical / Air Conditioner / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Air Conditioner > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Room Temperature Sensor

Cooler Thermistor (Room Temperature Sensor)

Min.: -6,50 °C

Max.: 57 °C

Actual Room Temperature Displayed

-

Body Electrical > Air Conditioner > Data List

Room Temperature Sensor

OK:

The displayed value is within the specifications in the normal condition column.

Result:

Result

Proceed to

NG

A

OK (when troubleshooting is performed based on the Symptom Chart)

B

OK (when troubleshooting is performed using DTC)

C

B

GO TO APPLICABLE SYSTEM AS INDICATED IN THE PROBLEM SYMPTOMS TABLE

C

GO TO STEP 4

A
  1. INSPECT COOLER THERMISTOR (CABIN TEMPERATURE SENSOR)

(a) Remove the cooler thermistor (cabin temperature sensor).

Click here

(b) Inspect the cooler thermistor (cabin temperature sensor).

Click here

NG

REPLACE COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (COOLER THERMISTOR (CABIN TEMPERATURE SENSOR) - AIR CONDITIONING AMPLIFIER ASSEMBLY)

(a) Disconnect the F72 connector from the air conditioning amplifier assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F72-30 (TR) - F60-1

Always

Below 1 Ω

F72-31 (SG-1) - F60-2

Always

Below 1 Ω

F72-30 (TR) or F60-1 - Body ground

Always

10 kΩ minimum

F72-31 (SG-1) or F60-2 - Body ground

Always

10 kΩ minimum

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Air Conditioner > Clear DTCs

(b) Check DTCs.

Click here

Body Electrical > Air Conditioner > Trouble Codes

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY