Tire Pressure Monitoring

Initialization

~5min read

INITIALIZATION

NOTICE:

  • Initialization can be confirmed using the tire pressure warning light.
  • If the ignition switch is in the OFF position during initialization, the tire pressure detection ECU and receiver record that initialization has been performed. Therefore, it is not necessary to perform the initialization procedure again after turning the ignition switch ON.
  • The order in which data is received is random.
  • If signals from all tire pressure valves and transmitters are received, initialization is complete.
  • Initialization is complete when the Data List screen "ID Tire Inflation Pressure" displays the correct pressures.

    Click here

  • Initialization is normally completed after a few minutes. However, the tire pressure display function may take at least 10 minutes to display the tire pressures.
  • It may take a few minutes for the values to be displayed. If the values are not displayed after a few minutes, troubleshoot using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).

    Click here

  • If initialization has not been completed successfully, DTC C2177/77 is stored after vehicle speed is detected at at least 40 km/h for at least 20 minutes.
  • During test mode (sensor check mode), the system will not enter initialization mode even if the tire pressure warning reset switch is pressed.
  • Initialization can be completed by connecting terminals 13 (TC) and 4 (CG) of the data link connector 3.

    *a

    Front view of DLC3

BEFORE INITIALIZATION

(a) Adjust the tire pressure to the specified value.

HINT:

Refer to the link because the tire pressure adjustment procedure varies depending on the tire temperature.

Click here

HINT:

The tire pressure monitoring system turns on the low tire pressure warning light to warn the driver when the following condition is met:

  • When the steering wheel switch assembly is operated, the tire pressure decreases to approximately 75% or less of the tire pressure setting at the time of system initialization.

INITIALIZATION PROCEDURE

(a) Turn the ignition switch to ON.

(b) Operate the steering wheel switch assembly, select "TPMS" on the multi-information display and press and hold the "ENTER" switch (steering wheel switch assembly) until the tire pressure warning light flashes 3 times.

*1

Low tire pressure warning light

*2

"ENTER" switch (steering wheel switch assembly)

*a

Tire pressure warning light flashing sequence

*b

1 s

*c

ON

*d

OFF

(c) Turn the ignition switch to OFF.

(d) Connect the Techstream to the DLC3.

(e) Turn the ignition switch ON and turn on the Techstream.

(f) Select the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID 1 Tire Inflation Pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 2 Tire Inflation Pressure

Tire Inflation Pressure ID2

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 3 Tire Inflation Pressure

Tire Inflation Pressure ID3

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 4 Tire Inflation Pressure

Tire Inflation Pressure ID4

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 5 Tire Inflation Pressure

Tire Inflation Pressure ID5

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

  • If N/A is displayed, data has not been received.*1
  • *2

HINT:

  • *1: It may take a few minutes for the values to be displayed. If the values are not displayed after a few minutes, perform troubleshooting using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).

    Click here

  • *2: With conventional spare tire

(g) Confirm that initialization is complete.

(h) Check whether the tire pressure data for all wheels is displayed on the Techstream screen.