Heater / Air Conditioning

System Description

~13min read

SYSTEM DESCRIPTION

GENERAL

The air conditioning system is equipped with the following controls:

Control

General Description

Neural Network Control

This control performs complex control by artificially simulating the information processing method of the nervous system of living organisms, in order to establish a complex input/output relationship similar to that of the human brain.

Discharge Air Temperature Control

Based on the temperature set with the temperature selector, the neural network control calculates the discharge air temperature from the input signals sent by various sensors.

Independent Left and Right Control

The temperature settings for the driver and front passenger are controlled independently, so that the interior temperature can differ between the left and right sides of the cabin. This provides air conditioning suited to each occupant's preference.

Blower Control

Controls the blower motor based on the airflow calculated by the neural network control, using input signals sent by various sensors.

Air Outlet Control

Automatically switches the air outlets according to the air outlet mode calculated by the neural network control.

Based on engine coolant temperature, outside air temperature, amount of sunlight, required blower airflow, discharge air temperature and vehicle speed, this control automatically switches the blower outlet to floor/defrost mode to prevent fogging of the windows when the outside air temperature is low.

Air Inlet Control

Automatically controls the air inlet control damper to help achieve the calculated required discharge air temperature.

Drives the air inlet control servo motor according to the operation of the air inlet control switch, and moves the dampers to the Recirculated Air/Fresh Air position.

Variable Capacity Compressor Control

Controls the compressor assembly with pulley to engage or disengage it, and adjusts the discharge capacity based on signals sent by various sensors.

Defogger Control

The defogger control logic is used to improve defogger performance.

Parked Car Outside Air Control

Automatically switches to outside air mode when the vehicle is parked. This makes it easier to ventilate the parked vehicle and introduces outside air into the air conditioning unit assembly.

Blower Customize

During automatic air conditioning operation, the air volume can be set to 3 different levels using the A/C control assembly (FAST/ECO switch): NORMAL → ECO (low air volume) → FAST (high air volume).

Diagnosis

A diagnostic trouble code (DTC) is stored in memory when the air conditioning amplifier assembly detects a malfunction in the air conditioning system.

NEURAL NETWORK CONTROL

  • In previous automatic air conditioning systems, the air conditioning amplifier assembly determined the outlet air temperature and the required blower air volume using a calculation formula based on information from the sensors.

    However, because human perception is complex, a given temperature may feel different depending on the environment the occupant is in. For example, a given level of sunlight may feel pleasantly warm in cold weather, or very uncomfortable in hot weather. For this reason, a neural network has been adopted in the automatic air conditioning system to achieve more precise control. Using this technology, data collected under various weather conditions is stored in the air conditioning amplifier assembly. The amplifier can therefore control the system to provide improved air conditioning comfort.

  • The neural network control consists of neurons in the input, intermediate and output layers. The input layer neurons process the data received for outside air temperature, sunload and cabin temperature based on the data supplied by the switches and sensors, then transmit it to the intermediate layer neurons. Based on this data, the intermediate layer neurons adjust the strength of the connections between neurons. The output layer neurons then calculate their sum as the outlet air temperature, solar correction, target airflow and required outlet mode control volume. The air conditioning amplifier assembly accordingly controls the servo motors and the blower motor according to the control volumes calculated by the neural network control.

MODE POSITION AND DAMPER OPERATION

Mode position and damper operation

*A

for manual air conditioning system

*B

for automatic air conditioning system

*1

Driver side air mix control damper

*2

Front passenger side air mix control damper

*3

Driver side defroster

*4

Front defroster

*5

Front passenger side defroster

*6

Air inlet control damper (lower side)

*7

Air inlet control damper (upper side)

*8

Air purification filter

*9

Blower motor sub-assembly with fan

*10

No. 1 cooler evaporator sub-assembly

*11

Air mix control damper

*12

Heater unit sub-assembly

*13

Mode switching damper

*14

Driver side floor register

*15

Front passenger side floor register

*16

Driver side register

*17

Center register

*18

Front passenger side register

*19

Quick heating assembly

*20

Rear left floor register

*21

Rear right floor register

-

-

*a

View of diagram from [A]

*b

View [A]

*c

Recirculated air

*d

Outside air

Main Damper Functions

Control damper

Operation position

Damper position

Operation

Air inlet control damper

FRESH

A1

Allows outside air to enter.

