Heater / Air Conditioning

Lost Communication with Front Panel LIN (B14B2)

~3min read

DESCRIPTION

The air conditioning control assembly communicates with the air conditioner amplifier assembly via LIN communication.

If the LIN communication system malfunctions, the air conditioner amplifier assembly does not operate even if the air conditioning control assembly is operated.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Memory

B14B2

Communication Lost with LIN Front Panel

Communication Lost with A/C Control Assembly

  • Wire harness or connector between air conditioning control assembly and power source
  • Harness or connector between the air conditioning control assembly and the body ground
  • LIN Communication System
  • Air Conditioning Control Assembly
  • Air Conditioning Amplifier Assembly

Stored

(10 seconds minimum)*

  • *: The A/C amplifier assembly stores this DTC if the malfunction occurs within the time period shown in parentheses.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

Check the fuses for the circuits related to this system before performing the following procedure.

PROCEDURE

  1. CHECK WIRE HARNESS AND CONNECTOR (AIR CONDITIONING CONTROL ASSEMBLY - POWER SOURCE)

(a) Disconnect the air conditioning control assembly connector.

*a

Front view of wire harness side connector

(to Air Conditioning Control Assembly)

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Ignition switch position

Specified Condition

F61-10 (IG+) - Body ground

Ignition Switch in ON position

11 à 14 V

F61-10 (IG+) - Body ground

Ignition Switch in OFF position

Below 1 V

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Ignition switch position

Specified Condition

F61-16 (GND) - Body ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE WIRE HARNESS OR CONNECTOR (POWER SOURCE CIRCUIT)

OK
  1. CHECK HARNESS AND CONNECTOR (AIR CONDITIONER AMPLIFIER ASSEMBLY - AIR CONDITIONING CONTROL ASSEMBLY)

(a) Disconnect the F72 connector from the air conditioning amplifier assembly.

(b) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F61-2 (LIN1) - F72-3 (LIN1)

Always

Below 1 Ω

F61-2 (LIN1) or F72-3 (LIN1) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK AIR CONDITIONING AMPLIFIER ASSY

(a) Reconnect the F72 connector of the air conditioning amplifier assembly.

(b) Turn the ignition switch to ON.

(c) Connect an oscilloscope to terminals F72-3 (LIN1) and F72-29 (GND) of the air conditioning amplifier assembly and check the waveform.

OK:

The waveform is the same as that shown in the diagram.

Item

Content

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

Ignition Switch in ON position

*a

Component with Wire Harness Connected

(A/C Amplifier Assembly)

-

-

NG

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

OK
  1. CHECK AIR CONDITIONING CONTROL ASSY

(a) Reconnect the F61 connector of the air conditioning control assembly.

(b) Turn the ignition switch to ON.

(c) Connect an oscilloscope to terminals F61-2 (LIN1) and F61-16 (GND) of the air conditioning control assembly and check the waveform.

OK:

The waveform is the same as that shown in the diagram.

Item

Content

Oscilloscope Setting

2 V/DIV., 20 ms/DIV.

Vehicle Operating Conditions

Ignition Switch in ON position

*a

Component with Wire Harness Connected

(air conditioning control assembly)

-

-

OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY

NG

REPLACE AIR CONDITIONING CONTROL ASSEMBLY