Tire Pressure Monitoring

Registration

~6min read

REGISTRATION

PROCEDURE

1. BEFORE REGISTRATION

NOTICE:

The transmitter ID is printed on the tire pressure valve and the transmitter. The transmitter ID cannot be read after the tire is mounted on the wheel. Therefore, record the transmitter ID before mounting the tire.

(a) When replacing the tire pressure warning ECU and receiver:

(1) Using the Techstream, read the transmitter IDs registered in the old ECU and record them.

(2) If the registered transmitter IDs cannot be read due to faulty components such as the tire pressure warning ECU and receiver, remove the tires from the wheels and check the IDs printed on the tire pressure valves and transmitters.

(b) When replacing the tire pressure valves and transmitters:

(1) Record the 7-digit number (transmitter ID) printed on the tire pressure valve and transmitter.

*1

Tire pressure valve and transmitter

-

-

*a

Transmitter ID (7-digit number)

-

-

2. REGISTER TRANSMITTER ID (using the Techstream)

HINT:

  • Previously registered IDs will be erased from memory once registration is complete.
  • If the ID registration step is not completed within 300 seconds, ID registration is cancelled.

(a) Adjust the tire pressure to the specified value.

Click here

(b) Turn the ignition switch OFF.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to ON and turn on the Techstream.

(e) Select the following menus: Chassis / Tire Pressure Monitor / Utility / ID Registration.

Chassis > Tire Pressure Monitor > Utility

ID Registration

(f) Perform the procedure displayed on the Techstream.

3. CONFIRM TRANSMITTER ID REGISTRATION

NOTICE:

  • It may take a few minutes for the values to be displayed. If the values are not displayed after a few minutes, troubleshoot using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).

    Click here

  • If the transmitter IDs have not been registered, DTC C2171/71 is stored in the tire pressure warning ECU and receiver after at least 3 minutes.
  • If the displayed pressure values are normal, the transmitter IDs have been registered correctly.
  • If the tire pressure values are not displayed after a few minutes, the transmitter IDs may be incorrect or there may be a system malfunction.
  • Once all transmitter IDs are registered, DTC C2126/26 is stored in the tire pressure warning ECU and receiver, and the low tire pressure warning light flashes for 1 minute and then stays on. When the tire pressure warning ECU and receiver successfully receive signals from all transmitters whose IDs are registered in the ECU, DTC C2126/26 is cleared and the low tire pressure warning light turns off.

(a) Select the following menus: Chassis / Tire Pressure Monitor / Data List.

Chassis > Tire Pressure Monitor > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID 1 Tire Inflation Pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 2 Tire Inflation Pressure

Tire Inflation Pressure ID2

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 3 Tire Inflation Pressure

Tire Inflation Pressure ID3

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 4 Tire Inflation Pressure

Tire Inflation Pressure ID4

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 5 Tire Inflation Pressure

Tire Inflation Pressure ID5

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

  • If N/A is displayed, data has not been received.*1
  • *2

HINT:

  • *1: It may take a few minutes for the values to be displayed. If the values are not displayed after a few minutes, perform troubleshooting using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).
  • *2: With conventional spare tire
  • The wheel positions of ID1 to ID4 (ID5: With conventional spare tire) cannot be determined on the Data List.
Chassis > Tire Pressure Monitor > Data List

Tester display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

ID 5 Tire Inflation Pressure

(b) Reduce the tire inflation pressure of each tire by at least 40 kPa (0.4 kgf/cm2, 5.8 psi) and make sure the "ID Tire Inflation Pressure" data is updated and the actual tire inflation pressures are displayed.

(c) After confirming that all tire inflation pressure values (except the compact spare tire) have been updated, adjust the tire inflation pressure to the specified value, operate the steering wheel switch assembly, then perform initialization.