K114 Continuously Variable Transmission

Data List / Active Test

~16min read

DATA LIST / ACTIVE TEST

DATA LIST

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

(a) Warm up the engine.

(b) Turn the ignition switch OFF.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to the ON position.

(e) Turn on the Techstream.

(f) Select the following menu items: Powertrain / Engine and ECT / Data List.

HINT:

  • To display the list, press the button next to Primary in the drop-down menu. Then select a data group.
  • When a data group is selected, the ECM data for that group is displayed.
  • Data List Group / Description
    • All Data / All data
    • Primary / -
    • Engine Control / Engine control system data
    • Check Mode / Check mode data
    • Automatic Transmission System Data / AT.
    • Vehicle Information / Vehicle information

(g) Check the Data List displayed on the Techstream.

Powertrain > Engine and ECT > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Vehicle Speed

Vehicle speed

Min.: 0 km/h

Max.: 255 km/h

Actual vehicle speed

  • This is the current vehicle speed.
  • Vehicle speed is detected by the wheel speed sensors.
  • Vehicle speed data is delayed when displayed. Therefore, even if the vehicle speed recorded in the freeze frame data is 0 km/h, this does not always mean that the malfunction occurred while the vehicle was stopped.

Engine Speed

Engine speed

Min.: 0 rpm

Max.: 16,383 rpm

710 to 810 rpm: at idle

If the crankshaft position sensor malfunctions, "Engine Speed" is approximately 0 rpm or fluctuates significantly from the actual engine speed

MAF

Mass air flow meter air flow rate

Min.: 0 g/s.

Max.: 655.35 g/s.

  • 1.0 to 3.0 g/s: at idle
  • 3.0 to 8.0 g/s: 3,000 rpm (no load)

This is the intake air volume from the mass air flow meter.

Coolant Temp

Engine Coolant Temperature

Min.: -40°C (-40°F)

Max.: 140 °C

75 to 100 °C: after warm-up

  • After the engine has warmed up, the engine coolant temperature is 75 to 100 °C.
  • After the engine has been stopped for a long time, the engine coolant temperature, intake air temperature and ambient temperature are almost the same.
  • Check whether the engine is overheating if the value indicates 140 °C.

Throttle Motor DUTY

Throttle Actuator

Min.: 0 %

Max.: 100 %

10 to 22 %: at idle

This is the output duty ratio of the throttle actuator control circuit.

N Range Status

Estimated shift lever N position

OFF or ON

  • ON: Shift lever in P or N
  • OFF: Shift lever in a position other than P or N

-

Starter Signal

Starter signal

OFF or ON

  • ON: Starter operating
  • OFF: Starter not activated

-

Neutral Position SW Signal

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in P or N
  • OFF: Shift lever in a position other than P or N

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

Stop Light Switch

Brake Light Switch Position

OFF or ON

  • ON: Brake pedal depressed
  • OFF: Brake pedal released

-

A/C Signal

A/C Switch Status

OFF or ON

ON: A/C switch on

-

Closed Throttle Position SW

Throttle Valve Fully Closed Position Switch

OFF or ON

  • ON: Throttle valve fully closed
  • OFF: Throttle valve open

-

TC and TE1

DLC3 TC and CG (TE1) Terminals

OFF or ON

-

-

SPD (NT)

Input Turbine Speed

Min.: 0 rpm

Max.: 12,750 rpm

  • Input turbine speed (NT) equal to engine speed (NE): Lock-up ON (after engine warm-up)
  • Input turbine speed (NT) nearly equal to engine speed (NE): Lock-up OFF (engine at idle, shift lever in P or N position)
  • 0 rpm: Vehicle stopped, shift lever in R position

Data is displayed in 50 rpm increments.

