Tire Pressure Monitoring

Initialization Switch (Test Mode DTC) (C2198/98)

~3min read

DESCRIPTION

The switch circuit inside the combination meter assembly turns on and off in response to operation of the steering switch assembly.

In test mode, when the steering switch assembly is operated, "TPMS" is selected on the multi-information display and the "ENTER" switch (steering switch assembly) is pressed, the tire pressure warning light comes on. When the "ENTER" switch (steering switch assembly) is not pressed, the tire pressure warning light flashes at 0.125-second intervals.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

C2198/98

Initialization Switch (Test Mode DTC)

The test mode procedure is complete.

  • Steering pad switch assembly
  • Spiral Cable Sub-assembly
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

-

WIRING DIAGRAM

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU and receiver, record the IDs stored in the ECU using the Techstream and note them down before removal.

    Click here

  • Initialization must be performedafter registeringthe transmitter IDs in the tire pressure ECU if the ECU and/or any of the valves and transmitters have been replaced.

PROCEDURE

  1. CHECK STEERING PAD SWITCH ASSEMBLY

(a) Remove the steering pad switch assembly.

Click here

(b) Check the steering pad switch assembly.

Click here

NG

REPLACE STEERING PAD SWITCH ASSEMBLY

OK
  1. CHECK SPIRAL CABLE SUB-ASSEMBLY

(a) Remove the spiral cable sub-assembly.

Click here

(b) Inspect the spiral cable sub-assembly.

Click here

NG

REPLACE SPIRAL CABLE SUB-ASSEMBLY

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (SPIRAL CABLE SUB-ASSEMBLY - COMBINATION METER ASSEMBLY)

(a) Disconnect connector F29 from the spiral cable sub-assembly.

(b) Disconnect the combination meter assembly connector F4.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

F29-10 (+DP) - F4-28 (MSM+)

Always

Below 1 Ω

F29-10 (+DP) or F4-28 (MSM+) - Body ground

Always

10 kΩ minimum

F29-11 (+DP2) - F4-33 (MSSL)

Always

Below 1 Ω

F29-11 (+DP2) or F4-33 (MSSL) - Body ground

Always

10 kΩ minimum

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK WIRE HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - TIRE PRESSURE ECU AND RECEIVER)

(a) Disconnect the M23 tire pressure ECU and receiver connector.

(b) Disconnect the combination meter assembly connector F4.

(c) Measure the resistance according to the value(s) in the table below.

Standard resistance:

Tester Connection

Condition

Specified Condition

M23-3 (CLSW) - F4-4 (INT)

Always

Below 1 Ω

M23-3 (CLSW) or F4-4 (INT) - Body ground

Always

10 kΩ minimum

F4-21 (ET) - Body Ground

Always

Below 1 Ω

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

OK
  1. CHECK VOLTAGE OF TERMINAL (INT)

(a) Disconnect the connector from the combination meter assembly F4.

(b) Measure the voltage according to the value(s) in the table below.

Standard voltage:

Tester Connection

Condition

Specified Condition

F4-4 (INT) - Body Ground

Ignition Switch in ON position

8 à 15 V

OK

GO TO METER/GAUGE SYSTEM

NG

REPLACE TIRE PRESSURE ECU AND RECEIVER