K114 Continuously Variable Transmission

Road Test

5steps
~30min
2/5difficulty
Done 0 of 5

ROAD TEST

CONFIRM PROBLEM SYMPTOMS

(a) Try to reproduce the symptoms based on the analysis of the customer's complaint. If the problem is that the transaxle does not change gear ratio, or shifts at the wrong engine speed, perform the road test below, referring to the shift pattern table and trying to reproduce the symptoms of the problem.

ROAD TEST

CAUTION:

During the road test, strictly observe all speed limits, traffic laws and the precautions required for the road conditions.

NOTICE:

  • Perform this test only after verifying and confirming that the engine is operating normally.
  • Perform this test when the CVT fluid temperature is between 50 and 100 °C.
  • Perform this test with the A/C switched off.

HINT:

  • The lock-up control does not operate when the CVT fluid temperature is 40 °C or less and the vehicle speed is 60 km/h or less, or when the CVT fluid temperature is 5 °C or less.
  • The lock-up control does not operate when the engine coolant temperature is 35 °C or less.
  • The lock-up vehicle speed may vary depending on the electrical load, the air conditioning and the brake operation.
  • Keep the accelerator pedal angle constant to maintain the specified vehicle speed.
  • Fully depress the accelerator pedal and raise the engine speed immediately after the pedal is fully depressed.

Shift pattern table (with fuel vapor pump absorber module):

NORMAL mode with ON position:

Shift lever position

Accelerator pedal position

(vehicle speed)

Fully depressed

(Before 1st upshift)

*1

Fully depressed

(Before 2nd upshift)

*2

Constant position

(100 km/h)

*3

Constant position

(40 km/h)

*4

Constant position

(70 km/h)

*5

Fully depressed

(when accelerating at 70 km/h)

*6

D

(NORMAL mode, ignition ON)

5,800 to 6,600 rpm

5,800 to 6,600 rpm

1,500 to 2,000 rpm

800 to 1,300 rpm

1,000 to 1,500 rpm

3,000 rpm minimum

SPORT mode with ON position:

Shift lever position

Accelerator pedal position

(vehicle speed)

Fully depressed

(Before 1st upshift)

*1

Fully depressed

(Before 2nd upshift)

*2

Constant position

(100 km/h)

*3

Constant position

(40 km/h)

*4

Constant position

(70 km/h)

*5

Fully depressed

(when accelerating at 70 km/h)

*6

D

(SPORT mode, ignition ON)

5,900 to 6,600 rpm

5,900 to 6,600 rpm

2,000 to 2,500 rpm

1,000 to 1,500 rpm

1,500 to 2,000 rpm

3,000 rpm minimum

Shift pattern table (without fuel vapor pump absorber module):

NORMAL mode with ON position:

Shift lever position

Accelerator pedal position

(vehicle speed)

Fully depressed

(Before 1st upshift)

*1

Fully depressed

(Before 2nd upshift)

*2

Constant position

(100 km/h)

*3

Constant position

(40 km/h)

*4

Constant position

(70 km/h)

*5

Fully depressed

(when accelerating at 70 km/h)

*6

D

(NORMAL mode, ignition ON)

5,800 to 6,600 rpm

5,800 to 6,600 rpm

1,700 to 2,200 rpm

800 to 1,300 rpm

1,100 to 1,600 rpm

3,000 rpm minimum

SPORT mode with ON position:

Shift lever position

Accelerator pedal position

(vehicle speed)

Fully depressed

(Before 1st upshift)

*1

Fully depressed

(Before 2nd upshift)

*2

Constant position

(100 km/h)

*3

Constant position

(40 km/h)

*4

Constant position

(70 km/h)

*5

Fully depressed

(when accelerating at 70 km/h)

*6

D

(SPORT mode, ignition ON)

5,900 to 6,700 rpm

5,900 to 6,700 rpm

2,200 to 2,700 rpm

1,000 to 1,500 rpm

1,700 to 2,100 rpm

3,000 rpm minimum

Lock-up Program

Shift lever position

Lock-up condition

(Accelerator pedal opening angle)

Lock-up ON

(10 %)

Lock-up OFF

(0 %)

D

(NORMAL mode, ignition ON)

15 à 30 km/h

(9 to 19 mph)

5 à 25 km/h

(3 to 16 mph)

D

(SPORT mode, ignition ON)

10 à 25 km/h

(6 to 16 mph)

HINT:

  • Lock-up OFF by the lock-up control can be confirmed when the lock-up ON conditions change to the lock-up OFF conditions as shown in the following table.
  • The flexible lock-up control condition cannot be checked by viewing the "Lock up" item in the data list. Confirm the lock-up condition by checking the operation of shift solenoid valve SC and shift solenoid valve SL.

Lock-up ON condition:

Lock-up OFF condition:

Shift solenoid valve SC: OFF

Shift solenoid valve SC: ON

Shift solenoid valve SL: ON

Shift solenoid valve SL: ON (no change)

(a) Test in D position

Place the shift lever in the D position and check the following points:

(1) Check whether the gear ratio changes during normal driving (average driving in urban areas).

  1. With the vehicle stopped, fully depress the accelerator pedal and check the engine speed at the shift points indicated by *1 and *2 in the shift pattern table.
  2. With the vehicle stopped, depress the accelerator pedal to a constant intermediate position and check the engine speed when the vehicle reaches the speed indicated by *3 in the shift pattern table.
  3. Release the accelerator pedal and check the engine speed when the vehicle decelerates to the speed indicated by *4 in the shift pattern table.
  4. Depress the accelerator pedal again to a constant intermediate position and check the engine speed when the vehicle reaches the speed indicated by *5 in the shift pattern table.
  5. Fully depress the accelerator pedal and check the engine speed when the vehicle accelerates from the speed indicated by *6 in the shift pattern table.

(2) Check for abnormal noises and abnormal vibrations.

HINT:

Locate the source of any abnormal noise or vibration, as it may also come from differential imbalance, the torque converter clutch, etc.

(3) Check for abnormal shocks or slipping during forced downshifts.

(4) Check the lock-up mechanism.

(b) Test in M position

Place the shift lever in the M position and check the following points:

(1) Check the shift operation.

  • When driving with M7 selected (vehicle traveling at approximately 90 to 100 km/h), check the engine braking effect in M6 when the shift lever is moved to the "-" position.
  • When driving with M6 selected (vehicle traveling at approximately 70 to 80 km/h), check the engine braking effect in M5 when the shift lever is moved to the "-" position.
  • When driving with M5 selected (vehicle traveling at approximately 50 to 60 km/h), check the engine braking effect in M4 when the shift lever is moved to the "-" position.
  • When driving with M4 selected (vehicle traveling at approximately 40 to 50 km/h), check the engine braking effect in M3 when the shift lever is moved to the "-" position.
  • When driving with M3 selected (vehicle traveling at approximately 30 to 40 km/h), check the engine braking effect in M2 when the shift lever is moved to the "-" position.
  • While driving the vehicle with M2 selected (vehicle speed approximately 20 to 30 km/h), check the engine braking effectiveness in M1 when the shift lever is moved to the "-" position.

(c) R Position Test

Move the shift lever to the R position and lightly depress the accelerator pedal. Make sure the vehicle moves in reverse without any abnormal noise or abnormal vibration.

(d) P Position Test

Stop the vehicle on a slope (more than 5°). Then move the shift lever to the P position and release the parking brake. Check that the parking lock pawl prevents the vehicle from moving.