RECIRCULATION

A2

Recirculates inside air.

Air mix control damper

HI - LO

B1 - B2

Varies the mix ratio of cool and warm air on the driver side to continuously control the temperature from HI to LO.

C2 - C1

Varies the mix ratio of cool and warm air on the front passenger side to continuously control the temperature from HI to LO.

Air outlet damper

DEF

E, G, J

Defrosts the windshield using the center defroster, side defrosters and side registers.

FOOT/DEF

E, G, I à J

Defrosts the windshield through the center defroster, side defrosters and side registers while blowing air from the front floor duct registers.

FOOT

D, (D à E), G, I

Air is blown from the front floor duct registers and side registers. Air also blows slightly from the center defroster and side defrosters.

B/L

D, F à H, I à J

Air is blown from the center registers, side registers and front floor duct registers.

FACE

D, F, J

Air blows from the center registers and side registers.

AIR OUTLETS AND AIRFLOW VOLUME

The size of each circle ○ indicates the airflow volume ratio.

(a) Air outlets and airflow.

Mode

FACE

FOOT

DEF

Center

Side

Front

Rear*1

Center

Side

A

B

C

D

E

F

FACE

B/L

FOOT

FOOT/DEF

DEF

  • *1: with PTC heater

OUTSIDE AIR INTRODUCTION DURING PARKING CONTROL

When 60 seconds have elapsed after the ignition switch is turned to OFF, the air conditioning amplifier assembly uses control logic that automatically switches the air inlet to "FRESH" mode to purge unwanted odors from the air conditioning unit.

This control logic reduces unwanted odors when the air conditioning system is started.

COMPRESSOR

(a) General:

(1) The compressor is a continuously variable capacity type, and its capacity changes according to the cooling load of the air conditioning system.

*1

Shaft

*2

Control valve

(b) Control valve operation:

(1) The crank chamber is connected to the suction passage. A control valve is located between the suction passage (low pressure) and the discharge passage (high pressure).

(2) The control valve operates under duty cycle control based on signals from the air conditioning amplifier assembly.

*1

Suction passage

*2

Crank chamber

*3

Piston

*4

Discharge passage

*5

Control valve

*6

Air Conditioning Amplifier Assembly

(3) When the control valve closes (solenoid coil energized), a pressure change is created and the pressure in the crank chamber decreases. As a result, the pressure acting on the right side of the piston becomes higher than the pressure acting on the left side of the piston. This compresses the spring and tilts the swash plate. Consequently, the piston stroke increases, along with the discharge capacity.

*1

Suction passage

*2

Crank chamber

*3

Piston

*4

Discharge passage

*5

Control valve

*6

Air Conditioning Amplifier Assembly

*a

Piston stroke: Large

*b

Suction chamber pressure + Spring force

(4) When the control valve opens (solenoid coil not energized), the pressure difference disappears. As a result, the pressure acting on the right side of the piston and the pressure acting on the left side of the piston balance out. The spring then extends and cancels the tilt of the swash plate. Consequently, there is no piston stroke and the discharge capacity decreases.

*1

Suction passage

*2

Crank chamber

*3

Piston

*4

Discharge passage

*5

Control valve

*6

Air Conditioning Amplifier Assembly

*a

Piston stroke: Small

*b

Suction chamber pressure + Spring force

(c) CS Valve Operation:

(1) The CS valve has passage A and passage B. If the vehicle is parked for a long period, refrigerant may accumulate in the crank chamber due to the difference in heat capacity.

(2) The control solenoid valve is controlled by the A/C amplifier assembly. When the compressor operates, the control solenoid valve lowers the CS valve rod and opens passage A.