Shift SW Status (P Range)

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in P position
  • OFF: Shift lever in a position other than P

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

Pattern Switch (PWR/M)

Sport Mode Position

OFF or ON

  • ON: Sport mode switch on
  • OFF: Sport mode switch off

-

Shift SW Status (R Range)

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in R position
  • OFF: Shift lever in a position other than R

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

Shift SW Status (N Range)

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in N position
  • OFF: Shift lever in position other than N

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

Shift SW Status (N,P Range) Supported

Shift Lever P or N Position Support Status

Supp or Unsupp

Supp: Normal

-

Shift SW Status (N,P Range)

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in P or N
  • OFF: Shift lever in a position other than P or N

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

Sports Shift Up SW

Sport Mode Upshift Switch Position

OFF or ON

  • ON: Shift lever held in "+"
  • OFF: Shift lever not held in "+"

-

Sports Shift Down SW

Sport Mode Downshift Switch Position

OFF or ON

  • ON: Shift lever held in "-"
  • OFF: Shift lever not held in "-"

-

Sports Mode Selection SW

Sport mode select switch position

OFF or ON

  • ON: Shift lever in M position, "+" or "-"
  • OFF: Shift lever in a position other than M, "+" or "-"

-

Shift SW Status (D Range)

Park/Neutral Position Switch Status

OFF or ON

  • ON: Shift lever in D or M position
  • OFF: Shift lever in a position other than D or M

If the shift lever position indicated by the Techstream differs from the actual position, the park/neutral position switch or shift cable adjustment may be incorrect.

HINT:

If the same malfunction is still detected after adjusting these parts, refer to DTC P0705. *3

A/T Oil Temperature 1

CVT fluid temperature sensor value

Min.: -40°C (-40°F)

Max.: 150 °C

  • After stall speed test: approx. 100 °C
  • Same as ambient temperature at cold start

If the value is -40°C (-40°F) or 150 °C or less, the CVT fluid temperature sensor circuit is open or shorted.

ATF Thermal Degradation Estimate

Estimated CVT fluid thermal degradation value

Min.: 0

Max.: 65,535

-

If at least 50,000 is displayed for the Data List item "ATF Thermal Degradation Estimate", CVT fluid thermal degradation is likely. Perform the ATF thermal degradation estimate reset after replacing the CVT fluid.

NT Sensor Voltage

Input turbine speed sensor (NT) output voltage

Min.: 0.000 V

Max.: 4.999 V

0.2 to 1.8 V: Engine idling (vehicle stopped, shift lever in P or N position)

-

SPD (NIN)

Primary pulley speed (NIN)

Min.: 0 rpm

Max.: 12,750 rpm

  • 0 rpm: Vehicle stopped
  • Primary pulley speed (NIN) same as engine speed (NE): Lock-up ON (after engine warm-up)

Data is displayed in 50 rpm increments.

SPD (NOUT)

Secondary pulley speed (NOUT)

Min.: 0 rpm

Max.: 12,750 rpm

  • 0 rpm: Vehicle stopped
  • Approx. 2,500 rpm*1 or 2,800 rpm*2: Vehicle traveling at approx. 60 km/h

Data is displayed in 50 rpm increments.

NOUT Sensor Voltage

Secondary pulley speed sensor (NOUT) output voltage

Min.: 0.000 V

Max.: 4.999 V

0.2 to 1.8 V: Engine idling (vehicle stopped, shift lever in P or N position)

-

A/T Oil Pressure

Secondary oil pressure value

Min.: -64 MPa

Max.: 63.998 MPa

Secondary oil pressure check:

  • 3.9 to 4.7 MPa (39.8 to 47.9 kgf/cm2, 566 to 682 psi): Stall speed test in D position
  • 3.7 to 4.9 MPa (37.7 to 50.0 kgf/cm2, 537 to 711 psi): Stall speed test in R position

-

G Sensor

Yaw and acceleration sensor converted output voltage

Min.: 0 V

Max.: 79.998 V

Displays the converted output voltage of the yaw and acceleration sensor

  • 2.31 V to 2.69 V: Vehicle on level ground
  • 1.88 V to 2.5 V: Deceleration
  • 2.5 V to 3.11 V: Acceleration
  • Fixed at 1.87 V: G sensor malfunction
  • Fixed at 1.87 V: Communication malfunction

-

Lock Up

Lock-up

OFF or ON

  • ON: Lock-up engaged
  • OFF: Lock-up disengaged

-

Shift Status

Gear shift commanded by ECM

1st, 2nd, 3rd, 4th or 5th

Same as the gear actually engaged

*4

Solenoid (SLS)

