Diagnostic System
DIAGNOSTIC SYSTEM
OBD-II (with fuel vapor absorber pump module)
(a) When troubleshooting a vehicle equipped with OBD II (On-Board Diagnostics), connect the OBD II scan tool (complying with SAE J1978) to the vehicle's DLC3 (Data Link Connector 3). This allows various data to be read from the vehicle's ECM (Engine Control Module).
(b) OBD II regulations require the vehicle's on-board computer to illuminate the MIL (Malfunction Indicator Lamp) on the instrument panel when the computer detects a malfunction in:
(1) Emission control system components.
(2) Powertrain control components (that affect emissions).
(3) The computer itself.
In addition, the corresponding DTCs prescribed by SAE J2012 are stored in the ECM memory. If the malfunction does not recur after 3 consecutive driving cycles, the MIL turns off automatically, but the DTCs remain stored in the ECM memory.
(c) To check the DTCs, connect the Techstream to the DLC3. The Techstream displays the DTCs, freeze frame data and various other engine data. The DTCs and freeze frame data can be cleared using the Techstream. To improve the OBD function on vehicles and to develop the off-board diagnostic system, a Controller Area Network (CAN) communication system is introduced. CAN is a network that uses a pair of data transmission lines to connect multiple computers and sensors. It enables high-speed communication between systems and simplifies wiring harness connections.
Click here![]()
EURO-OBD (without fuel vapor absorber pump module)
(a) When troubleshooting vehicles equipped with the European On-Board Diagnostic (Euro-OBD) system, connect the OBD scan tool (conforming to ISO 15765-4). This allows reading of various data output by the vehicle's ECM.
(b) Euro-OBD regulations require the on-board computer to illuminate the malfunction indicator light (MIL) on the instrument panel if any of the following malfunctions occur:
(1) The emission control system or its components
(2) Components of the powertrain control system (that affect emissions)
(3) The computer itself
In addition, the corresponding diagnostic trouble codes (DTCs) prescribed by ISO 15765-4 are stored in the ECM memory.
If the malfunction does not recur after 3 consecutive trips, the MIL turns off automatically, but the DTCs remain stored in the ECM memory.
(c) To check DTCs, connect the Techstream or OBD scan tool to the vehicle's data link connector 3 (DLC3). The scan tool displays DTCs, freeze frame data and various engine data.
DTCs and freeze frame data can be erased using the scan tool.
Click here![]()
NORMAL MODE AND CHECK MODE
(a) Techstream only:
The diagnostic system operates in normal mode during normal vehicle use. Normal mode uses 2-trip detection logic to ensure accurate detection of malfunctions. Check mode is available as an option for technicians. In check mode, 1-trip detection logic is used to reproduce malfunction symptoms and increase the system's ability to detect malfunctions, including intermittent problems.
2-TRIP DETECTION LOGIC
(a) When a malfunction is detected for the first time, it is temporarily stored in the ECM memory (1st trip). If the same malfunction is detected again during the next driving cycle, the MIL illuminates (2nd trip).
FREEZE FRAME DATA
(a) The ECM records vehicle and driving condition information as freeze frame data at the moment a DTC is stored. When troubleshooting, freeze frame data can help determine whether the vehicle was moving or not, whether the engine was warmed up or not, whether the air-fuel ratio was lean or rich, and it can help check other data at the time of a malfunction.
(b) Techstream displays freeze frame data at five different points: 1) three times before the DTC is stored, 2) once when the DTC is stored, and 3) once after the DTC is stored. This data can be used to reproduce the vehicle operating conditions when the malfunction occurred. This data can help determine the cause of the malfunction. It can also help determine whether a DTC is due to a temporary malfunction.
FREEZE FRAME DATA LIST
Powertrain > Engine and ECTTester display |
|---|
Vehicle Speed |
Engine Speed |
Calculate Load |
MAF |
Coolant Temp |
Throttle Motor DUTY |
N Range Status |
Starter Signal |
Neutral Position SW Signal |
Stop Light Switch |
A/C Signal |
Closed Throttle Position SW |
TC and TE1 |
SPD (NT) |
Shift SW Status (P Range) |
Pattern Switch (PWR/M) |
Shift SW Status (R Range) |
Shift SW Status (N Range) |
Shift SW Status (N,P Range) Supported |
Shift SW Status (N,P Range) |
Sports Shift Up SW |
Sports Shift Down SW |
Sports Mode Selection SW |
Shift SW Status (D Range) |
A/T Oil Temperature 1 |
ATF Thermal Degradation Estimate |
NT Sensor Voltage |
SPD (NIN) |
SPD (NOUT) |
NOUT Sensor Voltage |
A/T Oil Pressure |
G Sensor |
Lock Up |
Shift Status |
Solenoid (SLS) |
SLU Solenoid Status |
SL Solenoid Status |
Solenoid(SC) |
Solenoid(SLP) |
G Sensor Calibration |
G Sensor Learning Value |
CVT Oil Press Calibration |
CHECK DATA LINK CONNECTOR 3 (DLC3)
(a) Check DLC3.
Click here![]()
CHECK BATTERY VOLTAGE
Standard voltage:
11 à 14 V
If the voltage is below 11 V, replace or recharge the battery before proceeding to the next step.
MIL (Malfunction Indicator Lamp)
(a) Check that the MIL illuminates when the ignition switch is turned to ON.
If the MIL does not illuminate, there is a problem in the MIL circuit.
- with fuel vapor absorber pump module:
Click here
.gif)
- without fuel vapor absorber pump module:
Click here
.gif)
(b) When the engine starts, the MIL turns off.