Tire Pressure Monitoring

Data List / Active Test

~9min read

DATA LIST / ACTIVE TEST

READ DATA LIST

HINT:

The Techstream Data List allows you to read the values or status of switches, sensors, actuators and other components without removing any parts. This non-intrusive check can be very useful, since intermittent conditions or signals can be identified before parts or wiring are moved. Reading the Data List during troubleshooting saves time in diagnosis.

NOTICE:

In the table below, the values listed under "Normal Condition" are reference values. Do not determine whether a part is faulty based only on these reference values.

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Tire Pressure Monitor / Data List.

(f) Read the Data List according to the Techstream display.

Chassis > Tire Pressure Monitor > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

Mode Status

Tire pressure monitor system mode

NORMAL or TEST

NORMAL: Normal mode

TEST: Test mode

-

Main Tire

Number of main tire IDs to register

4 or 5

4 to 5 displayed

  • 4 displayed: Without conventional spare tire
  • 5 displayed: With conventional spare tire

2nd Tire

Number of secondary tire IDs to register

4 or 5

4 to 5 displayed

  • 4 displayed: Without conventional spare tire
  • 5 displayed: With conventional spare tire

Initialization Switch

Tire Pressure Reset Switch

OFF or ON

OFF: "ENTER" switch (steering switch assembly) in OFF position

ON: Steering switch assembly operated, "TPMS" selected on the multi-information display, and "ENTER" switch (steering switch assembly) pressed and held in this position

-

Sensor ID Status

ID selection status

Main or 2nd

ID selection status

-

Initialization Switch Info

Low tire pressure reset switch setting information

WITHOUT or WITH

WITH

-

Sensor ID Switch Function

Information on whether the ID switching function is equipped

Without or With

Without: ID switching function is not equipped

With: ID switching function is equipped

-

Vehicle Speed

Vehicle speed value

min.: 0 km/h

max.: 255 km/h

Actual vehicle speed

Speed indicated by combination meter

Registered ID 1 Code

Registered ID1 Code

min.: 0

max.: FFFFFFF*1

Displays the registered ID number for transmitter ID1

-

Registered ID 2 Code

Registered ID2 Code

min.: 0

max.: FFFFFFF*1

Displays the registered ID number for transmitter ID2

-

Registered ID 3 Code

Registered ID3 Code

min.: 0

max.: FFFFFFF*1

Displays the registered ID number for transmitter ID3

-

Registered ID 4 Code

Registered ID4 Code

min.: 0

max.: FFFFFFF*1

Displays the registered ID number for transmitter ID4

-

Registered ID 5 Code

Registered ID5 Code

min.: 0

max.: FFFFFFF*1

Displays the registered ID number for transmitter ID5

*3

ID 1 Tire Inflation Pressure

ID 1 Tire Inflation Pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*2

ID 2 Tire Inflation Pressure

Tire Inflation Pressure ID2

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*2

ID 3 Tire Inflation Pressure

Tire Inflation Pressure ID3

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*2

ID 4 Tire Inflation Pressure

Tire Inflation Pressure ID4

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*2

ID 5 Tire Inflation Pressure

Tire Inflation Pressure ID5

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

  • If N/A is displayed, data has not been received.*2
  • *3

Threshold of Low-pressure (Lower Limit)

Tire inflation pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Displays the specified lower limit tire pressure warning threshold.

-

ID 1 Initial Threshold of Low-pressure

ID1 Initial Low-pressure Threshold

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Tire Pressure after Initialization

-

ID 2 Initial Threshold of Low-pressure

ID2 Initial Low-pressure Threshold

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Tire Pressure after Initialization

-

ID 3 Initial Threshold of Low-pressure

ID3 Initial Low-pressure Threshold

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Tire Pressure after Initialization

-

ID 4 Initial Threshold of Low-pressure

ID4 Initial Low-pressure Threshold

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Tire Pressure after Initialization

-

ID 5 Initial Threshold of Low-pressure

ID5 Initial Low-pressure Threshold

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Tire Pressure after Initialization

*3

ID 1 Temperature in Tire

ID1 Tire Temperature

min.: -40°C (-40°F)

max.: 215 °C

Actual tire temperature

If -40°C (-40°F) is displayed, data has not been received.

ID 2 Temperature in Tire

ID2 Tire Temperature

min.: -40°C (-40°F)

max.: 215 °C

Actual tire temperature

If -40°C (-40°F) is displayed, data has not been received.

ID 3 Temperature in Tire

ID3 Tire Temperature

min.: -40°C (-40°F)

max.: 215 °C

Actual tire temperature

If -40°C (-40°F) is displayed, data has not been received.

ID 4 Temperature in Tire

ID4 Tire Temperature

min.: -40°C (-40°F)

max.: 215 °C

Actual tire temperature

If -40°C (-40°F) is displayed, data has not been received.

ID 5 Temperature in Tire

ID5 Tire Temperature

min.: -40°C (-40°F)

max.: 215 °C

Actual tire temperature

  • If -40°C (-40°F) is displayed, data has not been received.
  • *3

Number of Trouble Code

Number of Registered DTCs

min.: 0

max.: 255

min.: 0

max.: -

-

HINT:

  • *1: Displayed only when the ID number is not registered.
  • *2: It may take several minutes for the values to be displayed. If the values are not displayed after several minutes, troubleshoot using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).

    Click here

  • *3: With conventional spare tire

PERFORM ACTIVE TEST

Using the Techstream to perform Active Tests allows relays, VSVs, actuators and other items to be operated without removing parts. This non-intrusive functional check can be very useful, because intermittent operation can be identified before parts or wiring are moved. Performing Active Tests at the start of troubleshooting saves time during diagnosis. Data List information can be displayed during Active Tests.

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Body Electrical / Combination Meter / Active Test.

(f) Perform the Active Test by following the instructions on the Techstream.

Body Electrical > Combination Meter > Active Test

Tester display

Item

Control Range

Diagnostic Note

Tire Pressure Warning System Indicator

Low tire pressure warning light

OFF or ON

Perform the test with the vehicle stationary and the engine idling.