Heater / Air Conditioning

Ambient Temperature Sensor Circuit (B1412)

~4min read

DESCRIPTION

The thermistor assembly is mounted at the front of the cooler condenser assembly to detect the ambient temperature used to control the air conditioning system. This sensor is connected to the combination meter assembly and detects ambient temperature fluctuations. This data is used to control the cabin temperature. The sensor sends a signal to the combination meter assembly. The resistance of the thermistor assembly changes according to the ambient temperature. Resistance increases as temperature decreases. Resistance decreases as temperature increases.

The combination meter assembly applies a voltage (5 V) to the thermistor assembly and detects voltage changes based on changes in the resistance of the thermistor assembly.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

B1412

Ambient Temperature Sensor Circuit

When the A/C amplifier assembly receives outside air temperature sensor data outside the allowable range from the combination meter assembly.

  • Thermistor Assembly
  • Wire harness or connector between the thermistor assembly and the combination meter assembly
  • Air Conditioning Amplifier Assembly
  • Combination meter assembly
  • CAN communication system

Stored

(4 seconds minimum)*

  • *: The A/C amplifier assembly stores this DTC if the malfunction occurs within the time period shown in parentheses.

HINT:

If the ambient temperature is approximately -80.0 °C or lower, DTC B1412 may be output even if the system is normal.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

When replacing the instrument cluster assembly, always use a new part. If an instrument cluster assembly that was installed in another vehicle is used, the stored information will not match the information transmitted by the vehicle, and a DTC may be stored.

PROCEDURE

  1. INSPECT CAN COMMUNICATION SYSTEM

(a) Check whether CAN communication system DTCs are output.

Click here

Result:

Result

Proceed to

CAN communication DTCs are not output.

A

CAN communication DTCs are output.

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. READ VALUE USING TECHSTREAM (AMBIENT TEMPERATURE)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Body Electrical / Combination Meter / Data List.

(e) Read the Data List by following the instructions on the Techstream.

Body Electrical > Combination Meter > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Ambient Temperature

Ambient Temperature

Min.: -40°C (-40°F)

Max.: 88 °C

Almost the same as the actual ambient temperature

The multi-information display shows a temperature from -40 to 50 °C

Body Electrical > Combination Meter > Data List

Ambient Temperature

OK:

The displayed value is within the specifications in the normal condition column.

Result:

Result

Proceed to

NG

A

OK (when troubleshooting is performed based on the Symptom Chart)

B

OK (when troubleshooting is performed using DTC)

C

B

AIR CONDITIONING AMPLIFIER ASSEMBLY

C

GO TO STEP 5

A
  1. INSPECT THERMISTOR ASSEMBLY

(a) Remove the thermistor assembly.

Click here

(b) Inspect the thermistor assembly.

Click here

NG

REPLACE THERMISTOR ASSEMBLY

OK
  1. INSPECT WIRE HARNESS AND CONNECTOR (THERMISTOR ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect connector A3 from the thermistor assembly.

(b) Disconnect the combination meter assembly connector F4.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F4-34 (TEMP) - A3-2

Always

Below 1 Ω

F4-35 (TX1+) - A3-1

Always

Below 1 Ω

F4-34 (TEMP) or A3-2 - Body ground

Always

10 kΩ minimum

F4-35 (TX1+) or A3-1 - Body ground

Always

10 kΩ minimum

OK

REPLACE COMBINATION METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Clear the DTCs.

Click here

Body Electrical > Air Conditioner > Clear DTCs

(b) Check DTCs.

Click here

Body Electrical > Air Conditioner > Trouble Codes

Result:

Result

Proceed to

No DTCs are output

A

DTCs are output

B

A

USE SIMULATION METHOD TO CHECK

B

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY