Tire Pressure Monitoring

Transmitter ID1 Malfunction (C2141/41-C2145/45)

~13min read

DESCRIPTION

The tire pressure valve and transmitters installed in the tire and wheel assemblies measure the tire pressure. The measured values are transmitted by radio waves to the tire pressure warning ECU and the receiver inside the vehicle. The ECU compares the measured tire pressure values with the tire pressure threshold. When the measured tire pressure is lower than this threshold, the warning light in the combination meter assembly illuminates.

When the internal circuit of the tire pressure valve and transmitter is malfunctioning, one of these DTCs is output.

DTC No.

Detection Item

DTC Detection Condition

Suspected Area

Note

C2141/41

Transmitter ID1 Error

If an "ERROR" signal is received 3 times in a row, the tire pressure valve and transmitter are considered malfunctioning and this DTC is output.

This will occur when the tire inflation pressure is outside the specified range of -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range of -40 to 215 °C, or a malfunction occurs in the tire pressure valve and transmitter.

  • Tire pressure valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2142/42

Transmitter ID2 Error

If an "ERROR" signal is received 3 times in a row, the tire pressure valve and transmitter are considered malfunctioning and this DTC is output.

This will occur when the tire inflation pressure is outside the specified range of -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range of -40 to 215 °C, or a malfunction occurs in the tire pressure valve and transmitter.

  • Tire pressure valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2143/43

Transmitter ID3 Error

If an "ERROR" signal is received 3 times in a row, the tire pressure valve and transmitter are considered malfunctioning and this DTC is output.

This will occur when the tire inflation pressure is outside the specified range of -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range of -40 to 215 °C, or a malfunction occurs in the tire pressure valve and transmitter.

  • Tire pressure valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2144/44

Transmitter ID4 Error

If an "ERROR" signal is received 3 times in a row, the tire pressure valve and transmitter are considered malfunctioning and this DTC is output.

This will occur when the tire inflation pressure is outside the specified range of -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range of -40 to 215 °C, or a malfunction occurs in the tire pressure valve and transmitter.

  • Tire pressure valve and transmitter
  • Tire pressure warning ECU and receiver

-

C2145/45

Transmitter ID5 Error

If an "ERROR" signal is received 3 times in a row, the tire pressure valve and transmitter are considered malfunctioning and this DTC is output.

This will occur when the tire inflation pressure is outside the specified range of -50 to 380 kPa (-0.5 to 3.9 kgf/cm2, -7 to 55 psi), the temperature inside the tire is outside the specified range of -40 to 215 °C, or a malfunction occurs in the tire pressure valve and transmitter.

  • Tire pressure valve and transmitter
  • Tire pressure warning ECU and receiver

With conventional spare tire

HINT:

Perform the procedure to identify the malfunctioning tire pressure valve and transmitter, as this cannot be identified by the output of a DTC.

PRECAUTION / NOTICE / HINT

NOTICE:

  • When replacing the tire pressure warning ECU and receiver, record the IDs stored in the ECU using the Techstream and note them down before removal.

    Click here

  • Initialization must be performedafter registeringthe transmitter IDs in the tire pressure ECU if the ECU and/or any of the valves and transmitters have been replaced.

PROCEDURE

  1. IDENTIFY THE TRANSMITTER CORRESPONDING TO THE DTC

(a) Adjust the tire pressure to the specified values.

Click here

(b) Turn the ignition switch OFF.

(c) Connect the Techstream to the DLC3.

(d) Turn the ignition switch to the ON position.

(e) Turn on the Techstream.

(f) Select the following menus: Chassis / Tire Pressure Monitor / Data List.

(g) Display the "ID Tire Inflation Pressure" value for each wheel using the Techstream.

(h) Quickly reduce the tire pressure of each wheel to at least 40 kPa (0.4 kgf/cm2, 5.8 psi) within 30 seconds. If the "ID Tire Inflation Pressure" value displayed on the Techstream does not change, the tire pressure valve and transmitter corresponding to the unchanged "ID Tire Inflation Pressure" value caused the DTC to be output.

