K114 Continuously Variable Transmission

Acceleration Sensor Malfunction (P1586)

3steps
~18min
2/5difficulty
Done 0 of 3

DESCRIPTION

The ECM determines the vehicle inclination based on a signal transmitted by the airbag sensor assembly (yaw and acceleration sensor). If a malfunction is detected in the airbag sensor assembly (yaw and acceleration sensor) based on a malfunction signal transmitted by the skid control ECU (brake actuator assembly), the ECM stores this DTC.

HINT:

  • The airbag sensor assembly (yaw and acceleration sensor) signal is transmitted to the skid control ECU (brake actuator assembly) via CAN communication.
  • If other CAN communication DTCs are output, begin troubleshooting with those DTCs.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

MIL

Memory

P1586

Acceleration sensor malfunction

After the ignition switch is turned ON, the skid control ECU (brake actuator assembly) detects one of the following conditions, and the ECM receives a diagnostic signal transmitted by the skid control ECU (brake actuator assembly) for at least 3 seconds (1 trip detection logic).

  • When the vehicle is driven at 30 km/h or more, the difference between the longitudinal G value calculated from the airbag sensor assembly (yaw and acceleration sensor) (G sensor) and the value based on vehicle speed exceeds 0.35 G for at least 60 seconds.
  • The signal from the airbag sensor assembly (yaw and acceleration sensor) does not change more than 16 times while the vehicle speed decreases from 30 km/h to 0 km/h.
  • Airbag sensor assembly (yaw and acceleration sensor)
  • Brake actuator assembly (skid control ECU)
  • CAN communication system

Not activated

DTC recorded

DTC Detection Condition Sequence:

Vehicle Operating Conditions

Sequence 1

Sequence 2

Diagnostic Condition

The ignition switch is in the ON position.

○

○

Malfunction condition

When the vehicle is driven at a speed of 30 km/h or more, the difference between the longitudinal G value calculated from the airbag ECU assembly (yaw and acceleration sensor) (G sensor) and the longitudinal G value calculated from vehicle speed exceeds 0.35 G for 60 seconds or more.

○

-

The signal from the airbag sensor assembly (yaw and acceleration sensor) does not change more than 16 times while the vehicle speed decreases from 30 km/h to 0 km/h.

-

○

Duration

3 seconds minimum

3 seconds minimum

Detection logic

1 trip detection logic

1 trip detection logic

HINT:

This DTC is stored when one of the above detection sequences is met.

WIRING DIAGRAM

Refer to DTC P1585

Click here

PRECAUTION / NOTICE / HINT

NOTICE:

  • Perform initialization after replacing any part related to the CVT system.

    Click here

  • Make sure no DTCs are stored after performing initialization.

    Click here

HINT:

After completing the repair, clear the DTCs and perform the following procedure to confirm that the DTCs are not output.

  1. Drive the vehicle at 30 km/h or more for 60 seconds or more.
  2. While driving the vehicle at 30 km/h, depress the brake pedal 16 times or more until the vehicle stops.
  3. Check whether any other DTCs are output.

    Click here

PROCEDURE

  1. CHECK WHETHER DTCs ARE OUTPUT

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Check the DTCs.

Powertrain > Engine and ECT > Trouble Codes

Result:

Result

Proceed to

DTC U0129 is not output

A

DTC U0129 is output

B

B

GO TO CAN COMMUNICATION SYSTEM

A
  1. CHECK FOR DTC OUTPUT (IN ADDITION TO DTC P1586)

(a) Connect the Techstream to the DLC3.

(b) Turn the Techstream on.

(c) Turn the ignition switch to ON.

(d) Clear the DTCs.

Click here

Powertrain > Engine and ECT > Clear DTCs

(e) Perform a road test driving the vehicle at 30 km/h or more, apply the brakes at least 16 times and finally stop the vehicle.

(f) Select the following menu items: Powertrain / Engine and ECT / Trouble Codes.

Powertrain > Engine and ECT > Trouble Codes

(g) Read the DTCs using the Techstream.

HINT:

If DTCs other than P1586 are output, troubleshoot those DTCs first.

Result:

Result

Proceed to

Only DTC P1586 is output

A

DTC P1586 and other DTCs are output

B

B

GO TO DTC CHART

A
  1. READ VALUE USING TECHSTREAM (G SENSOR)

(a) Connect the Techstream to the DLC3.

(b) Turn the ignition switch to ON.

(c) Turn on the Techstream.

(d) Select the following menus: Powertrain / Engine and ECT / Data List.

Powertrain > Engine and ECT > Data List

G Sensor

(e) Depending on the Techstream display, record the Data List.

Powertrain > Engine and ECT > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

G Sensor

Yaw and acceleration sensor converted output voltage

Min.: 0 V

Max.: 79.998 V

Displays the converted output voltage of the yaw and acceleration sensor

  • 2.31 V to 2.69 V: Vehicle on level ground
  • 1.88 V to 2.5 V: Deceleration
  • 2.5 V to 3.11 V: Acceleration
  • Fixed at 1.87 V: G sensor malfunction
  • Fixed at 1.87 V: Communication malfunction

-

Result:

Result

Proceed to

The displayed data is not within the range shown under "Normal Condition".

A

The displayed data is within the range shown under "Normal Condition".

B

B

REPLACE BRAKE ACTUATOR ASSEMBLY

A
  1. REPLACE AIRBAG SENSOR ASSEMBLY

(a) Replace the airbag sensor assembly (yaw and acceleration sensor).

Click here

NEXT

PERFORM INITIALIZATION