(3) Under the above conditions, the pressure in the crank chamber can only become high if a quantity of refrigerant has accumulated in the crank chamber. Therefore, due to the pressure difference with the internal pressure (negative pressure), the bellows contract and open passage B.

(4) This causes the accumulated refrigerant to be discharged through passages A and B, eliminating the previously accumulated refrigerant and ensuring a more immediate cooling effect.

ION GENERATOR SUB-ASSEMBLY (with Ion Generator)

(a) The ion generator sub-assembly operates when the blower switch is in the ON position.

(b) The ion generator assembly emits electrically charged "nanoe" ions encapsulated with water. The ions are discharged into the cabin through the side louver (front passenger side) to provide clean, non-irritating air for the skin.*

CAUTION:

Do not attempt to disassemble or repair the ion generator assembly as it contains high-voltage components.

NOTICE:

Do not insert anything into the side louver (front passenger side), attach anything to it, or spray anything nearby. This may cause the ion generator assembly to malfunction.

HINT:

  • *: Depending on temperature and humidity conditions, blower speed, and the selected air outlet mode, the ion generator assembly may not operate at full capacity.
  • When the ion generator assembly operates, a small amount of ozone is emitted and may occasionally cause a slight odor. However, this amount is similar to that found in nature, such as in forests, and has no effect on the human body.
  • A slight noise may be heard during operation. This does not indicate a malfunction.

*1

Ion Generator Assembly

*2

Air Conditioning Control Assembly (nanoe indicator)

*a

Common Negative Ion

*b

"nanoe" Ion

*c

H2O

*d

Electron

HINT:

"nanoe" is a registered trademark of Panasonic Co., Ltd.

NO. 1 COOLER THERMISTOR (EVAPORATOR TEMPERATURE SENSOR)

The No. 1 cooler thermistor (evaporator temperature sensor) detects the temperature of the cold air that has passed through the evaporator as changes in resistance, and sends it to the air conditioning amplifier assembly.

BLOWER MOTOR SUB-ASSEMBLY WITH FAN

The blower motor is controlled by the service control exercised via the blower resistor from the air conditioning amplifier assembly.

BLOWER RESISTOR

The blower resistor controls the blower motor with the blower fan assembly according to changes in the signal sent by the air conditioning amplifier assembly.

SERVO MOTOR

The servomotor uses a stepper-type motor. The motor, with four coils, continuously applies battery voltage. The air conditioning amplifier assembly repeatedly switches ON and OFF the voltage of each coil in sequence, as many times as needed, to move to the target position.

RAPID HEATER ASSEMBLY (with PTC heater)

(a) General

(1) The quick heater assembly is located on the heater core in the air conditioning radiator assembly.

(2) The quick heater assembly consists of a PTC heater element, aluminum fins and brass plates. When current is applied to the PTC heater element, it generates heat that warms the air passing through the unit.

*1

Quick heating assembly

*2

Heat-resistant resin plate

*3

End

-

-

(b) Quick heater assembly operating conditions

(1) The quick heater assembly is turned on and off by the air conditioning assembly based on the engine coolant temperature, outside air temperature, temperature setting and electrical load (generator power ratio).

COOLER THERMISTOR (ROOM TEMPERATURE SENSOR)

The cooler thermistor (room temperature sensor) detects the cabin temperature based on changes in the resistance of its built-in thermistor and sends a signal to the air conditioning amplifier assembly.

THERMISTOR ASSEMBLY

The thermistor assembly detects the outside temperature based on changes in the resistance of its built-in thermistor and sends a signal to the instrument cluster assembly. Through CAN communication, it sends outside temperature information to the air conditioning amplifier assembly.

AUTOMATIC LIGHT CONTROL SENSOR

The auto light control sensor detects changes in the degree of sunlight (as changes in the current flowing through the built-in photodiode) and sends these sunlight level signals to the air conditioning amplifier assembly.

AIR CONDITIONING PRESSURE SENSOR

The air conditioning pressure sensor detects the refrigerant pressure and sends it to the air conditioning amplifier assembly as voltage changes.