HINT:

  • Identify the malfunctioning tire pressure valve and transmitter by reducing the pressure of each tire several times.
  • Record the "ID Tire Inflation Pressure" value for each tire.
Chassis > Tire Pressure Monitor > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID 1 Tire Inflation Pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 2 Tire Inflation Pressure

Tire Inflation Pressure ID2

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 3 Tire Inflation Pressure

Tire Inflation Pressure ID3

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 4 Tire Inflation Pressure

Tire Inflation Pressure ID4

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 5 Tire Inflation Pressure

Tire Inflation Pressure ID5

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

  • If N/A is displayed, data has not been received.*1
  • *2

HINT:

  • *1: It may take a few minutes for the values to be displayed. If the values are not displayed after a few minutes, perform troubleshooting using the inspection procedure for DTCs C2121/21 to C2124/24 (C2125/25: With conventional spare tire).

    Click here

  • *2: With conventional spare tire
Chassis > Tire Pressure Monitor > Data List

Tester display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

ID 5 Tire Inflation Pressure

(i) Check the Data List.

NOTICE:

  • The display of tire pressure data updates may take a few minutes.
  • If an "ID Tire Inflation Pressure" value has not changed, adjust the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then quickly reduce the tire pressure and check the value again.
  • Record the transmitter ID corresponding to the "ID Tire Inflation Pressure" values of each tire.

(j) After confirming that the "ID Tire Inflation Pressure" values of a tire have changed, repeat this procedure for each tire. Identify the transmitter that corresponds to the DTC.

(k) When all "ID Tire Inflation Pressure" data (ID1 to ID4 (ID5: with conventional spare tire)) have changed, identify the defective tire pressure valve and transmitter using the registered ID numbers and the output DTCs.

Result:

Result

Proceed to

One or more transmitters are abnormal

A

All transmitters are normal

B

B

END

A
  1. REPLACE TIRE PRESSURE VALVE AND TRANSMITTER

(a) Replace the identified tire pressure valve and transmitter with new parts.

Click here

HINT:

  • Before installing new tire pressure valves and transmitters, record their transmitter IDs.
  • The IDs for the tire pressure valves and transmitters that are not replaced must be checked using Techstream and then registered.
NEXT
  1. TRANSMITTER ID REGISTRATION

(a) Perform the registration.

Click here

NEXT
  1. PERFORM INITIALIZATION

(a) Adjust the tire pressure to the specified value.

Click here

(b) Perform initialization.

Click here

NEXT
  1. CONFIRM TIRE PRESSURE (DATA LIST)

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON.

(d) Turn on the Techstream.

(e) Select the following menu items: Chassis / Tire Pressure Monitor / Data List.

(f) Check the values by referring to the table below.

Chassis > Tire Pressure Monitor > Data List

Tester display

Item

Range

Normal Condition

Diagnostic Note

ID 1 Tire Inflation Pressure

ID 1 Tire Inflation Pressure

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 2 Tire Inflation Pressure

Tire Inflation Pressure ID2

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 3 Tire Inflation Pressure

Tire Inflation Pressure ID3

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 4 Tire Inflation Pressure

Tire Inflation Pressure ID4

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

If N/A is displayed, data has not been received.*1

ID 5 Tire Inflation Pressure

Tire Inflation Pressure ID5

min.: Absolute pressure (abs) / 0 kPa (0 kgf/cm2, 0 lb/in2), gauge pressure / 0 kPa (0 kgf/cm2, 0 lb/in2)

max.: Absolute pressure (abs) / 480 kPa (4.9 kgf/cm2, 70 psi), gauge pressure / 380 kPa (3.9 kgf/cm2, 55 psi)

Actual Tire Inflation Pressure

  • If N/A is displayed, data has not been received.*1
  • *2

HINT:

  • *1: It may take a few minutes for the values to be displayed.
  • The wheel positions of ID1 to ID4 (ID5: With conventional spare tire) cannot be determined on the Data List.
  • If an "ID Tire Inflation Pressure" value has not changed, adjust the tire pressure to the appropriate specified value and rotate the tire 90 to 270 degrees. Then quickly reduce the tire pressure and check the value again.
  • *2: With conventional spare tire
Chassis > Tire Pressure Monitor > Data List

Tester display

ID 1 Tire Inflation Pressure

ID 2 Tire Inflation Pressure

ID 3 Tire Inflation Pressure

ID 4 Tire Inflation Pressure

ID 5 Tire Inflation Pressure

Result:

Result

Proceed to

Tire pressure values are not displayed.

A

All recorded tire pressure values are equal to the specified values.

B

A

REPLACE TIRE PRESSURE ECU AND RECEIVER

B

END