SLS shift solenoid valve status

OFF or ON

  • ON: After engine start
  • OFF: Ignition switch in ON position

-

SLU Solenoid Status

SLU shift solenoid valve status

OFF or ON

  • ON: Lock-up engaged
  • OFF: Lock-up disengaged

-

SL Solenoid Status

SL shift solenoid valve status

OFF or ON

  • ON: Lock-up permitted
  • OFF: Lock-up not permitted

-

Solenoid(SC)

SC shift solenoid valve status

OFF or ON

  • ON: 1 second after shift lever moved from P to D or R, or from N to D or R
  • ON: From lock-up ON to OFF
  • OFF: Engine idling

-

Solenoid(SLP)

SLP shift solenoid valve status

OFF or ON

  • ON: After engine start
  • OFF: Ignition switch in ON position

-

G Sensor Calibration

G sensor calibration status

Incomplete or Complete

Complete

-

G Sensor Learning Value

G sensor learned value voltage

Min.: 0 V

Max.: 79.998 V

2.31 to 2.69 V: G sensor calibration complete

-

CVT Oil Press Calibration

CVT oil pressure calibration status

Incompl or Compl

Compl

-

  • *1: With fuel vapor absorber pump module
  • *2: Without fuel vapor absorber pump module

HINT:

  • *3: Refer to DTC P0705.

    Click here

  • *4: "Shift Status" is a signal divided into 5 gears for the Active Test.

    It does not indicate gear ratios during normal driving conditions, nor gears engaged during 7-speed sequential shift mode.

ACTIVE TEST

HINT:

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Warm up the engine.

(b) Turn the ignition switch OFF.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to the ON position.

(e) Turn on the Techstream.

(f) Select the following menu items: Powertrain / Engine and ECT / Active Test.

(g) Perform the Active Test by following the instructions on the Techstream.

Powertrain > Engine and ECT > Active Test

Tester display

Item

Control Range

Diagnostic Note

Connect the TC and TE1

Turn the connection between terminals TC and TE1 on and off

ON or OFF

  • ON: Terminals TC and TE1 are connected.
  • OFF: Terminals TC and TE1 are disconnected.

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P position.

Activate the Solenoid (SLU)

Operate the SLU shift solenoid valve

ON or OFF

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P or N position.

Activate the Lock Up

Activates the lock-up

ON or OFF

Used to check lock-up operation.

Perform the "Activate the Lock Up" procedure while monitoring engine speed and the SPD (NT) item.

(Vehicle Condition)

Perform when vehicle speed is 60 km/h or more.

Activate the Solenoid (SL)

Operate the SL shift solenoid valve

ON or OFF

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P or N position.

Control the Shift Position

Operates the shift solenoid valves to allow manual selection of the gear ratio (1st - 2nd - 3rd - 4th - 5th)

Reference gear ratios:

1st (gear ratio 2.48 max.) - 2nd (1.46) - 3rd (1.0) - 4th (0.7) - 5th (gear ratio 0.4 min.)

  • Press the "→" key: Shift up
  • Press the "←" key: Shift down

Used to check the operation of the shift solenoid valves.

NOTICE:

Performing this test at a speed other than those specified in the "Vehicle Condition" column will damage the transaxle.

HINT:

Perform "Control the Shift Position" while checking "Shift Status" to confirm the actual engaged gear.

(Vehicle Condition)

Perform at a vehicle speed between 20 km/h and 45 km/h.

Control the SLS Pressure

Activate the SLS shift solenoid

High or low

(Vehicle Condition)

Perform with the ignition switch ON and the engine running.

Activate the Solenoid (SLS)

Activate the SLS shift solenoid

ON or OFF

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P or N position.

Activate the Solenoid(SC)

Activate the SC shift solenoid

ON or OFF

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P or N position.

Activate the Solenoid(SLP)

Activate the SLP shift solenoid

ON or OFF

(Vehicle Condition)

Perform with the ignition switch ON, engine off and shift lever in P or N position.