K114 Continuously Variable Transmission

Acceleration Sensor Circuit (P1585)

3steps
~18min
2/5difficulty
Done 0 of 3

DESCRIPTION

The ECM determines the vehicle inclination based on a signal transmitted by the airbag sensor assembly (yaw and acceleration sensor). If a malfunction is detected in the airbag sensor assembly (yaw and acceleration sensor) based on a malfunction signal transmitted by the skid control ECU (brake actuator assembly), the ECM stores this DTC.

HINT:

  • The airbag sensor assembly (yaw and acceleration sensor) signal is transmitted to the skid control ECU (brake actuator assembly) via CAN communication.
  • If other CAN communication DTCs are output, begin troubleshooting with those DTCs.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

MIL

Memory

P1585

Acceleration Sensor Circuit

After the ignition switch is turned ON, the skid control ECU (brake actuator assembly) detects one of the following conditions, and the ECM receives a diagnostic signal transmitted by the skid control ECU (brake actuator assembly) for at least 3 seconds (1 trip detection logic).

  • The output value of the airbag sensor assembly (yaw and acceleration sensor) remains at -1.5 G or less, or 1.5 G or more, for at least 1.2 seconds.
  • The power supply voltage of the airbag sensor assembly (yaw and acceleration sensor) is 4.4 V or less, or 5.6 V or more, for at least 1.2 seconds.
  • No signal is detected from the airbag sensor assembly (acceleration and yaw sensor) 7 times or more.
  • With the vehicle stopped, the difference between GL1 and GL2 does not fall below 0.4 G within 60 seconds after exceeding 0.6 G.
  • A power supply voltage malfunction signal from the airbag sensor assembly (yaw and acceleration sensor) is received for at least 10 seconds while the vehicle is driven at 3 km/h or more.
  • Airbag sensor assembly (yaw and acceleration sensor)
  • Brake actuator assembly (skid control ECU)
  • CAN communication system

Not activated

DTC recorded

DTC Detection Condition Sequence:

Vehicle Operating Conditions

Sequence 1

Sequence 2

Sequence 3

Sequence 4

Sequence 5

Diagnostic Condition

The ignition switch is in the ON position.

○

○

○

○

○

Malfunction condition

The output value of the airbag sensor assembly (yaw and acceleration sensor) remains at -1.5 G or less, or 1.5 G or more, for at least 1.2 seconds.

○

-

-

-

-

The power supply voltage of the airbag sensor assembly (yaw and acceleration sensor) is 4.4 V or less, or 5.6 V or more, for at least 1.2 seconds.

-

○

-

-

-

No signal from the airbag sensor assembly (acceleration and yaw sensor) is detected 7 times or more.

-

-

○

-

-

With the vehicle stopped, the difference between GL1 and GL2 does not fall below 0.4 G within 60 seconds after exceeding 0.6 G.

-

-

-

○

-

A power supply voltage malfunction signal from the airbag sensor assembly (yaw and acceleration sensor) is received for at least 10 seconds while the vehicle is driven at 3 km/h or more.

-

-

-

-

○

Duration

3 seconds minimum

3 seconds minimum

3 seconds minimum

3 seconds minimum

3 seconds minimum

Detection logic

1 trip detection logic

1 trip detection logic

1 trip detection logic

1 trip detection logic

1 trip detection logic

HINT:

This DTC is stored when one of the above detection sequences occurs.

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • Perform initialization after replacing any part related to the CVT system.

    Click here

  • Make sure no DTCs are stored after performing initialization.

    Click here

HINT:

After completing the repair, clear the DTCs and perform the following procedure to confirm that the DTCs are not output.

  1. Turn the ignition switch ON and wait at least 60 seconds.
  2. Perform the shift check and test in the D position during the road test.

    Click here

  3. Check whether any other DTCs are output.

    Click here

PROCEDURE

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Check the DTCs.

Powertrain > Engine and ECT > Trouble Codes

Result:

Result

Proceed to

DTC U0129 is not output

A

DTC U0129 is output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. READ VALUE USING TECHSTREAM (G SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List

G Sensor

(e) Depending on the Techstream display, record the Data List.

Powertrain > Engine and ECT > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

G Sensor

Yaw and acceleration sensor converted output voltage

Min.: 0 V

Max.: 79.998 V

Displays the converted output voltage of the yaw and acceleration sensor

  • 2.31 V to 2.69 V: Vehicle on level ground
  • 1.88 V to 2.5 V: Deceleration
  • 2.5 V to 3.11 V: Acceleration
  • Set to 1.87 V: Yaw and acceleration sensor malfunction
  • Fixed at 1.87 V: Communication malfunction

-

Result:

Result

Proceed to

The displayed data is not within the range shown under "Normal Condition".

A

The displayed data is within the range shown under "Normal Condition".

B

B

REPLACE BRAKE ACTUATOR ASSEMBLY

A
  1. REPLACE AIRBAG SENSOR ASSEMBLY

(a) Replace the airbag sensor assembly (yaw and acceleration sensor).

Click here

NEXT

PERFORM INITIALIZATION