Tire Pressure Monitoring

Test Mode Procedure

~5min read

TEST MODE PROCEDURE

TEST MODE PROCEDURE (SIGNAL CHECK MODE)

HINT:

  • When entering test mode (signal check mode), the tire pressure detection ECU and receiver first output all DTCs for test mode (signal check mode).

    After the tire pressure detection ECU and receiver complete the signal check for each check item, the DTCs for systems considered normal are cleared.

    DTCs for other check items may not be cleared if only certain signals are checked.

  • When test mode (signal check mode) returns to normal mode, all test mode (signal check mode) DTCs will be cleared.
  • During test mode (signal check mode), the system is not initialized, even if the initialization procedure is performed.

(a) Turn the ignition switch OFF.

(b) Connect the Techstream to the DLC3.

(c) Turn the ignition switch to ON and turn on Techstream.

(d) Select the following menus: Chassis / Tire Pressure Monitor / Utility / Signal Check.

Chassis > Tire Pressure Monitor > Utility

Signal Check

HINT:

Each time the conditions for clearing test mode (signal check mode) DTCs are met, the tire pressure warning light turns on for 1 second. Then the tire pressure warning light flashes at 0.125 second intervals.

*a

0,125 s

*b

ON

*c

OFF

(e) Tire Pressure Warning Reset Switch Check (DTC C2198/98)

(1) Operate the steering wheel switch assembly, select "TPMS" on the multi-information display and press the "ENTER" switch (steering wheel switch assembly).

(f) Wait 1.5 minutes while the vehicle is stopped, or drive the vehicle at a speed of at least 50 km/h for 1 minute (DTCs C2181/81 to C2184/84 (C2185/85: With conventional spare tire))

HINT:

The tire pressure valves and transmitters send signals to the tire pressure detection ECU and receiver once every 1.5 minutes while the vehicle is stopped, and once every minute while the vehicle is being driven.

(g) Make sure the test mode DTCs of the tire pressure detection system (signal check mode) have been cleared.

Test mode (signal check mode) DTC

Test signal

Test mode (signal check mode) DTC clearing condition

*: With conventional spare tire

C2181/81 à C2184/84 (C2185/85*)

Transmitter Data

The data is from the transmitter whose ID is registered in the tire pressure warning ECU and receiver.

C2198/98

Tire Pressure Reset Switch Signal

A signal is received indicating that the steering pad switch assembly is operated, "TPMS" is selected on the multi-information display, and the "ENTER" switch (steering pad switch assembly) is pressed.

(h) Result

HINT:

After completing the signal check, check for test mode (signal check mode) DTCs to confirm the system status.

Condition

Procedure

Test mode (signal check mode) DTCs are output

Repair the faulty part and re-enter the "Signal Check" mode

Test mode (signal check mode) DTCs are cleared

No symptoms

(i) End of Test Mode (Signal Check Mode)

(1) After the test mode (signal check mode) is completed, turn the ignition switch to the OFF position and disconnect the Techstream.

(j) Test Mode (Signal Check Mode) DTCs

(1) If a malfunction code is displayed during the test mode (signal check mode) DTC check, refer to the diagnostic procedure for that code. For details on each code, refer to the link below.

DTC No.

Detection Item

Suspected Area

Link

*: With conventional spare tire

C2181/81

Transmitter ID1 not received

  • Tire pressure valve and transmitter
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

C2182/82

Transmitter ID2 not received

  • Tire pressure valve and transmitter
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

C2183/83

Transmitter ID3 not received

  • Tire pressure valve and transmitter
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

C2184/84

Transmitter ID4 not received

  • Tire pressure valve and transmitter
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

C2185/85*

Transmitter ID5 not received

  • Tire pressure valve and transmitter
  • Wire harness or connector
  • Tire pressure warning ECU and receiver

C2198/98

Initialization switch error

  • Steering pad switch assembly
  • Spiral Cable Sub-assembly
  • Wire harness or connector
  • Tire pressure warning ECU and receiver