K114 Continuously Variable Transmission

Initialization

~4min read

INITIALIZATION

NOTICE:

  • Performing the memory reset will erase the learned values for the yaw and acceleration sensor (deceleration sensor zero point calibration) and the CVT oil pressure (CVT oil pressure calibration). Be sure to perform the memory reset, the yaw and acceleration sensor zero point calibration, and the CVT oil pressure calibration when replacing the parts shown in the following table:
    • Continuously variable transaxle assembly
    • ECM
    • Oil pressure sensor
    • Airbag sensor assembly (yaw and acceleration sensor)
  • After resetting the memory, always perform the yaw and acceleration sensor calibration (deceleration sensor zero point) first, then perform the CVT oil pressure calibration.

MEMORY RESET/CALIBRATION

(a) Reset the memory as follows:

(1) Turn the ignition switch OFF.

(2) Move the shift lever to P and apply the parking brake.

(3) Connect the Techstream to the DLC3.

(4) Turn the ignition switch ON.

NOTICE:

Do not start the engine.

(5) Turn on the Techstream.

(6) Select the following menu items: Powertrain / Engine and ECT / Utility / Reset Memory.

NOTICE:

  • Keep the vehicle stationary, on a level and stable surface during calibration (inclination: 0 +/- 0.25°).
  • Make sure the shift lever is in the P position.
  • Make sure the engine is off. To prevent idle vibration, do not start the engine.
  • Make sure the ignition switch is in the ON position.
Powertrain > Engine and ECT > Utility

Reset Memory

(b) Perform the deceleration sensor zero point calibration as follows:

(1) Turn the ignition switch to ON and wait at least 2 seconds.

(2) Select the following menu items: Powertrain / Engine and ECT / Utility / Deceleration Sensor Zero Point Calibration.

HINT:

  • When the message "Complete" appears on the screen, the deceleration sensor zero point calibration is finished.
  • If "Error" appears on the screen and DTC P1589 is stored (for DTC P1589 detection conditions), refer to P1589 because the deceleration sensor circuit may be malfunctioning.

    Click here

  • If the vehicle is shaken or vibrates during zero point calibration, the procedure may be cancelled. If "Error" appears on the screen and DTC P1589 is not stored, perform the calibration again.
Powertrain > Engine and ECT > Utility

Deceleration Sensor Zero Point Calibration

(c) Perform the CVT oil pressure calibration as follows:

(1) Turn the ignition switch to OFF and wait at least 30 seconds.

(2) Turn the ignition switch to ON and wait at least 2 seconds.

NOTICE:

Do not start the engine.

HINT:

The CVT oil pressure calibration is performed with the ignition switch in the ON position (engine off). However, the calibration cannot be performed when the following conditions are met:

  • The oil pressure sensor value is 0.065 MPa (0.663 kgf/cm², 9.43 psi) or higher.
  • The CVT fluid temperature is -5°C (23°F) or lower, or 120 °C or higher.

(3) Start the engine and wait at least 5 seconds.

(4) Select the following menu items: Powertrain / Engine and ECT / Utility / CVT Oil Pressure Calibration.

HINT:

  • During CVT oil pressure calibration, the engine idle speed will increase.
  • When the message "Complete" appears on the screen, the CVT oil pressure calibration is finished.
  • Learned values cannot be cleared by simply disconnecting and reconnecting the cable from the negative (-) battery terminal.
Powertrain > Engine and ECT > Utility

CVT Oil Pressure Calibration

ATF THERMAL DEGRADATION ESTIMATE RESET

NOTICE:

If any of the following conditions is met, perform the ATF thermal degradation estimate reset.

  • The CVT fluid has been replaced.

    HINT:

    If at least 50,000 is displayed for the Data List item "ATF Thermal Degradation Estimate", CVT fluid thermal degradation is likely. Perform the ATF thermal degradation estimate reset after replacing the CVT fluid.

  • Approximately 50% or more of the CVT fluid was replaced during transaxle repair or a similar procedure.

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

NOTICE:

Do not start the engine.

(d) Turn on the Techstream.

(e) Select the following menu items: Powertrain / Engine and ECT / Utility / ATF Thermal Degradation Estimate Reset.

Powertrain > Engine and ECT > Utility

ATF Thermal Degradation Estimate Reset